Instructions for use WASHER-DRYER Contents GB English,1 NL DE Nederlands,13 Deutsch,25 GB Installation, 2-3 Unpacking and levelling, 2 Electric and water connections, 2-3 The first wash cycle, 3 Technical details, 3 Washer-dryer description, 4-5 Control panel, 4 Leds, 5 Starting and Programmes, 6 Briefly: how to start a programme, 6 Programme table, 6 Personalisations, 7 WIDL 146 Setting the temperature, 7 Setting the drying cycle, 7 Functions, 7 Detergents and laundry, 8 Detergent dispenser, 8
Installation Keep this instruction manual in a safe place for future reference. Should the appliance be sold, transferred or moved, make sure the instruction manual accompanies the Washer-dryer to inform the new owner as to its operation and features. GB Read these instructions carefully: they contain vital information on installation, use and safety.
Do not use extensions or multiple sockets. Connecting the drain hose The power supply cable must never be bent or dangerously compressed. The power supply cable must only be replaced by an authorised serviceman. GB Installation 65 - 100 cm Connect the drain hose, without bending it, to a draining duct or a wall drain situated between 65 and 100 cm from the floor; Warning! The company denies all liability if and when these norms are not respected.
Washer-dryer description Control panel GB FUNCTION Buttons Leds ON-OFF/ DOOR ON-OFF LOCK Button Led PROGRAMME Knob Detergent dispenser START/RESET Button DRYING Knob Knob Detergent dispenser: to add detergent and fabric softener (see page 8). TEMPERATURE knob: to set the temperature or the cold wash cycle (see page 7). LEDS: to find out which wash cycle phase is under way. If the Delay Timer function has been set, the time left until the programme starts will be indicated (see page 5).
Leds Delay set: If the Delay Timer function has been enabled (see page. 7), once you have started the programme, the LED corresponding to the delay set will begin to flash: Prewash / Wash Rinse Spin cycle Note: - during draining, the LED corresponding to the Spin cycle phase will be turned on. Detergents Once the set delay is complete, the flashing LED will turn off and the programme set will start. Function buttons The FUNCTION BUTTONS also act like LEDS.
Starting and Programmes Briefly: starting a programme GB 6. Add the detergent and any fabric softener (see page 8). 7. Start he programme by pressing the START/RESET button. To cancel it, keep the START/RESET button pressed for at least 2 seconds. 8. When the programme is finished, the ON-OFF/ DOOR LOCK Led will flash to indicate that the appliance door can be opened. Take out your laundry and leave the appliance door ajar to allow the drum to dry thoroughly. Turn the Washer-dryer .
Personalisations C Setting the temperature Turn the TEMPERATURE knob to set the wash temperature (see Programme table on page 6). The temperature can be lowered, or even set to a cold wash ( ). Turn the DRYING knob to set the desired drying type. Two options are available: A - Based on time: From 40 minutes to 150. A cooling stage is foreseen at the end of the drying cycle.
Detergents and laundry GB Detergent dispenser Special items Good washing results also depend on the correct dose of detergent: adding too much detergent won't necessarily make for a more efficient wash, and may in fact cause build up on the interior of your appliance and even pollute the environment. Curtains: fold curtains and place them in a pillow case or mesh bag. Wash them separately without exceeding half the appliance load. Use programme 6 which excludes the spin cycle automatically.
Precautions and advice General safety This appliance has been designed for nonprofessional, household use and its functions must not be changed. Never touch the washing machine when barefoot or with wet or damp hands or feet. Do not open the detergent dispenser while the appliance is in operation. Do not touch the drain water as it could reach very high temperatures. In the event of a malfunction, do not under any circumstances touch internal parts in order to attempt repairs.
Care and maintenance Cutting off the water or electricity supply GB Turn off the water tap after every wash. This will limit the wear of your appliance's water system and also prevent leaks. Unplug your appliance when cleaning it and during all maintenance operations. Cleaning your appliance The exterior and rubber parts of your appliance can be cleaned with a soft cloth soaked in lukewarm soapy water. Do not use solvents or abrasives.
Troubleshooting Your Washer-dryer could fail to work. Before calling for Assistance (see page 12), make sure the problem can't easily be solved by consulting the following list. The water inlet hose is not connected to the tap. The hose is bent. The water tap is not turned on. There is a water shortage. The water pressure is insufficient. The START/RESET button has not been pressed. The washer-dryer continuously loads and unloads water.
Service Before calling for Assistance: Check whether you can solve the problem on your own (see page 11); Restart the programme to check whether the problem has been solved; If this is not the case, contact an authorised Technical Service Centre on the telephone number provided on the guarantee certificate. GB Always request the assistance of authorised servicemen. Notify the operator of: the type of problem; the appliance model (Mod.); the serial number (S/N).
Instructies voor het gebruik WASDROOGMACHINE Inhoud NL Nederlands NL Installatie, 14-15 Uitpakken en waterpas zetten, 14 Water- en elektrische aansluiting, 14-15 Eerste wasprogramma, 15 Technische gegevens, 15 Beschrijving van de wasdroogmachine, 16-17 Bedieningspaneel, 16 Controlelampjes, 17 Start en programma's, 18 In het kort: een programma starten, 18 Tabel van de programma's, 18 Persoonlijk instellen, 19 WIDL 146 Instellen van de temperatuur, 19 Instellen van het drogen, 19 Functies, 19 Wasmi
Installatie Het is belangrijk dit boekje te bewaren zodat u het kunt raadplegen wanneer u maar wilt. In het geval dat u de machine verkoopt, of u verhuist, moet het boekje bij de machine blijven zodat de nieuwe gebruiker de functies en betreffende raadgevingen kan leren kennen. NL Een correcte waterpas geeft de machine stabiliteit en vermijdt trillingen, lawaai en het zich verplaatsen gedurende het functioneren van de machine.
Aansluiting van de afvoerbuis NL Het snoer mag niet in bochten of geknikt liggen. Installatie 65 - 100 cm Verbind de buis, zonder hem te buigen, aan een afvoerleiding of aan een afvoer in de muur tussen 65 en 100 cm van de grond af; Gebruik geen verlengsnoeren of dubbelstekkers. De voedingskabel mag alleen door een bevoegde installateur worden vervangen. Belangrijk! De fabrikant is niet aansprakelijk wanneer deze normen niet gerespecteerd zijn.
Beschrijving van de wasdroogmachine Bedieningspaneel NL FUNCTIE knoppen Controlelampjes Controlelampje AAN/DEUR GEBLOKKEERD AAN/UIT knop PROGRAMMA knop Wasmiddellaatje START/RESET knop DROOG-knop Wasmiddellaatje: voor wasmiddel en verdere toevoegingen (zie blz. 20). Controlelampjes: voor het volgen van het verloop van het wasprogramma. Als de functie Delay Timer is ingesteld, wordt de resterende tijd aangegeven tot het starten van het programma (zie blz. 17).
Controlelampjes Uitgestelde start ingesteld: Als de functie Delay Timer is geactiveerd (zie blz. 19), nadat het programma is gestart, gaat het controlelampje dat bij de uitgestelde start hoort knipperen: Voorwas / Was Spoelen Drogen - Aan het einde van de droogcycle gaat het knipperen om aan controlelampje van de fase te duiden dat de DROOG-knop op 0 moet worden gezet. Wasmiddel Voorzorgsmaatregelen Funtie-knoppen De FUNCTIE-KNOPPEN dienen ook als controlelampjes.
Start en Programma's In het kort: een programma starten NL 5. Stel indien nodig het drogen in (zie blz. 19). 6. Giet het wasmiddel en verdere toevoegingen in het laatje (zie blz. 20). 7. Start het programma met de START/RESET knop. Voor het annuleren houdt u de START/RESET knop minstens 2 seconden ingedrukt. 8. Aan het einde van het programma gaat het controlelampje AAN/DEUR GEBLOKKEERD knipperen hetgeen betekent dat de deur geopend kan worden.
Persoonlijk instellen C Instellen van de temperatuur Tabel droogtijden Instellen van het drogen Door aan de DROOG-knop te draaien stelt u het gewenste soort drogen in. Er zijn twee mogelijkheden: A - Gebaseerd op de tijdsduur: Van 40 tot 150 minuten. Katoen, linnen Wasgoed van versch. grootte Katoen Handdoeken Terital, katoen Lakens, overhemden Acrylic Nylon Max. lading (kg) Kastdroog Drogen en ophangen Strijkdroog 4 130 120 110 4 130 120 110 2,5 90 80 70 Pyjama's, sokken enz.
Wasmiddel en wasgoed NL Wasmiddellaatje Speciale stukken Een goed resultaat van de was hangt ook af van een juiste dosis wasmiddel: te veel maakt het wassen niet beter en blijft in het wasgoed hangen terwijl het slecht is voor het milieu. Gordijnen: vouw de gordijnen nauwkeurig en doe ze in een kussensloop of net. Was ze apart zonder ooit de halve lading te overschrijden. Gebruik programma 6 dat automatisch de centrifuge uitsluit.
Voorzorgsmaatregelen en raadgevingen De wasdroogmachine is ontworpen en geproduceerd volgens de internationale veiligheidsnormen. Deze aanwijzingen worden voor uw eigen veiligheid gegeven en zij moeten met aandacht worden gelezen. Het afvoeren Algemene veiligheid Het afvoeren van de oude wasdroogmachine: maak hem eerst onbruikbaar door de kabel door te snijden en de deur te verwijderen. Trek de stekker nooit aan het snoer uit het stopcontact, maar altijd door de stekker aan te pakken.
Onderhoud NL Afsluiten van water en stroom Reinigen van de pomp Doe de kraan dicht na iedere wasbeurt. Hiermee reduceert u de kans op lekkage. De wasdroogmachine is voorzien van een zelfreinigende pomp en hoeft dus niet te worden schoongemaakt. Het kan echter gebeuren dat kleine voorwerpen (geldstukken, knopen) in het voorvakje terecht komen dat de pomp beschermt en zich aan de onderkant bevindt.
Storingen en oplossingen Het kan gebeuren dat de machine niet werkt. Voordat u de installateur opbelt (zie blz. 24), controleert u of het een storing betreft die gemakkelijk te verhelpen is met behulp van de volgende lijst. De watertoevoerslang is niet aangesloten aan de kraan. De slang ligt gekneld. De kraan is niet open. In huis mankeert het water. Er is geen voldoende druk. De START/RESET knop is niet ingedrukt. De wasdroogmachine blijft water aan- en afvoeren.
Service Voordat u er de installateur bijhaalt: Kijk eerst even of u het probleem zelf kunt oplossen (zie blz. 23); Start het programma om te controleren of de storing is verholpen; Is dit niet het geval dan neemt u contact op met de bevoegde dichtsbijzijnde Technische Dienst via het telefoonnummer dat op het garantiebewijs/gebruiksaanwijzing staat. NL Nooit een niet-bevoegde installateur erbij halen. Service Vermeld: het soort storing; het model van de machine (Mod.
Bedienungsanleitungen WASCHTROCKNER INHALTSVERZEICHNIS DE Deutsch DE Installation, 26-27 Auspacken und Aufstellen, 26 Wasser- und Elektroanschlüsse, 26-27 Erster Waschgang, 27 Technische Daten, 27 Beschreibung des Waschtrockner, 28-29 Schalterblende, 28 Kontrollleuchten, 29 Inbetriebnahme und Programme, 30 Kurz zusammengefasst: Waschprogramm starten, 30 Programmtabelle, 30 Individualisierungen, 31 WIDL 146 Einstellen der Temperatur, 31 Trockengang einstellen, 31 Funktionen, 31 Waschmittel und Wäsc
Installation DE Es ist äußerst wichtig, diese Bedienungsanleitung sorgfältig aufzubewahren, um sie jederzeit zu Rate ziehen zu können. Sorgen Sie dafür, dass sie im Falle eines Umzugs oder Übergabe an einen anderen Benutzer das Gerät stets begleitet, damit auch der neue Inhaber die Möglichkeit hat, diese zu Rate zu ziehen. Eine präzise Nivellierung verleiht dem Gerät die erforderliche Stabilität, durch die Vibrationen, Betriebsgeräusche und ein Verrücken des Gerätes vermieden werden.
Anschluss des Ablaufschlauches DE Mehrfachstecker. Das Kabel darf nicht gebogen bzw. eingeklemmt werden. Installation 65 - 100 cm Schließen Sie den Ablaufschlauch, ohne ihn dabei zu krümmen, an eine Ablaufleitung, oder an einen in der Wand in einer Mindesthöhe von 65 - 100 cm angelegten Ablauf an; Verwenden Sie bitte keine Verlängerungen oder Das Versorgungskabel darf nur durch autorisierte Fachkräfte ausgetauscht werden. Erster Waschgang Lassen Sie nach der Installation bzw.
Beschreibung des Waschtrockner DE Schalterblende Taste FUNKTIONEN Kontrollleuchten Kontrollleuchte ON/FÜLLFENSTER GESPERRT Taste EIN/AUS Wahlschalter Taste Waschmittelschublade PROGRAMME START/RESET Wahlschalter Wahlschalter TEMPERATUR TROCKNEN Waschmittelschublade: für Waschmittel und Zusätze (siehe Seite 32). Wahlschalter TEMPERATUR: Zur Einstellung der Waschtemperatur oder der Kaltwäsche (siehe Seite 31). Kontrollleuchten: Zur Kontrolle des Waschprogrammablaufs.
Kontrollleuchten DE Installation Die Kontrollleuchten liefern wichtige Hinweise. Sie signalisieren: Laufende Programmphase: Während des Waschprogrammablaufs leuchten die Kontrollleuchten nach und nach auf und zeigen so den jeweiligen Stand an.
Inbetriebnahme und Programme Kurz zusammengefasst: Waschprogramm starten DE 5. Trockengang falls erforderlich einstellen (siehe Seite 31). 6. Waschmittel und Zusätze einfüllen (siehe Seite 32). 7. Programm durch Druck auf die Taste START/RESET in Gang setzen. Um dieses zu löschen, Taste START/RESET für mindestens 2 Sekunden gedrückt halten. 8. Ist das Waschprogramm abgelaufen schaltet die Kontrollleuchte ON/FÜLLFENSTER GESPERRT auf Blinklicht, was anzeigt, dass das Fenster geöffnet werden kann.
Individualisierungen C Einstellen der Temperatur Durch Drehen des Wahlschalters TEMPERATUR wird die Waschtemperatur eingestellt. (siehe Programmtabelle auf Seite 30). Die Temperatur kann bis auf Kaltwäsche ( ) herabgesetzt werden. A rt d e r L ad u n g M ax .
Waschmittel und Wäsche DE Waschmittelschublade Besondere Wäscheteile Ein gutes Waschergebnis hängt auch von einer korrekten Waschmitteldosierung ab: Eine zu hohe Dosierung bedeutet nicht unbedingt reinere Wäsche, sie trägt nur dazu bei, die Maschineninnenteile zu verkrusten und die Umwelt zu belasten. Gardinen:Gardinen zusammengefaltet in einem Kissenbezug oder in einem netzartigen Beutel waschen. Waschen Sie diese allein, ohne das Gesamtgewicht für halbe Füllung zu übersteigen.
Vorsichtsmaßregeln und Hinweise Allgemeine Sicherheit Der Waschtrockner darf nur von Erwachsenen und gemäß den Anleitungen dieses Handbuchs bedient werden. Ziehen Sie den Gerätestecker nicht am Kabel aus der Steckdose, sondern nur am Stecker selbst. Öffnen Sie die Waschmittelschublade nicht, wenn das Gerät in Betrieb ist. Öffnen Sie das Füllfenster nicht mit Gewalt: Der Sicherheits-Schließmechanismus könnte hierdurch beschädigt werden.
Reinigung und Pflege Wasser- und Stromversorgung abstellen DE Wasserhahn nach jedem Waschvorgang zudrehen. Hierdurch wird der Verschleiß der Wasseranlage verringert und Wasserlecks vorgebeugt. Ziehen Sie den Stecker aus der Steckdose, bevor Sie Ihren Waschtrockner reinigen. Reinigung der Pumpe Ihr Gerät ist mit einer selbstreinigenden Pumpe ausgerüstet, eine Wartung ist demnach nicht erforderlich.
Störungen und Abhilfe Es kann immer einmal vorkommen, dass Ihr Waschtrockner nicht funktioniert. Bevor Sie sich an den Technischen Kundendienst wenden (siehe Seite 36), vergewissern Sie sich zuerst, ob es sich nicht um eine Kleinigkeit handelt, die Sie selbst beheben können. Ziehen Sie hierzu nachstehendes Verzeichnis zu Rate. Mögliche Ursachen / Lösungen: Der Waschtrockner schaltet sich nicht ein. Der Stecker steckt nicht in der Steckdose, oder nicht so, dass der Kontakt Der Waschgang startet nicht.
Kundendienst 195043046.00 02/2004 - Xerox Business Services Bevor Sie sich an den Kundendienst wenden: Kontrollieren Sie zuerst, ob das Problem nicht allein gelöst werden kann (siehe Seite 35); Starten Sie das Programm erneut, um sicherzustellen, dass die Störung auch wirklich behoben wurde; Ist dies nicht der Fall, dann kontaktieren Sie den autorisierten Kundendienst unter der auf dem Garantieschein aufgedruckten Telefonnummer. DE Wenden Sie sich auf keinen Fall an nicht autorisierte Techniker.