NOTE: Please read all instructions carefully before using this product Table of Contents Safety Notice Hardware Identifier Assembly Instruction Parts List COMPETITOR WEIGHT BENCH WM-357 Warranty Ordering Parts Model WM-357 Retain This Manual for Reference 06-26-06 OWNER'S MANUAL IMPEX® INC. 14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746 Tel: (800) 999-8899 Fax: (626) 961-9966 www.impex-fitness.com info@impex-fitness.
TABLE OF CONTENTS BEFORE YOU BEGIN...................................................................................…. IMPORTANT SAFETY NOTICES..................................................................…. HARDWARE IDENTIFIER.....…....................................................................…. ASSEMBLY INSTRUCTIONS........................................................................…. EXPLODED DIAGRAM………………………………………………………………. PARTS LIST.......................................................
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one person at a time should use the machine. 3.
WARNING LABEL REPLACEMENT The Warning Label shown here has been placed on the Cross Brace. If the label is missing or illegible, please call customer service at 1-800-999-8899 for replacement. Apply the label in location shown.
HARDWARE IDENTIFIER 4
ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches NOTE: It is strongly recommended two or more people assembling this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Plug the two Upright End Caps (#24) onto the bottom of the Right & Left Upright Beams (#1 & #2). Secure each Cap with a ST5 Screw (#47). B.) Connect the two Upright Beams by a Cross Brace (#4) in the Mid-span.
STEP 2 (See Diagram 2) A.) Plug a Front Leg End Cap (#27) onto the bottom of Front Leg (#5). Attach the Front Leg to the Main Seat Support (#3). Secure it with three M8 x 5/8” Allen Bolts (#38) and Ø 5/8” Washers (#44). DO NOT tighten the Bolts yet. B.) Attach the Main Seat Support to the Cross Brace (#4). Attach the Main Seat Stabilizer (#10) to the Main Seat Support. Align the holes.
STEP 3 (See Diagram 3) A.) Attach the Leg Developer (#7) to the Front Leg (#5). Secure it with one M8 x 3 1/8” Allen Bolt (#39), two Ø 5/8” Washers (#44), and one M8 Aircraft Nut (#49). B.) Insert two Foam Tubes (#13) halfway through the holes on the Leg Developer. Push four Foam Rolls (#30) onto the Tubes from both sides. C.) Place a Spring Clip (#26) onto the weight post on the Leg Developer. The maximum weight capacity for Leg Developer is 100 lbs. D.
STEP 4 (See Diagram 4) A.) Attach the Backrest Supports (#12) onto both ends of the pivot on the Main Seat Support (#3). Place the other end rest against the Backrest Adjustment Bar (#35). B.) Place the Backrest Board (#34) onto the Backrest Supports. Secure it with four M6 x 1 ½” Hex Bolts (#41) and Ø ½” Washers (#45). C.) Place the Seat Pad (#33) onto the Main Seat Support. Secure it with four M6 x 1 ½” Hex Bolts (#41) and Ø ½” Washers (#45).
STEP 5 (See Diagram 5) A.) Attach the Arm Curl Pad (#32) to the Arm Curl Stand (#6). Secure it with two M8 x 5/8” Allen Bolts (#38) and Ø 5/8” Washers (#44). B.) Insert the Arm Curl Stand into the top opening on the Front Leg. Secure it with a Lock Knob (#16). C.) When using Leg Developer, remove the Arm Curl Stand from the Front Leg and Arm Curl Handle from the Leg Developer.
10
PARTS LIST KEY NO.
® IMPEX INC. LIMITED WARRANTY ® IMPEX Inc. ("IMPEX ") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX.
