7HPCN 640T (OW) R/HA 7HPCN 640T (AN) R/HA English Operating Instructions HOB Operating Instructions,1 Warnings,2 Assistance,2 Description of the appliance,3 Installation,4 Start-up and use,8 Precautions and tips,8 Maintenance and care,9 Troubleshooting,9 Contents
Warnings WARNING: The appliance and its accessible parts become hot during use. Care should be taken to avoid touching heating elements. Children less than 8 years of age shall be kept away unless continuously supervised.
Description of the appliance Overall view 1. 2. 3. 4. 5. Support Grid for COOKWARE GAS BURNERS Control Knobs for GAS BURNERS Ignition for GAS BURNERS SAFETY DEVICES • GAS BURNERS differ in size and power. Use the diameter of the cookware to choose the most appropriate burner to cook with. • Control Knobs for GAS BURNERS adjust the size of the flame. • GAS BURNER IGNITION enables a specific burner to be lit automatically. • SAFETY DEVICE stops the gas flow if the flame is accidentally extinguished.
Positioning ! Keep packaging material out of the reach of children. It can become a choking or suffocation hazard (see Precautions and tips). ! The appliance must be installed by a qualified professional according to the instructions provided. Incorrect installation may cause harm to people and animals or may damage property. ! This unit may be installed and used only in permanently ventilated rooms in accordance with current national regulations.
• Where the hob is not installed over a built-in oven, a wooden panel must be installed as insulation. This must be placed at a minimum distance of 20 mm from the lower part of the hob. Ventilation To ensure adequate ventilation, the back panel of the cabinet must be removed. It is advisable to install the oven so that it rests on two strips of wood, or on a completely flat surface with an opening of at least 45 x 560 mm (see diagrams). 560 mm . 45 m m.
EN Replacing the Triple ring burner nozzles 1. Remove the pan supports and lift the burners out of their housing. The burner consists of two separate parts (see pictures). 2. Unscrew the nozzles using a 7 mm socket spanner. Replace the nozzles with models that are configured for use with the new type of gas (see Table 1). The two nozzles have the same hole diameter. 3. Replace all the components by completing the above operations in reverse order.
Burner and nozzle specifications EN Table 1 Liquid Gas Diameter (mm) Burner (mm) Nozzle 1/100 (mm) Thermal Thermal By-pass Power Power 1/100 kW (p.c.s.*) kW (p.c.s.*) Reduced Nominal Natural Gas Flow* g/h *** ** Thermal Power kW (p.c.s.*) Nominal Nozzle 1/100 (mm) Flow* l/h Reduced Rapid (RR) 100 0.70 2.60 39 80 189 186 2.60 122(H3) 248 Semi Rapid (S) 75 0.40 1.65 28 64 120 118 1.65 96(Z) 157 Auxiliary (A) 55 0.40 1.00 28 50 73 71 1.
EN Start-up and use Precautions and tips ! The position of the corresponding gas burner or electric hotplate* is shown on every knob. ! This appliance has been designed and manufactured in compliance with international safety standards. The following warnings are provided for safety reasons and must be read carefully.
400011210138 01/2018 - XEROX FABRIANO on the product reminds you of your obligation, that when you dispose of the appliance it must be separately collected. Consumers should contact their local authority or retailer for information concerning the correct disposal of their old appliance. Respecting and conserving the environment • Cook your food in closed pots or pans with well-fitting lids and use as little water as possible. Cooking with the lid off will greatly increase energy consumption.
