HHC6.7AB HHC9.7AB HHC7.
6x Ø 8 x 40 6x Ø 5 x 45 4x Ø 3,5 x 9,5 1x 2 3 4 5 2x ø 150-125mm ø 150mm 1x 1x 1x 2
min.
2 3 = = = x6 = 55 0m 65 m 0 m m 4 5 Ø 8 mm x6 7 5 m m 6 4 x6 x2
8 9 1 2 x2 3 10 11 ø 150 ø 120 x2 12 13 5
14 x2 ø 150 ø 3,5 x 9,5 15 16 17 18 B A 6
Warnings ! Keep this manual for reference. If you sell, transfer or move the unit to another location, make sure to keep the manual with the product. ! Read the instructions carefully - they contain important installation, user and safety information. ! Do not tamper with the electrical or mechanical equipment of the product or its exhaust ducts.
• Strictly observe all local regulations in relation to the technical and safety measures to be employed in fumes extraction. • Clean the product frequently, inside and out (AT LEAST ONCE A MONTH, and in observance of the maintenance instruction given in this manual). • Failure to observe the hood cleaning and filter cleaning/replacement instructions can result in fires. • Never use the hood without its bulbs properly installed - electrocution hazard.
Installation The installation procedure is illustrated in the first pages of this manual. The installation must be done by a qualified technician. Electrical hook up The mains voltage must match that given on the ratings label inside the hood itself. If the hood has a power plug, connect the hood to an easily accessible regulatory power socket.
GB Grease/odour filter warnings The T2 icon flashes to indicate that the grease filter is saturated, while T3 flashes to indicate that the odour filter is saturated, and if both are flashing then both filters are saturated. You must then clean/replace the grease filter (A) or odour filter (B) or both, accordingly (see “Maintenance and care”).
Grease/odour filter warnings The bar at the top left flashes to indicate that the grease filter is saturated. The bar at the top right flashes to indicate that the odour filter is saturated. If both bars are flashing, then both filters are saturated. You must then clean/replace the grease filter (A) or odour filter (B) or both, accordingly (see “Maintenance and care”). The latter only applies to the filter version. To reset the filter counter: Hold down T4 for three seconds while the hood is on.
GB Replacing the bulbs Disconnect the unit from the mains and remove the grease filter. Caution! Make sure the bulbs are cool before touching them. 1. Extract the guard by prising it out with a small flat head screwdriver or something similar. 2. Replace the faulty bulb. Use only bulbs of the same type (for details, see the technical data in the following manual). 3. Refit the guard (push it in). Replacing the lights LED * The hood is fitted with a lighting system based on LED technology.
GB PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24 13
GB After Sales Service No one is better placed to care for your Hotpoint appliance during the course of its working life than us – the manufacturer. Essential Contact Information Hotpoint Service We are the largest service team in the country offering you access to 400 skilled telephone advisors and 1000 fully qualified engineers on call to ensure you receive fast, reliable, local service. UK: 08448 224 224 Republic of Ireland: 0818 313 413 www.hotpointservice.co.
Guarantee GB 12 months Parts and Labour Guarantee Your appliance has the benefit of our manufacturer’s guarantee, which covers the cost of breakdown repairs for twelve months from the date of purchase. This gives you the reassurance that if, within that time, your appliance is proven to be defective because of either workmanship or materials, we will, at our discretion, either repair or replace the appliance at no cost to you.
195107498.
