NOTE: Please read all instructions carefully before using this product Table of Contents Safety Notice BODYFLEX GYM Hardware Identifier Assembly Instruction WM 1407 Parts List Resistance Chart Warranty Ordering Parts Model WM 1407 Retain This Manual for Reference 06-04-02 IMPEX FITNESS PRODUCTS OWNER'S MANUAL 14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746 Tel: (800) 999-8899 Fax: (626) 961-9966 www.impex-fitness.com info@impex-fitness.
TABLE OF CONTENTS BEFORE YOU BEGIN....................................................................................……….. 1 IMPORTANT SAFETY NOTICE....................................................................……….. 2 HARDWARE IDENTIFIER.....….....................................................................……….. 3 ASSEMBLY INSTRUCTIONS.........................................................................……….. 4 PARTS LIST…………………………………………………………………………………..
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one person at a time should use the machine. 3.
3
ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended two or more people assemble this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Attach the Base Frame (#5) to the Rear Base Frame (#6). Align the holes then secure them with one 4 3/8” x 1 ¾” Bracket (#19), two M10 x 2 ½” Carriage Bolts (#38), two ∅ ¾” Washers (#53), and two M10 Aircraft Nuts (#50). B.
STEP 2 (See Diagram 2) A.) Attach the Rear Support Frame (#4) onto the Base Frame (#5). Secure them with four M10 x 5/8” Allen Bolts (#40) and ∅ ¾” Washers (#53). B.) Attach the lower end of Diagonal Support Frame (#11) and the Vertical Lock Bracket (#14) to the Rear Support Frame (#4). Align the holes then secure them together with two M10 x 2 3/8” Carriage Bolts (#39), ∅ ¾” Washers (#53), and M10 Aircraft Nuts (#50). Do not tighten the nuts and bolts yet. C.
STEP 3 (See Diagram 3) A.) Attach the Upper Frame (#10) onto the Rear Vertical Frame (#9). Align the holes and secure it with five M10 x 5/8” Allen Bolts (#40) and ∅ ¾” Washers (#53). B.) Attach the two Bow Frames (#7) to each side of Rear Vertical Frame. Align the holes and secure them together with two M10 x 5 ¾” Allen Bolts (#47), four ∅ ¾” Washers (#53), and two M10 Aircraft Nuts (#50). C.) Attach one Swivel Pulley Bracket (#8) to each Bow Frame.
STEP 4 (See Diagram 4) A.) Attach two Bushings (#60) to the last hole on the Main Seat Support (#3). Attach the Main Seat Support (#3) to the Vertical Lock Bracket (#14). Secure the back hole with one M10 x 2 ½” Allen Bolt (#44), two ∅3/4” Washers (#53), and one M10 Aircraft Nut (#50). Note: Do not over tighten the nut and bolt. The Support needs to be able to swivel on the bolt. Secure the front hole with a Lock Pin (#57). Remove the Pin when folding up the machine. B.
STEP 5 (See Diagram 5) A.) Place the Backrest Board (#24) onto the Main Seat Support (#3). Secure it with four M8 x 5/8” Allen Bolts (#49) and ∅ ½” Washers (#54). B.) Place the Seat (#23) on the Main Seat Support. Secure it with four M8 x 5/8” Allen Bolts (#49) and ∅ ½” Washers (#54). C.) Insert one Foam Roll Tube (#12) halfway through the hole on the Front Stabilizer. Insert one Foam Roll Tube halfway through the hole on the Leg Developer. Push four Foam Rolls (#37) onto the Tubes from both sides.
STEP 6 (See Diagram 6) A.) Attach the Black Cable (#27), Red Cable (#25), and Blue Cable (#26) to three Small Pulleys (#17). Attach the three Pulleys to the open bracket on top of the Bow Frame (#7). Align the holes and secure them together with one M10 x 3 ½” Allen Bolt (#46) and ∅ ¾” Washer (#53). Note: The plastic clips on the end of the Cables should be on the back of the bracket facing the back of the machine. B.) Pull the three Cables downward to the open bracket on the Rear Base Frame (#6).
STEP 7 (See Diagram 7) A.) Attach one 65 ¾” Upper Cable (#21) to a Large Pulley (#28). Attach the Large Pulley to an Upper Swivel Pulley Bracket (#13) on the Upper Frame. Secure the Large Pulley to the bracket with one M10 x 1 ¾” Allen Bolt (#42), two ∅3/4” Washers (#53), and one M10 Aircraft Nut (#50). B.) Draw the Upper Cable towards the back to the open bracket on the Upper Frame. Repeat Procedure B to install another Large Pulley. C.
DIAGRAM 7 11
STEP 8 (See Diagram 8) A.) Attach one end of the Leg Developer Cable (#22) to the bottom of Leg Developer (#1). Secure it with one M10 x 1” Allen Bolt (#41), two ∅ ¾” Washers (#53), and one M10 Aircraft Nut (#50). Do not over tighten the bolt. The cable ring needs to be able to swivel on the bolt. B.) Draw the Cable through the open slot to an open bracket on the Front Stabilizer (#2). Attach a Large Pulley (#28) to the bracket.
PARTS LIST KEY NO.
14
IMPEX INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX.
