Instruction Manual

ManualsBrandsINCRA ManualsHardwareMast-R-Lift II

Thank you for choosing this product from

JessEm Tool Company. We appreciate your

support and hope that our product serves you

well. This product is designed to provide

many years of reliable service provided it is

used as intended and taken care of.

This user manual will assist you in assembly

and general operation of this product. It is

not our intent to teach you about

woodworking. It is assumed that you are an

experienced woodworker with the basic skills

and experience necessary to use this product

safely. If after reading the following

instructions, if you are unsure or

uncomfortable about safely using this

product we urge you to seek additional

information through widely available

woodworking books or classes.

Suggested Router Bit Speeds

Bit Diameter Max. Speed

1” (25mm) 24,000 RPM

1-1/4” - 2” (30-50mm) 18,000 RPM

2-1/4” - 2-1/2” (55-65mm) 16,000 RPM

3” - 3-1/2” (75-90mm) 12,000 RPM

As part of our Continuous Product

Improvement Policy, JessEm products are

always advancing in design and function.

Therefore there may be differences between

what is shown in our catalogs, website or at

retail display and what is sold at time of

purchase. We reserve the right to make

positive changes to our products at our

discretion.

CONTENTS:

1 - Mast-R-Lift™ II

1 - Height Adjustment Handle

10 - 1/4-28 x 1/4” Leveling Set Screws

1 -Start Pin

1 - 3/16” hex key

Also includes:

5 - Magna Lock Insert Rings

1 - 3/32” Hex Key

1 - 1/8” Hex Key

1 - 5/32” Hex Key

1 - 1/4-20 x 1/4” Cam Screw

IMPORTANT!

Read and understand the contents of

this manual before assembly or

operation of this product.

User Manual

Model #02120, 02121

100 Caplan Ave., Units 14 & 15

Barrie, Ontario L4N 9J2

Canada

866-272-7492 Toll Free

705-726-8233 Local Phone

705-726-7519 Fax

Email: jessem@jessem.com

Website: www.jessem.com

Mast R Lift

™

INCRA

Summary of content (7 pages)

PAGE 1
INCRA Mast R Lift™ II User Manual Model #02120, 02121 100 Caplan Ave., Units 14 & 15 Barrie, Ontario L4N 9J2 Canada 866-272-7492 Toll Free 705-726-8233 Local Phone 705-726-7519 Fax Email: jessem@jessem.com Website: www.jessem.com Thank you for choosing this product from JessEm Tool Company. We appreciate your support and hope that our product serves you well. This product is designed to provide many years of reliable service provided it is used as intended and taken care of.
PAGE 2
IMPORTANT SAFETY PRECAUTIONS INSTALLING THE ROUTER  Before operating any router, read and understand all safety instructions in the owner’s manual that came with the router.  If you do not have a manual, contact the manufacturer and obtain one before using any power tool.  Always wear eye protection in compliance with ANSI safety standards when operating any power tool.  Always use proper guards and safety devices when operating power tools and machinery.  Carefully check router bits before each use.
PAGE 3
2. Locate your router on the chart below. 3. Align the letter and number associated with your router (Figures 3 and Figure 4) and reinsert and tighten the ¼- x 1-1/2” Shoulder Bolt you removed in step 2. 4.
PAGE 4
5. With the Mast-R-Lift II Crank Handle loosen the tensioning cap screw sufficiently to force the carriage to spread (Figure 5). This allows the router to be installed easily. 8. With the Mast-R-Lift™ II Crank handle, retighten the tensioning cap screw. (Figure 7) INSTALLING A JESSEM LIFT IN A CUSTOM ROUTER TABLE APPLICATION Figure 5 6.
PAGE 5
1. Place the insert ring into the center hole of the Lift’s top plate (Fig. 5). 2. With the insert wrench provided, insert the prongs of the wrench into the corresponding holes in the insert ring and turn the insert ring counter clockwise to tighten. Figure 9 Turn the insert wrench clockwise to loosen and remove the ring. If the insert ring becomes too tight to loosen with hand pressure, a tap clockwise on the insert wrench with a block of wood will loosen it.
PAGE 6
To lock your lift turn lift handle clockwise to the “LOCKED” position Figure 12 To unlock your lift turn lift handle counterclockwise to the “UNLOCKED” position 3. Slide the carriage all the way up towards the top plate of your Mast-RLift™ II RE-ADJUSTING THE THREAD TENSION All JessEm Lifts feature our patented thread tensioning design. Thread tension is set at the factory and depending on the amount of use you may have to reset this adjustment periodically, depending on the amount of tension you desire.
PAGE 7
2 A 1 4 Figure 15 6. B 3 Place back the o-ring and carriage nut cap and with the screws you removed in Step 2 (Figure 11) fasten the carriage nut cap securely JESSEM TOOL LIMITED WARRANTY All JessEm products are warranted to be free from defects in material and workmanship. JessEm will repair or replace any product which upon inspection proves to be defective for a period of (1) year from dated receipt and proof of purchase. All warranty claims should be made direct to JessEm Tool Company.