Owner manual

ManualsBrandsINCRA ManualsToolsJig Fence System

• Before using the INCRA Fence System and Right

Angle Fixture, carefully read and follow all of the

instructions and safety information in this manual.

• Always turn off the power and make sure that the bit or

blade is fully stationary before moving any component

of the INCRA Fence System to any new setting.

• When using the INCRA Fence System and Right Angle

Fixture with any other tools, make sure that all safety

guards and other safety equipment supplied by the

manufacturer of that tool are securely in place and

functional

• Never let any part of the INCRA Fence System or Right

Angle Fixture interfere with another tool’s safety guards

or other safety equipment.

•

• Use appropriate safety devices. Keep hands clear of

the bit or blade. Always use a push stick, rubber soled

push block, or other safety devices to keep your hands

safely away from the cutting tool.

• Never let the bit or blade come in contact with the

aluminum body of the INCRA Right Angle Fixture.

• Never attempt to hold your work to the INCRA Right

Angle Fixture using your hands alone. Always use a

clamp or other suitable holding device to securely hold

your work to the front face of the fixture.

• Never let the bit or blade come in contact with the

wooden runners on your INCRA Right Angle Fixture.

Always clamp a wooden stop to the outfeed end of the

fence to stop the forward motion of the Right Angle

Fixture before the bit contacts the wooden runners.

SAFETY

Important safety instructions for using the INCRA Fence System

Owner’s Manual

Please read this Owner’s

Manual before use and keep it at

hand for reference.

From simple routing operations

such as edge forming, grooving,

dadoing, or rabbeting, to high

quality joinery, your new INCRA

Fence System and Right Angle

Fixture combined with the INCRA

Jig Positioner will provide an

unlimited source of precision and

satisfaction for all your router table

projects. The T-slot design of the

Fence and Right Angle Fixture

permit the easy addition of user

made sub fences and auxiliary

faceplates for specialty

applications. Durable aluminum

construction and double laminated

Fence and Stop ensure reliable

performance for years to come.

Made in America by:

Taylor Design Group, Inc.

PO Box 810262

Dallas, TX 75381

Phone: 972-242-9975

www.incra.com

2005 by Taylor Design Group, Inc. Printed in the U.S.A. INCRA is a registered trademark of Taylor Design Group, Inc.

INCRA Products are protected by the following US Patents: #4,793,604, #4,930,221, #5,195,730, #5,725,074, #5,423,360, #5,716,045, #6,237,457, #6,557,601, #6,672,190

Other patents granted or pending.

Summary of content (4 pages)

PAGE 1
Owner’s Manual Please read this Owner’s Manual before use and keep it at hand for reference. From simple routing operations such as edge forming, grooving, dadoing, or rabbeting, to high quality joinery, your new INCRA Fence System and Right Angle Fixture combined with the INCRA Jig Positioner will provide an unlimited source of precision and satisfaction for all your router table projects.
PAGE 2
INCRA Fence & Stop - Assembly and Use Step 1. Attach the INCRA Jig to your router table. The INCRA Fence System is designed to work as the “front end” to the INCRA Jig Positioner, so the first step is to attach your INCRA Jig to your router table. After following the instructions in the INCRA Jig owner’s manual for attaching your INCRA Jig to a wooden base panel, use C-clamps to attach the base panel to your router table as shown in Fig. 1.
PAGE 3
Step 4. Assemble and attach stop positioner. Fig. 4 To assemble the stop positioner, insert the (2) 1/4-20 x 1 3/4” hex bolts from hardware pack D-03 through the holes on the stop. Add the two washers and loosely attach the 1/4-20 thumb knobs. Now slide the hex bolt heads into the T-slot on the outfeed end of the INCRA Fence, Fig. 4. Position the stop as needed, and tighten the thumb knobs before use.
PAGE 4
INCRA Right Angle Fixture - Assembly and Use Step 1. Attach faceplate to base. Fig. 8 Assemble Right Angle Fixture Attach the INCRA Right Angle Fixture faceplate to the INCRA Right Angle Fixture base using the (4) supplied 10-32 x 5 1/2” hex bolts and rectangular nuts. Insert the bolts through the four Fig. 8A Faceplate alignment holes in the base and loosely attach the (4) rectangular nuts. Now slide the T-slots on the back of the faceplate over the rectangular nuts, Fig. 8.