Instructions for use WASHING MACHINE Contents GB English,1 GB Installation, 2-3-4-5-6-7 Unpacking and levelling Electric and water connections The first wash cycle Technical details Instructions for the fitter Washing machine description, 8-9 Control panel Leds Starting and Programmes, 10 Briefly: how to start a programme Programme table Personalisations, 11 IWME 126 Setting the temperature Setting the spin speed Functions Detergents and laundry, 12 Detergent dispenser Bleach cycle Preparing your la
Installation ! Keep this instruction manual in a safe place for future reference. Should the appliance be sold, transferred or moved, make sure the instruction manual accompanies the washing machine to inform the new owner as to its operation and features. GB ! Read these instructions carefully: they contain vital information on installation, use and safety. Unpacking and levelling Unpacking 1. Unpack the washing machine. 2. Check whether the washing machine has been damaged during transport.
Connecting the drain hose 65 - 100 cm Connect the drain hose, without bending it, to a draining duct or a wall drain situated between 65 and 100 cm from the floor; • the supply voltage is included within the values i ndicated on the Technical details table (see page 5); GB • the socket is compatible with the washing machine's plug. If this is not the case, replace the socket or the plug. Your appliance is now supplied with a 13 amp fused plug it can be plugged into a 13 amp socket for immediate use.
As the colours of the wires in the lead may not correspond with the coloured markings identifyng the terminals in your plug, proceed as follows: Connect Green & Yellow wire to terminal marked E or coloured Green or Green & Yellow. or Connect Brown wire to terminal marked L or coloured Red. Connect Blue wire to terminal marked N or coloured Black. If a 13 amp plug (BS 1363) is used it must be fitted with a 13 amp fuse, either in the plug or adaptor or at the distribution board.
Technical details Model IWME 126 Dimensions 59.5 cm wide 81,5 cm high 54,5 cm deep Capacity from 1 to 6 kg Electric connections please refer to the technical data plate fixed to the machine Water connections maximum pressure 1 MPa (10 bar) minimum pressure 0.05 MPa (0.5 bar) drum capacity 52 litres Spin speed up to 1200 rpm Control programmes according to EN 60456 directive programme 2; temperature 60°C; run with a load of 6 kg.
Instructions for the fitter GB Door Mounting Accessories (Fig. 1-2-3-4-5). Mounting the wooden panel onto the door and inserting the machine into cabinets: In the case where the machine must be shipped for final installation after the wooden panel has been mounted, we suggest leaving it in its original packaging. The packaging was designed to make it possible to mount the wooden panel onto the machine without removing it completely (see figures below).
Using the Drilling Template. - To trace the positions of the holes on the left-hand side of the panel, align the drilling template to the top left side of the panel using the lines traced on the extremities as a reference. - To trace the positions of the holes on the right-hand side of the panel, align the drilling template to the top right side of the panel. - Use an appropriately sized router to mill the holes for the two hinges, the rubber plug and the magnet.
Washing machine description Control panel FUNCTION GB ON-OFF/DOOR LOCK Led Buttons Leds ON-OFF Button PROGRAMME Detergent dispenser Knob SPIN SPEED START/RESET Knob Button TEMPERATURE Knob Detergent dispenser: to add detergent and fabric softener (see page 12). TEMPERATURE knob: to set the temperature or the cold wash cycle (see page 11). LEDS: to find out which wash cycle phase is under way.
Leds The LEDS provide important information. This is what they can tell you: Cycle phase under way: During the wash cycle, the LEDs gradually illuminate on to indicate the cycle phase under way: GB Prewash Delay set: If the Delay Timer function has been enabled (see page. 11), once you have started the programme, the LED corresponding to the delay set will begin to flash: Wash Rinse Spin cycle Note: during draining, the LED corresponding to the Spin cycle phase will be turned on.
Starting and Programmes Briefly: starting a programme GB 6. Add the detergent and any fabric softener (see page 12). 7. Start he programme by pressing the START/RESET button. To cancel it, keep the START/RESET button pressed for at least 2 seconds. 8. When the programme is finished, the ON-OFF/ DOOR LOCK Led will flash to indicate that the appliance door can be opened. Take out your laundry and leave the appliance door ajar to allow the drum to dry thoroughly. Turn the washing .
Personalisations Setting the temperature Turn the TEMPERATURE knob to set the wash temperature (see Programme table on page 10). The temperature can be lowered, or even set to a cold wash ( ). GB Setting the spin speed Turn the SPIN SPEED knob to set the spin speed for the programme selected. The maximum spin speeds for each programme are as follows: Programmes Maximum spin speed Cottone 1200 rpm Synthetics 800 rpm Wool 600 rpm Silk no .
Detergents and laundry GB Detergent dispenser Preparing your laundry Good washing results also depend on the correct dose of detergent: adding too much detergent won't necessarily make for a more efficient wash, and may in fact cause build up on the interior of your appliance and even pollute the environment. • Divide your laundry according to: - the type of fabric/the symbol on the label. - the colours: separate coloured garments from whites. • Empty all pockets and check for loose buttons.
Precautions and advice ! The washing machine was designed and built in compliance with the applicable international safety regulations. The following information is provided for your safety and should consequently be read carefully. General safety • This appliance has been designed for nonprofessional, household use and its functions must not be changed. • This washing machine should only be used by adults and in accordance with the instructions provided in this manual.
Care and maintenance GB Cutting off the water or electricity supply 2. clean the interior thoroughly; 3. screw the lid back on. • Turn off the water tap after every wash. This will limit the wear of your appliance's water system and also prevent leaks. • Unplug your appliance when cleaning it and during all maintenance operations. Checking the water inlet hose Cleaning your appliance The exterior and rubber parts of your appliance can be cleaned with a soft cloth soaked in lukewarm soapy water.
Troubleshooting Your washing machine could fail to work. Before calling for Assistance (see page 16), make sure the problem can't easily be solved by consulting the following list. GB Problem Possible causes/Solution: The washing machine won't start. • The appliance is not plugged into the socket, or not enough to make contact. • There has been a power failure. The wash cycle won't start. • • • • • The appliance door is not shut properly. button has not been pressed.
Service Before calling for Assistance: • Check whether you can solve the problem on your own (see page 15); • Restart the programme to check whether the problem has been solved; • If this is not the case, contact an authorised Technical Service Centre on the telephone number provided on the guarantee certificate. GB ! Always request the assistance of authorised servicemen. Notify the operator of: • the type of problem; • the appliance model (Mod.); • the serial number (S/N).
Guarantee 12 Months Parts and Labour Guarantee Your appliance has the benefit of our manufacturer’s guarantee, which covers the cost of breakdown repairs for twelve months from the date of purchase. This gives you the reassurance that if, within that time, your appliance is proven to be defective because of either workmanship or materials, we will, at our discretion, either repair or replace the appliance at no cost to you.
After Sales Service GB No one is better placed to care for your Indesit appliance during the course of its working life than us - the manufacturer. Essential Contact Information Indesit Service We are the largest service team in Europe offering you access to 400 skilled telephone advisors and 1100 fully qualified engineers on call to ensure you receive fast, reliable, local service. UK: 08448 224 224 Republic of Ireland: 0818 313 413 www.indesitservice.co.
195076776.