NOTE: Please read all instructions carefully before using this product Table of Contents Safety Notice Hardware Identifier COMPETITOR HOME GYM WM-1508 Assembly Instruction Parts List Resistance Chart Warranty Ordering Parts Model WM-1508 Retain This Manual for Reference 08-8-06 OWNER'S MANUAL IMPEX® INC. 14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746 Tel: (800) 999-8899 Fax: (626) 961-9966 www.impex-fitness.com info@impex-fitness.
TABLE OF CONTENTS BEFORE YOU BEGIN....................................................................................……….. 1 IMPORTANT SAFETY NOTICES...................................................................……….. 2 HARDWARE PACK……….....….....................................................................……….. 4 ASSEMBLY INSTRUCTIONS.........................................................................……….. 7 PARTS LIST………………………………………………………………………………….. 19 RESISTANCE CHART…………...................
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one person at a time should use the machine. 3.
WARNING LABEL REPLACEMENT The warning labels shown here have been placed on the Rear Base Frame and Upper Frame. If the labels are missing or illegible, please call customer service at 1-800-888-8899 for replacements. Apply the labels in the location shown.
HARDWARE PACK 4
HARDWARE PACK 5
HARDWARE PACK 6
ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches, two Allen Wrenches, and one Philips Screwdriver. NOTE: It is strongly recommended this machine to be assembled by two or more people to avoid possible injury. STEP 1 (See Diagram 1) A.) Connect the two Lower Guide Rods (8) and two Upper Guide Rods (#9) with two Stud Bolts (#73). Firmly thread the Rods together. B.) Insert the Lower Guide Rods (#8) into the holes on the Rear Base Frame (#2).
DIAGRAM 1 8
STEP 2 (See Diagram 2) A.) Slide nine Weight Plates (#42) onto the Guide Rods. Make sure the groove on the Weight Plates all facing the back of the machine and downward. Insert the Selector Rod (#23) through the center hole on the Weight Plates. B.) Slide the Selector Stem (#41) onto the Guide Rods. Make sure the center groove faces downward. C.) Slide the Ring on the String of the Selector Pin (#34) onto the Selector Rod. D.) Attach the Upper Frame (#10) onto the two Guide Rods.
DIAGRAM 2 10
STEP 3 (See Diagram 3) A.) Attach the Front Press Base (#11) to the Upper Frame (#10). Secure it with one Axle (#29), two Ø ¾” Washers (#95), and two M10 Aircraft Nuts (#92). B.) Attach the Left Butterfly (#16) to the Front Press Base. Secure it with one M6 x 1 ¼” Allen Bolt (#74), Lock Ring (#72), and M6 Aircraft Nut (#91). Repeat the same step to install the Right Butterfly (#17). C.) Attach the Backrest Board (#38) to the Lower and Upper Vertical Frames (#6 & #7).
DIAGRAM 3 12
CABLE LOOP DIAGRAM 13
STEP 4 (See Diagram 4 & Cable Loop Diagram) A.) Attach the 124” Upper Cable (#50) to the opening at the front of the Upper Frame (#10). Note: The Ball Stopper on the cable should be underneath the Frame. B.) Attach a Pulley (#47) to the opening. Secure it with one M10 x 1 ¾” Allen Bolt (#86), two Ø ¾” Washers (#95), and one M10 Aircraft Nut (#92). C.) Draw the Cable towards the back of the machine to the open bracket on the Upper Vertical Frame (#7).
DIAGRAM 4 15
STEP 5 (See Diagram 5 & Cable Loop Diagram) A.) Attach one end of the 105” Butterfly Cable (#51) to the hook on the Right Butterfly (#17). B.) Draw the Cable to the right Swivel Pulley Bracket (#14). C.) Attach a Pulley to the bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#86), two Ø ¾” Washers (#95), and one M10 Aircraft Nut (#92). D.) Draw the Cable around the Pulley then downward. Attach the Cable to a Crossed Double Floating Pulley Bracket (#15). E.
STEP 6 (See Diagram 6 & Cable Loop Diagram) A.) Attach the 173” Lower Cable (#52) to the opening on the bottom of the Leg Developer (#4). B.) Attach a Pulley to the opening. Secure it with one M10 x 2 ½” Allen Bolt (#84), two Pulley Bushings (#37), and one M10 Aircraft Nut (#92). C.) Draw the Cable underneath the Pulley to the opening on the Front Base Fame (#3). Repeat Procedure B above to install a Pulley. D.
DIAGRAM 6 18
PARTS LIST KEY NO.
20
® IMPEX INC. LIMITED WARRANTY ® IMPEX Inc. ("IMPEX ") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX.
