Instruction for Use

EN
26
Refined Salt and Rinse Aid
(°dH=hardnessmeasuredinGermandegrees-°f=hardness
measuredinFrenchdegrees–mmol/l=millimolesperlitre)
Measuring out the rinse aid
RinseaidmakesdishDRYINGeasier.Therinseaiddispenser
should be filled:
• WhentheLOWRINSEAIDindicatorlightonthepanel/display
is lit *;
• Whenthedarkopticalindicator* on the dispenser door “D”
becomes transparent.
1. Open the dispenser “D” by pressing and pulling up the tab
on the lid;
2.Carefully introducethe rinseaid as faras themaximum
reference notch in the filling space - avoid spilling it. If this
happens, clean the spill immediately with a dry cloth.
3.Presstheliddownuntilyouhearaclicktocloseit.
NEVER pour the rinse aid directly into the tub.
Adjusting the amount of rinse aid
If you are not completely satisfied with the drying results, you
may want to adjust the quantity of rinse aid used.
•SwitchthedishwasheronusingtheOn/Offbutton.
•SwitchitoffusingtheOn/Offbutton
•PresstheSTART/PAUSEbutton three times
•SwitchitonusingtheOn/Offbutton
•Everythingisoff
•Settheknobtothelevelnumberofrinseaidquantitytobe
supplied.
•SwitchitoffusingtheOn/Offbutton
•Settingiscomplete!
IftherinseaidlevelissettoZERO(ECO),norinseaidwillbe
supplied.TheLOWRINSEAIDindicatorlightwillnotbelitifyou
run out of rinse aid.
Amaximumof4levelscanbesetaccordingtothedishwasher
model. The factory setting is for a medium level.
• Ifyouseebluishstreaksonthedishes,setalownumber(1-2).
• Iftherearedropsofwaterorlimescalemarksonthedishes,
setahighnumber(3-4).
Only use products which have been specifically designed
for dishwashers. Do not use table salt or industrial salt.
Follow the instructions given on the packaging.
If you are using a multi-function product, we recommend
that you add salt in any case, especially if the water is hard
or very hard.
(Followtheinstructionsgivenonthepackaging.)
If you do not add salt or rinse aid, the LOW SALT* and
LOW RINSE AID
* indicator lights will remain lit.
Measuring out the refined salt
Theuse of saltprevents theformation ofLIMESCALE on the
dishes and on the machine’s functional components.
•Itisimportantthatthesaltdispenserbeneverempty.
•Itisimportanttosetthewaterhardness.
The salt dispenser is located in the lower part of the dishwasher
(seeDescription) and should be filled:
• WhentheLOWRINSEAIDindicatorlightinthecontrolpanel
is lit*;
• Whenthegreenfloat* on the cap of the salt dispenser is no
longer visible.
• Seeautonomyinthewaterhardnesstable.
1.Remove thelowerrack andunscrew the
containercap(anticlockwise).
2. Only the first time you do this: fill the water
dispenser up to the edge.
3.Positionthefunnel (seefigure) and fill the salt
containerrightuptoitsedge(approximately1
kg); it is not unusual for a little water to leak out.
4.Removethefunnelandwipeanysaltresidueawayfromthe
opening; rinse the cap under running water and then screw it on.
It is advisable to perform this procedure every time you add salt
to the container.
Make sure the cap is screwed on tightly, so that no detergent can
getintothecontainerduringthewashcycle(thiscoulddamage
the water softener beyond repair).
Whenever you need to add salt, we recommend carrying out
the procedure before the washing cycle is started.
Setting the water hardness
For perfect water softener operation, it is essential that the
adjustment be based on the water hardness in your house. Ask
your local water supplier for this information. The factory setting
is for medium water hardness.
•SwitchthedishwasheronusingtheOn/Offbutton.
•SwitchitoffusingtheOn/Offbutton
•HolddowntheSTART/PAUSEbutton for 5 seconds.
•SwitchitonusingtheOn/Offbutton
•Thesaltindicatorlightflashes(asmanytimesasthecurrent
selection.)
•Settheknob to the desired hardness level number (seeTable
on water hardness.)
•SwitchitoffusingtheOn/Offbutton
•Settingiscomplete!
Evenifusingmulti-functionaltablets,thesaltdispensershould
still be filled.
Water Hardness Table
Average autonomy
salt dispenser with 1
wash cycle per day
level °dH °fH mmol/l months
1 0 - 6 0 - 10 0 - 1 7 months
2 6 - 11 11 - 20 1.1 - 2 5 months
3 12 - 17 21 - 30 2.1 - 3 3 months
4 17 - 34 31 - 60 3.1 - 6 2 months
5
*
34 - 50 61 - 90 6.1 - 9 2/3 weeks
For values between 0°f and 10°f, we do not recommend the use
of salt. A setting of 5 may increase cycle duration.
M
A
X
* Only available in selected models.