Instruction for Use
GB
19
NL2L1
400V 2N~
H05RR-F 4x4 CEI-UNEL 35363
H05VV-F 4x4 CEI-UNEL 35746
1
3
2
4
5
NL3L1L2
400V 3N~
H05RR-F 5x2.5 CEI-UNEL 35363
H05VV-F 5x2.5 CEI-UNEL 35746
1
3
2
4
5
• Secure the power supply cable by fastening the cable clamp
screw then put the cover back on.
Connecting the supply cable to the electricity mains
Install a standardised plug corresponding to the load indicated
on the appliance data plate (see Technical data table).
The appliance must be directly connected to the mains using
an omnipolar switch with a minimum contact opening of 3 mm
installed between the appliance and the mains. The switch
must be suitable for the charge indicated and must comply with
current electrical regulations (the earthing wire must not be
interrupted by the switch). The supply cable must be positioned
so that it does not come into contact with temperatures higher
than 50°C at any point.
Before connecting the appliance to the power supply, make sure
that:
• The appliance is earthed and the plug is compliant with the law.
• The socket can withstand the maximum power of the
appliance, which is indicated by the data plate.
• The voltage falls between the values indicated on the data
plate.
• The socket is compatible with the plug of the appliance. If
the socket is incompatible with the plug, ask an authorised
technician to replace it. Do not use extension cords or multiple
sockets.
! Once the appliance has been installed, the power supply cable
and the electrical socket must be easily accessible.
! The cable must not be bent or compressed.
! The cable must be checked regularly and replaced by authorised
technicians only.
! The manufacturer declines any liability should these safety
measures not be observed.
We recommend cleaning the oven before using it for the rst
time, following the instructions provided in the „Care and
maintenance” section.
Safety Chain
! In order to prevent accidental tipping of the appliance, for
example by a child climbing onto the oven door, the supplied
safety chain MUST be
installed!
The cooker is fi tted with a
safety chain to be fi xed by
means of a screw (not sup-
plied with the cooker) to the
wall behind the appliance, at
the same height as the chain
is attached to the appliance.
Choose the screw and the
screw anchor according to
the type of material of the
wall behind the appliance. If
the head of the screw has a diameter smaller than 9mm, a washer
should be used. Concrete wall requires the screw of at least 8mm of
diameter, and 60mm of length.
Ensure that the chain is fi xed to the rear wall of the cooker and
to the wall, as shown in fi gure, so that after installation it is
tensioned and parallel to the ground level.
TABLE OF CHARACTERISTICS
Oven dimensions
(HxWxD)
32x43.5x40 cm
Volume
56 l
Useful
measurements
relating to the oven
compartment
width 42 cm
depth 44 cm
height 8.5 cm
Burners
Voltage and
frequency
see data plate
Data plate, is located inside the
flap or, after the oven
compartment has been opened,
on the left-hand wall inside the
oven.
Glass Ceramic Hob
Front Left
Back Left
Back Right
Front Right
Max. Ceramic Hob
Consumption
1700W
1200W
2300W
1200W
6400W
ENERGY LABEL
Directive 2002/40/EC on the label of
electric ovens. Standard EN 50304
Energy consumption for Natural
convection – heating mode:
Convection mode
Declared energy consumption for
Forced convection Class
– heating mode: Roasting
EC Directives: 2006/95/EC dated
12.12.06 (Low Voltage) and
subsequent amendments - 04/108/EC
dated 15/12/04 (Electromagnetic
Compatibility) and subsequent
amendments - 93/68/EEC dated
22/07/93 and subsequent
amendments - 2002/96/EC.
1275/2008 (Stand-by/Off mode)