NOTE: Please read all instructions carefully before using this product Table of Contents Safety Notice WM-MXS OLYMPIC BENCH Hardware Identifier Assembly Instruction Exploded Diagram Parts List Warranty Ordering Parts Model WM-MXS Retain This Manual for Reference May 31, 2001 OWNER'S MANUAL IMPEX INC. 14777 Don Julian Rd., City of Industry, CA 91746 Tel: (800) 999-8899 Fax (626) 961-9966 www.impex-fitness.com info@impex-fitness.
TABLE OF CONTENTS BEFORE YOU BEGIN....................................................................................................... IMPORTANT SAFETY NOTICE........................................................................................ HARDWARE IDENTIFIER................................................................................................ ASSEMBLY INSTRUCTIONS........................................................................................... EXPLODED DIAGRAM.................
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one person at a time should use the machine. 3.
3
ASSEMBLY INSTRUCTION Tools required to assembly the machine: Two Adjustable Wrenches and Two Allen Wrenches STEP 1 (SEE Diagram 1) A.) Connect the Right Upright Beam (#3) to the Rear Stabilizer (#14). Secure them with one Bracket (#17), two M10x 3 ¾” Carriage Bolts (#47), two M10 Aircraft Nuts (#50) and two ∅7/8” Washers (#48). Repeat the same procedure to assemble the Left Upright Beam (#2). B.) Connect these two Upright Beams by a Cross Brace (#13) in the mid span.
STEP 2 (SEE DIAGRAM 2) A.) Connect the Main Seat Support (#1) to the Rear Stabilizer (#14). Secure them with one Bracket (#17), two M10 x 3 ¾” Carriage Bolts (#47), ∅ 7/8” Washers (#48) and M10 Aircraft Nuts (#50). B.) Connect the Main Seat Support (#1) to the Front Stabilizer (#56). Secure them with one Bracket (#17), two M10 x 3 ¾” Carriage Bolts (#47), ∅ 7/8” Washers (#48) and M10 Aircraft Nuts (#50). C.) Slide the Sliding Block (#10) onto the Chromed Incline Adjustment Bar (#11).
STEP 3 (SEE DIAGRAM 3) A.) Attach two Bushings (#54) to the pivot on the Main Seat Support (#1). Attach the Seat Incline Support Bracket (#8) to the Bushings and align the holes. Secure it with a M10 x 4 ½” Allen Bolt (#40), two ∅7/8” Washers (#48), and a M10 Aircraft Nut (#50). Do Not over tighten this nut and bolt. The Bracket needs to be able to swing. B.) Attach two Bushings (#54) to the Seat Incline Support Bracket (#8). Attach two Seat Support Frames (#6) to the Bracket and align the holes.
STEP 4 (SEE DIAGRAM 4) A.) Attach four Bushings (#54) to the Seat Support Frame (#6). B.) Attach four Bushings (#54) to the Backrest Supports (#7). Attach one Backrest Support (#7) to the Seat Support Frame (#6). Align the holes. Please note the Backrest Support (#7) should be on the inside of the Seat Support Frame (#6). Secure them with one M10 x 2 3/8” Allen Bolt (#42) and M10 Aircraft Nut (#50). Repeat the same procedure to install the other side.
STEP 5 (SEE DIAGRAM 5) A.) Attach two Bushings (#54) to the pivot on the Main Seat Support (#1). B.) Attach the two Backrest Supports (#7) to the Pivot and align the holes. Secure them with one M10 x 6 ¼” Allen Bolts (#39), two ∅7/8” Washers (#48), and one M10 Aircraft Nut (#50). C.) Attach two Bushings (#54) to the pivot on the Sliding Block (#10). D.) Align the holes on the two Backrest Supports (#7) to the Pivot.
STEP 6 (SEE DIAGRAM 6) A.) Attach the Seat (#22) to the Seat Support Frame (#6). Secure it with four ∅3/4” Washers (#49) and M8 x 2” Allen Bolts (#44). B.) Attach the Backrest Board (#23) to the Backrest Support (#7). Secure it with four ∅3/4” Washers (#49) and M8 x 2” Allen Bolts (#44).
STEP 7 (SEE DIAGRAM 7) A.) Insert Leg Developer Holder (#9) into the top opening on the Main Seat Support (#1). Insert a Lock Knob (#36) into selected hole to obtain desired height. B.) Insert an Axle (#16) into the pivot on the Leg Developer (#4). Attach Leg Developer (#4) onto the bracket on the Leg Developer Holder (#9). Secure it with two M10 x ¾” Allen Bolts (#43) and ∅ 7/8” Washers (#48). C.) Slide one Foam Roll Tube (#15) halfway through the top hole on the Leg Developer Holder (#9).
11
PARTS LIST KEY NO.
IMPEX INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX.
