BPBIO750 User’s Manual BPBIO750_manual_ENG_A_190522.
Please note the important information below before reading this manual. Warning Failure to observe these precautions can result in personal injury or equipment damage. Caution Failure to comply with safety precautions can damage the equipment. Note Referring to notes can help improve equipment use. For any problems with BPBIO750 or any clinical questions, please contact us at the following: InBody Co., Ltd. [HEAD OFFICE] InBody Bldg.
Basic points A. Product Components The blood pressure monitor is a medical device for measuring blood pressure. B. User This blood pressure monitor must be used with medical professionals. C. Measuring person Adult / Children (more than 7 years old) with arm circumference 17cm ~42cm Caution Check that the patient has the following symptoms before using the blood pressure monitor.
BPBIO750_manual_ENG_A_190522.
BPBIO750 User’s Manual Contents I. Installing BPBIO750 A. Product Components 4 B. Operating Environment 5 C. Installation 5 D. Loading and Reloading Printer Paper 8 E. Replacing Cuff Cloth 9 F. Setup 11 G. Precautions for Maintenance 14 II. Blood Pressure Test A. Precautions for Measurement 15 B. Test Instructions 15 C. Test Posture 18 III. Transportation and Storage A. Cautions during Transportation 19 B. Repacking Instructions 20 C. Transportation and Storage Environment 20 IV.
I. Installing BPBIO750 A. Product Components BPBIO750 consists of the following components. Make sure all of the following components are present. check each component of the system for damage prior to installation. Basic Components BPBIO750 Power cable (AC 250V 10A 1.8m) 1 EA Two rolls of printing paper User’s Manual Two pieces of cuff cloth (One fitted) Optional Components Desk for BPBIO750, fixing screw 2 EA Chair for BPBIO750 Print Start Stop nes (Age 18 and Over ) urate diagnosis.
B. Installation Environment Please make sure of the proper environment before BPBIO750 installation. This equipment is suitable for indoor use. If installing the equipment outdoors, the following requirements must be fulfilled. Temperatures range 10 to 40ºC (50 to 104ºF) Relative humidity 30 to 75% RH Atmospheric pressure range 70 to 106 kPa C. Installation 1. Unpack the BPBIO750 package and remove the packing pads.
2. Place the equipment on a solid table that can withstand the weight of BPBIO750 (approx. 7.1kg). If dedicated desk for BPBIO750 is available, align the desk-fixing grooves on the bottom of BPBIO750 and the grooves on the desk and secure them with two fixing screws. * Dedicated desk for BPBIO750 is sold separately. Desk fixing grooves Desk grooves Fixing screws Caution • Install BPBIO750 on the floor where is flat and vibration free.
4. Use the anti-theft groove to prevent theft. * Theft protection cable is sold separately. * Use the anti-theft cable whick is used for laptop etc. 5. Turn the BPBIO750 on by pressing the power switch located on the back of the device. Power switch 6. When BPBIO750 is turned on, the following screen is displayed and a self-test is automatically performed. Caution • Do not operate or touch the device while it is self-testing(about 10 seconds). It may cause errors or the inaccurate test results. 7.
D. Loading and Reloading Printer Paper 1. Press the button below the Print button to open printer cover. PUSH 2. Check the orientation of the paper as shown below before inserting the paper inside the printer cover. After inserting the printer paper, let a certain amount of paper come out of the cover, and close the cover. Caution • The printer will not work if the paper is inserted incorrectly. • Remove all trash from previous printer paper rolls.
E. Replacing Cuff Cover The cuff cover of the BPBIO750 should be replaced periodically for sanitary purposes. Follow the guide below to replace the cuff cover 1. Turn BPBIO750 off before replacing cuff cover. Remove the front cover of the BPBIO750 by pushing downward. Loosen the screw with a screwdriver. Screw Front Cover Front ring 2. Separate the cuff cover attached to the back of the arm insertion section by pulling it inward. 3. Pull the cuff cover on the front of the arm insert to remove it.
4. Place the seam of the new cuff cover down as shown, attach the new cuff to the back of the front ring and the rear arm insertion section by pushing the border of it. Caution • Blood pressure results may be inaccurate if the seam does not face down. 5. Attach the previously removed front ring on the BPBIO750, secure it with a screw and close the front cover. Screw Front ring Front Cover Note • Two pieces of cuff cover are provided with the BPBIO750. (One is already mounted in the equipment.
F. Setup Set up consists of time setting, sound setting, result sheet printing option, pressure unit setting, communications setting, result sheet printing items setting. 1. Setting Setup 1) If you press and hold the Start/Stop button and the Print button at the same time for more than 2 seconds in the Home screen, then ‘ ’(time setting), which is the first screen of the Setup, blinks and the currently set status are shown in the Diastolic ( ) column and Pulse (Hour) column.
2. Setup Example The following is an example of changing the output of the result sheet from automatic printing to manual printing. 1) At the Home screen, press and hold Start/Stop button and Print button at the same time for more than 2 seconds. The ‘ ’ screen, which is the first screen of the Setup, and the currently set status are shown below. 2) Press UP / DOWN button to go to ‘Automatic Printing Options (‘ In the Pulse column, the existing setting value is ‘ ’ displayed. ’).
3. Detailed description of Setup items When in the Setup menu, the following informatioin will be displayed in the Systolic, Diastolic, and Pulse screen.
Blood pressure information Blood pressure information on the Results sheet output Not used Results sheet item Pulse graph on the Results sheet output Pulse Graph Not used Customized logo on the Result sheets output Logo Not used G. Precautions for Maintenance Caution • • • • • Never move the equipment while the power is on. Do not let foreign objects, like dust and liquid to enter the device. Foreign objects can damage electric components.
II. Blood Pressure Test A. Precautions for Measurement Caution • User should rest at least 5 to 10 minutes before the test. • Do not roll up the user’s sleeve, but take off thick clothes. • User should sit up straight in the chair. • Insert the user’s arm until the elbow is caught in the elbow groove. • Adjust the height of the chair so that the inserted upper arm and the heart are horizontal. • Test in a relaxed state. • User should not talk or move during the test. B. Test Instructions 1.
3. Insert the arm into the arm insertion portion untill the elbow is caught in the groove part as shown. * When aligning the elbow to the groove, the blue LED lights up on the groove part of the display. Groove Blue LED lights. 4. Press the Start/Stop button to start the test. 5. The pressure is automatically applied to the cuff, and the blood pressure is measured. * Do not talk or move during the test. * Relax while sitting up straignt.
6. The cuff is automatically released after completing the test. Wait for the cuff to fully loosen and pull out your arm. 7. Check the results on the screen. * Voice message and Results sheet come out depending on Setup. Systolic blood pressure Diastolic blood pressure Pulse rate · If the test is not completed normally due to a motion etc.
C. Test Posture For a correct test result, take a proper posture during the test. * The measurment can be performed using either the right or left arm. Arm insertion portion Adjust the height of the chair so the upper part of the right arm and the heart are horizontal with each other. Sit as close as possible to the BPBIO750 * Be sure to place the elbow in the elbow groove before starting the test. * Take off thick clothes, and don’t roll up the sleeves. 18 BPBIO750_manual_ENG_A_190522.
III. Transportation and Storage A. Cautions during Transportation To transport BPBIO750 safely, two people should keep the equipment parallel to the ground. Caution • Keep the equipment horizontal while transporting. 19 BPBIO750_manual_ENG_A_190522.
B. Repacking Instructions 1. Turn off the BPBIO750. 2. Remove all connected cables and put the cuff fixing pad into BPBIO750, and wrap in package protective vinyl. After then, put the equipment in the package box, insert the packing pad and close the package box. Package Protection Vinyl Cuff Fixing Pad Packing pads C. Transportation and Storage Environment BPBIO750 should be transported or stored under the following conditions.
IV. FAQ Frequently asked questions and answers for BPBIO750 are as follows. If a problem persists even after checking below, please contact Customer Service Center of InBody. InBody Customer Service Center (+82-80-501-3939) A. Error Code The error messages can be displayed on the screen if the error occurrs during the test. Please inform the error code to the Customer Service Center for the correct and fast support. B.
Question Answer TYPE: Fast-Acting Rated current: 2.5AL Rated voltage: 250V Spare fuse · Voice guide does not work. · Turn on the volume knob on the rear of the BPBIO750. · It may be occurred when the Sound is set to Beep sound output. ‘ ’. When the Sound is set to ‘ ’, only the beep sound is outputted. If the user wants the Voice sound output, change the Sound to ‘ ’. * Refer to the ‘Setup’ on page 11. · Results sheet is not printing.
C. Regarding the Test If problems cannot be resolved with the information below, please contact InBody. Question · Test result are incorrect. Answer · The arm and heart are not aligned during the test. Adjust the height of the chair to align the arm and heart. Correct testing posture. Incorrect testing posture. The arm is higher than the heart. Blood pressure value will be measured lower. Incorrect testing posture. The arm is lower than the heart. Blood pressure value will be measured higher.
Question · When should blood pressure be measured? Answer · Blood pressure may vary throughout the day, as shown below. Blood pressure classification of World Health Organization Number of patients It is becoming increasingly clear that a series of symptoms are associated with the increased blood pressure in the morning.
V. Others * BPBIO750 was manufactured by the quality control procedure of InBody Co., Ltd. InBody Co., Ltd. complies with ISO9001 and ISO13485 which are international quality management systems. * This equipment satisfies the common standard for electrical and mechanical safety of medical devices and the common standard for the safety of medical devices. A.
• Do not touch signal input, signal output or other connectors, and the patient simultaneously. • External equipment intended for connection to signal input, signal output or other connectors, shall comply with relevant IEC Standard (e.g., IEC60950 for IT equipment and IEC60601-1 series for medical electrical equipment). In addition, all such combination • system-shall comply with the standard IEC60601-1 and/or IEC60601-1-1 harmonized national standard or the combination.
Other Symbols Complies with AAMIES 6060-1 CSA-C22. 2 No.60601-1 European conformity Manufacturer Serial number Authorized representative in the EUROPEAN COMMUNTY Alternating current Operating instructions Disposal of old Electrical & Electronic Equipment (Application in the European Union and other European countries with separate collection system.) This symbol indicates that this product shall not be treated as household waste.
D. Product Specifications Test Instructions Oscillometric Test range Pressure: 0 to 300 mmHg Pulse: 30 to 240 bpm Degree of precision Pressure: ± 2mmHg Pulse: Within ± 1.5% Test result Systolic blood pressure, diastolic blood pressure, pulse rate, pulse pressure, mean blood pressure, rate pressure product Test Time Approx. 30 seconds on average (20-50 seconds depending on the pulse and blood pressure value) Pressurization Time Approx.
29 BPBIO750_manual_ENG_A_190522.
www.inbody.com ©2019 InBody Co., Ltd. All rights reserved. BM-ENG-H2-A-190522 BPBIO750_manual_ENG_A_190522.
