Instruction for Use

ManualsBrandsIndesit ManualsDomestic AppliancesKBT 6424 DO IX/HA

Connecting the hob

 The electrical safety of this appliance can only be

guaranteed if the latter is correctly and efficiently earthed, in

compliance with regulations on electrical safety. Always

ensure that this vital safety measure has been taken. If you

have any doubts, call in a qualified technician to check the

electrical system thoroughly.

 The manufacturer denies all responsibility for damage

resulting from a system which has not been earthed

correctly.

 Before powering the appliance, check whether the

technical characteristics featured on the appliance data

plate correspond with those of the mains electrical system.

 Check that the current load of the mains supply and of the

power sockets is suitable for the maximum power of the

appliance, indicated on the appliance data plate. If in doubt,

contact a qualified professional.

Disconnect the appliance from the electricity supplyDisconnect the appliance from the electricity supply

Disconnect the appliance from the electricity supply

before all operations.before all operations.

before all operations. Connect your hob to the electrical

system by means of a

junction box:junction box:

junction box: if the appliance is

connected permanently to the mains, an

omnipolar circuitomnipolar circuit

omnipolar circuit

breakerbreaker

breaker, accessible if necessary, with a minimum contact

opening of 3 mm should be installed.

Single-phase connection

The hob is equipped with a preconnected electricity supply

cable, which is designed for single-phase connection.

Connect the wires according to the instructions given in

the following table and diagrams:

Voltage and

mains frequency

Electrical cable Wire connection

230V 1+N ~

50 Hz

: yellow/green;

N: the two blue wires

together

L: brown and black

together

Other types of connection

If the mains supply corresponds with one of the following:

Voltage and mains frequency

 400V - 2+N ~ 50 Hz

 230V 3 ~ 50 Hz

 400V - 2+2N ~ 50 Hz

Separate the wires and connect them according to the

instructions given in the following table and diagrams:

Voltage and

mains frequency

Electrical cable Wire connection

400V - 2+N ~

50 Hz

230V 3 ~

50Hz

: yellow/green;

N: the two blue wires together

L1: black

L2: brown

400V - 2+2N ~

50 Hz

: yellow/green;

N1: blue

N2: blue

L1: black

L2: brown

If the mains supply corresponds with one of the following:

Voltage and mains frequency

 400V 3 - N ~ 50 Hz

proceed as follows:

! The cable provided is not suitable for the following types

of installation.

1. Use a suitable supply cable, H05RR-F or higher, with the

right dimensions (cable section: 2.5 mm).

2. To open the terminal board, insert a screwdriver into the

side tabs of the cover and open it (see Terminal board

picture).

3. Loosen the cable clamp screw and the terminal board

screws according to the type of connection required and

position the connection supports as shown in the following

table and diagrams.

4. Position the wires according to the following table and

diagrams and connect the appliance by tightening all the

screws for the springs as much as possible.

Voltage and

mains frequency

Electrical connections Terminal board

400V 3-N ~ ı 50

Three-phase 400

5. Secure the power supply cable by fastening the cable

clamp screw, then put the cover back on.

U-bolt

connection support

Phase PhasePhase Neutral Earth

Three-phase 400

This appliance conforms to the following

European Economic Community directives:

- 73/23/EEC dated 19/02/73 (Low Voltage) and subsequent

amendments;

- 89/336/EEC dated 03/05/89 (Electromagnetic

Compatibility) and subsequent amendments;

- 93/68/EEC dated 22/07/93 and subsequent amendments.

Disposal

 When disposing of packaging material: observe local

legislation so that the packaging may be reused.

 The European Directive 2002/96/EC relating to Waste

Electrical and Electronic Equipment (WEEE) states that

household appliances should not be disposed of using

the normal solid urban waste cycle. Exhausted

appliances should be collected separately in order to

optimise the cost of re-using and recycling the materials

inside the machine, while preventing potential damage to

the atmosphere and to public health. The crossed-out

dustbin is marked on all products to remind the owner of

their obligations regarding separated waste collection.

For further information relating to the correct disposal of

exhausted household appliances, owners may contact

the public service provided or their local dealer.