Instructions for use WASHING MACHINE Contents GB Installation, 2-3 GB English,1 F Français,13 DE Deutsch,25 Unpacking and levelling Connecting the electricity and water supplies The first wash cycle Technical data Care and maintenance, 4 NL Nederlands,37 Cutting off the water or electricity supply Cleaning the washing machine Cleaning the detergent dispenser drawer Caring for the door and drum of your appliance Cleaning the pump Checking the water inlet hose Precautions and tips, 5 WMD 962 General
Installation GB ! Read these instructions carefully: they contain vital information relating to the safe installation and operation of the appliance. venness by tightening or loosening the adjustable front feet (see figure); the angle of inclination, measured in relation to the worktop, must not exceed 2°. Levelling the machine correctly will provide it with stability, help to avoid vibrations and excessive noise and prevent it from shifting while it is operating.
Connecting the drain hose 65 - 100 cm Connect the drain hose, without bending it, to a drain duct or a wall drain situated between 65 and 100 cm from the floor; ! Do not use extension cords or multiple sockets. ! The cable should not be bent or compressed. ! The power supply cable must only be replaced by authorised technicians. Warning! The company shall not be held responsible in the event that these standards are not observed.
Care and maintenance GB Cutting off the water and electricity supplies Caring for the door and drum of your appliance • Turn off the water tap after every wash cycle. This will limit wear on the hydraulic system inside the washing machine and help to prevent leaks. • Always leave the porthole door ajar in order to prevent unpleasant odours from forming. • Unplug the washing machine when cleaning it and during all maintenance work.
Precautions and tips ! This washing machine was designed and constructed in accordance with international safety regulations. The following information is provided for safety reasons and must therefore be read carefully. General safety • This appliance was designed for domestic use only.
Description of the washing machine GB Control panel CLEANING ACTION ON/OFF button button SPIN SPEED button DISPLAY Detergent dispenser drawer WASH CYCLE SELECTOR MY CYCLE button START/PAUSE button with indicator light FUNCTION buttons buttons ANTI ALLERGY RINSE button DELAY TIMER button TEMPERATURE button CHILD LOCK button Detergent dispenser drawer: used to dispense detergents and washing additives (see “Detergents and laundry”).
Display GB Z B A X D C E Y F The display is useful when programming the machine and provides a great deal of information. The two upper strings A and B provide details of the wash cycle selected, the wash cycle phase in progress and all information relating to the progress status of the wash cycle. String C shows the time remaining until the end of the wash cycle in progress and, if a DELAYED START has been set, the time remaining until the start of the selected wash cycle.
Running a wash cycle GB 1. SWITCH THE MACHINE ON. Press the On/Off button ; the text POWER ON will appear on the display and the START/PAUSE indicator light will flash slowly in a green colour. 2. LOAD THE LAUNDRY. Open the porthole door. Load the laundry, making sure you do not exceed the maximum load value indicated in the table of programmes on the following page. 3. MEASURE OUT THE DETERGENT.
Wash cycles and functions Total water lt Cycle duration Max. load (kg) Residual dampness % Energy consumption kWh 40° 1600 60° (Max. 90°) 1600 (3) - - 180’ Fabric softener Anti Stain Cotton Standard 60° (1st press of the button) (1): heavily soiled whites and delicate colours. Cotton Standard 40° (2nd press of the button) (2): lightly soiled whites and delicate colours. Cotton Standard 20° (3rd press of the button): lightly soiled whites and delicate colours. Max. speed (rpm) Bleach Max.
Detergents and laundry GB Detergent dispenser drawer Special wash cycles Good washing results also depend on the correct dose of detergent: adding too much detergent will not necessarily result in a more efficient wash, and may in fact cause a build up on the inside of your appliance and contribute to environmental pollution. ! Use powder detergent for white cotton garments, for pre-washing, and for washing at temperatures over 60°C. ! Follow the instructions given on the detergent packaging.
Troubleshooting Your washing machine could fail to work. Before contacting the Technical Assistance Centre (see “Assistance”), make sure that the problem cannot be solved easily using the following list. GB Problem: Possible causes / Solutions: The washing machine does not switch on. • The appliance is not plugged into the socket fully, or is not making contact. • There is no power in the house. The wash cycle does not start. • • • • • The washing machine door is not closed properly.
Service GB Before calling for Assistance: • Check whether you can solve the problem alone (see “Troubleshooting”); • Restart the programme to check whether the problem has been solved; • If this is not the case, contact an authorised Technical Assistance Centre using the telephone number provided on the guarantee certificate. ! Always request the assistance of authorised technicians. Have the following information to hand: • the type of problem; • the appliance model (Mod.); • the serial number (S/N).
Mode d’emploi LAVE-LINGE Sommaire FR Français FR Installation, 14-15 Déballage et mise à niveau Raccordements eau et électricité Premier cycle de lavage Caractéristiques techniques Entretien et soin, 16 Coupure de l’arrivée d’eau et du courant Nettoyage du lave-linge Nettoyage du tiroir à produits lessiviels.
Installation FR ! Conserver ce mode d’emploi pour pouvoir le consulter à tout moment. En cas de vente, de cession ou de déménagement, veiller à ce qu’il suive toujours le lave-linge pour que son nouveau propriétaire soit informé sur son mode de optionnement et puisse profiter des conseils correspondants. Une bonne mise à niveau garantit la stabilité de l’appareil et évite qu’il y ait des vibrations, du bruit et des déplacements en cours de optionnement.
Raccordement du tuyau de vidange 65 - 100 cm Raccorder le tuyau d’évacuation, sans le plier, à un conduit d’évacuation ou à une évacuation murale placés à une distance du sol comprise entre 65 et 100 cm ; ou bien l’accrocher à un évier ou à une baignoire, dans ce cas, fixer le support en plastique fourni avec l’appareil au robinet (voir figure). L’extrémité libre du tuyau d’évacuation ne doit pas être plongée dans l’eau.
Entretien et soin FR Coupure de l’arrivée d’eau et du courant • Fermer le robinet de l’eau après chaque lavage. Cela réduit l’usure de l’installation hydraulique du lave-linge et évite tout danger de fuites. • Débrancher la fiche de la prise de courant lors de tout nettoyage du lave-linge et pendant tous les travaux d’entretien. Nettoyage du lave-linge • Pour nettoyer l’extérieur et les parties en caoutchouc, utiliser un chiffon imbibé d’eau tiède et de savon. N’utiliser ni solvants ni abrasifs.
Précautions et conseils ! Ce lave-linge a été conçu et fabriqué conformément aux normes internationales de sécurité. Ces consignes sont fournies pour des raisons de sécurité, il faut les lire attentivement. Sécurité générale • Cet appareil est conçu pour un usage domestique.
Description du lave-linge FR Bandeau de commandes Touche MY CYCLE Touche Touche INTENSITE DE LAVAGE ON/OFF Touche ESSORAGE Écran Touche avec voyant Touches Tiroir à produits lessiviels START/PAUSE Touches SÉLECTEUR PROGRAMMES FONCTION Touche TEMPÉRATURE Touche ANTIALLERGIES Touche DÉPART DIFFÉRÉ Touche VERROUILLAGE TOUCHES Tiroir à produits lessiviels: pour charger les produits lessiviels et les additifs (voir “Produits lessiviels et linge”).
Écran FR Z B A X D C E Y F L’écran est utile pour programmer la machine et fournit de multiples renseignements. Les deux chaînes supérieures A et B affichent : le programme de lavage sélectionné, la phase de lavage en cours et toutes les indications relatives au déroulement du programme. La chaîne C affiche le temps restant à la fin du cycle de lavage en cours et si un DÉPART DIFFÉRÉ a été sélectionné, le temps restant avant le démarrage du programme sélectionné.
Comment faire un cycle de lavage FR 1. METTRE L’APPAREIL SOUS TENSION. Appuyer sur la touche , l’inscription BONJOUR s’affiche à l’écran ; le voyant de START/PAUSE passe au vert et clignote lentement. 2. CHARGER LE LINGE. Ouvrir la porte hublot. Charger le linge en faisant attention à ne pas dépasser la quantité indiquée dans le tableau des programmes de la page suivante. 3. DOSER LE PRODUIT LESSIVIEL.
Programmes et fonctions Humidité résiduelle % Consommation d’énergie kWh Eau totale lt Durée cycle résistantes très sales. Charge maxi (Kg) Coton Standard 60° (1) (1° pression de la touche): blancs et couleurs - 5 - - - 180’ 9 44 1,36 57,5 205’ Produits lessiviels 40° 1600 60° (Max. 90°) 1600 (3) Anti taches Javel Description du Programme Vitesse maxi (tours minute) Assouplissant Temp. maxi.
Produits lessiviels et linge FR Tiroir à produits lessiviels Programmes spéciaux Un bon résultat de lavage dépend aussi d’un bon dosage de produit lessiviel: un excès de lessive ne lave pas mieux, il incruste l’intérieur du lave-linge et pollue l’environnement. Anti-taches: ce programme est idéal pour le lavage de linge très sale, aux couleurs résistantes. Il assure une classe de lavage supérieure à la classe standard (classe A). Ce programme ne permet pas de mélanger du linge de couleurs différentes.
Anomalies et remèdes Il peut arriver que le lave-linge ne fonctionne pas bien. Avant d’appeler le Service de dépannage (voir “Assistance”), contrôler s’il ne s’agit pas par hasard d’un problème facile à résoudre à l’aide de la liste suivante. Anomalies: Causes / Solutions possibles: Le lave-linge ne s’allume pas. • La fiche n’est pas branchée dans la prise de courant ou mal branchée. • Il y a une panne de courant. Le cycle de lavage ne démarre pas. • • • • • Le hublot n’est pas bien fermé.
Assistance FR Avant d’appeler le service après-vente: • Vérifier si on ne peut pas résoudre l’anomalie par ses propres moyens (voir “Anomalies et Remèdes”); • Remettre le programme en marche pour contrôler si l’inconvénient a disparu; • Autrement, contacter le Centre d’Assistance technique agréé au numéro de téléphone indiqué sur le certificat de garantie. ! Ne jamais s’adresser à des techniciens non agréés. Communiquer: • le type de panne; • le modèle de l’appareil (Mod.); • son numéro de série (S/N).
Bedienungsanleitungen WASCHVOLLAUTOMAT INHALTSVERZEICHNIS DE Installation, 26-27 DE Deutsch Auspacken und Aufstellen Wasser- und Elektroanschlüsse Erster Waschgang Technische Daten Reinigung und Pflege, 28 Abstellen der Wasser- und Stromversorgung Reinigung des Gerätes Reinigung der Waschmittelschublade Pflege der Gerätetür und Trommel Reinigung der Pumpe Kontrolle des Wasserzulaufschlauchs Vorsichtsmaßregeln und Hinweise, 29 WMD 962 Allgemeine Sicherheit Entsorgung Manuelles Öffnen der Gerätetür Be
Installation DE ! Es ist äußerst wichtig, diese Bedienungsanleitung sorgfältig aufzubewahren, um sie jederzeit zu Rate ziehen zu können. Sorgen Sie dafür, dass sie im Falle eines Umzugs oder einer Übergabe an einen anderen Benutzer das Gerät stets begleitet, damit auch der neue Inhaber die Möglichkeit hat, diese zu Rate zu ziehen. ! Lesen Sie bitte folgende Hinweise aufmerksam durch: sie liefern wichtige Informationen hinsichtlich der Installation, des Gebrauchs und der Sicherheit.
Anschluss des Ablaufschlauches 65 - 100 cm Schließen Sie den Ablaufschlauch, ohne ihn dabei zu knicken, an eine Ablaufleitung, oder an einen in der Wand, in einer Höhe von 65cm bis 100cm an; ! Verwenden Sie bitte keine Verlängerungen oder Mehrfachstecker. ! Das Netzkabel darf nicht gebogen bzw. eingeklemmt werden. ! Das Versorgungskabel darf nur durch autorisierte Fachkräfte ausgetauscht werden. Achtung! Der Hersteller übernimmt keinerlei Haftung, sollten diese Vorschriften nicht genau beachtet werden.
Reinigung und Pflege DE Abstellen der Wasser- und Stromversorgung Pflege der Gerätetür und Trommel • Drehen Sie den Wasserhahn nach jedem Waschvorgang zu. Hierdurch wird der Verschleiß der Wasseranlage verringert und Wasserlecks vorgebeugt. • Ziehen Sie den Netzstecker aus der Steckdose, bevor Sie Ihren Waschvollautomaten reinigen. Reinigung der Pumpe Reinigung des Gerätes • Die Gehäuseteile und die Teile aus Gummi können mit einem mit warmer Spülmittellauge angefeuchteten Tuch gereinigt werden.
Vorsichtsmaßregeln und Hinweise ! Der Waschvollautomat wurde nach den strengsten internationalen Sicherheitsvorschriften entworfen und gebaut. Nachstehende Hinweise werden aus Sicherheitsgründen geliefert und sollten aufmerksam gelesen werden. Allgemeine Sicherheit • Dieses Gerät wurde ausschließlich für den Einsatz im privaten Haushalt konzipiert.
Beschreibung Ihres Waschvollautomaten DE Bedienblende Taste Taste ON/OFF WASCHINTENSITÄT Taste SCHLEUDERN DISPLAY Tasten Waschmittelschublade PROGRAMMWAHL FUNKTIONEN MY CYCLE Taste SPÜLINTENSITÄT Taste STARTZEITVORWAHL Waschmittelschublade: für Waschmittel und Zusätze (siehe „Waschmittel und Wäsche“). Taste ON/OFF : Drücken Sie kurz auf die Taste, um das Gerät ein- bzw. auszuschalten. Die Kontrollleuchte START/ PAUSE, die langsam grün blinkt, zeigt an, dass das Gerät eingeschaltet ist.
Display Z B DE A X D C E Y F Das Display dient nicht nur zur Programmierung des Gerätes, sondern liefert auch zahlreiche Informationen. In den beiden oberen Zeilenreihen A und B werden das ausgewählte Waschprogramm, die laufende Waschphase und alle Angaben zum Programmfortschritt angezeigt. In der Zeilenreihe C werden die Restzeit bis zum Ende des laufenden Waschvorgangs und bei Einstellung einer STARTZEITVORWAHL die bis zum Start des ausgewählten Programms verbleibende Zeit angezeigt.
Durchführung eines Waschprogramms DE 1. EINSCHALTEN DES GERÄTES. Drücken Sie auf die Taste , woraufhin auf dem Display die Meldung POWER EIN erscheint; die Kontrollleuchte START/PAUSE blinkt langsam grün. 2. EINFÜLLEN DER WÄSCHE. Öffnen Sie die Gerätetür. Füllen Sie die Wäsche ein. Achten Sie hierbei bitte darauf, die in der Programmtabelle (auf der nächsten Seite) angegebene Wäschemenge nicht zu überschreiten. 3. DOSIERUNG DES WASCHMITTELS.
Programme und Funktionen Wasser gesamt lt Programmdauer Flecken 1600 40° 60° Baumwolle 60° (1) (erster Tastendruck): stark verschmutzte Weiß1600 (3) und farbechte Buntwäsche. (Max. 90°C) Baumwolle 40° (2) (zweiter Tastendruck): leicht verschmutzte 1600 40° Weißwäsche und empfindliche Buntwäsche. Baumwolle 20° (dritter Tastendruck): leicht verschmutzte Weißwä1600 20° sche und empfindliche Buntwäsche. Synthetik Robust (erster Tastendruck): stark verschmutzte, far 800 60° bechte Buntwäsche.
Waschmittel und Wäsche DE Waschmittel und Wäsche Sonderprogramme Ein gutes Waschergebnis hängt auch von einer korrekten Waschmitteldosierung ab: Eine zu hohe Dosierung bedeutet nicht unbedingt reinere Wäsche, sie trägt nur dazu bei, die Maschineninnenteile zu verkrusten und die Umwelt zu belasten. Flecken: das Programm ist für die Reinigung stark verschmutzter Kleidung mit widerstandsfähigen Farben geeignet. Das Programm gewährleistet einen Waschgang, der besser als der Standard (Klasse A) ist.
Störungen und Abhilfe Bei Funktionsstörung: Bevor Sie sich an den Technischen Kundendienst wenden (siehe „Kundendienst“), vergewissern Sie sich zuerst, ob es sich nicht um eine Kleinigkeit handelt, die Sie selbst beheben können. Ziehen Sie hierzu nachstehendes Verzeichnis zu Rate. Störungen: Mögliche Ursachen / Lösungen: Der Waschvollautomat schaltet sich nicht ein. • Der Stecker steckt nicht in der Steckdose, oder nicht so, dass der Kontakt hergestellt wird. • Der Strom ist ausgefallen.
Kundendienst DE Bevor Sie sich an den Kundendienst wenden: • Sollten einige Kontrollen vorab selbst durchgeführt werden (siehe „Störungen und Abhilfe“); • Starten Sie daraufhin das Programm erneut, um sicherzustellen, dass die Störung auch wirklich behoben wurde; • Ist dies nicht der Fall, dann kontaktieren Sie den autorisierten Kundendienst unter der auf dem Garantieschein befindlichen Telefonnummer. ! Wenden Sie sich auf keinen Fall an nicht autorisierte Techniker.
Gebruiksaanwijzing WASAUTOMAAT Inhoud NL Installatie, 38-39 NL Nederlands Uitpakken en waterpas zetten Hydraulische en elektrische aansluitingen Eerste wascyclus Technische gegevens Onderhoud en verzorging, 40 Afsluiten van water en stroom Reinigen van de wasautomaat Reinigen van het wasmiddelbakje Onderhoud van deur en trommel Reinigen van de pomp Controleren van de buis van de watertoevoer Voorzorgsmaatregelen en advies, 41 WMD 962 Algemene veiligheid Afvalverwijdering Handmatige opening van de deu
Installatie NL ! Het is belangrijk deze handleiding te bewaren voor latere raadpleging. In het geval u het apparaat verkoopt, of u verhuist, moet het boekje bij de wasautomaat blijven zodat de nieuwe gebruiker de functies en betreffende raadgevingen kan doornemen. ! Lees de instructies aandachtig door: u vindt er belangrijke informatie betreffende installatie, gebruik en veiligheid. Uitpakken en waterpas zetten Uitpakken 1. De wasautomaat uitpakken. 2.
Aansluiting van de afvoerbuis 65 - 100 cm Verbind de buis, zonder hem te buigen, aan een afvoerleiding of aan een afvoer in de muur tussen de 65 en 100 cm van de grond af; of hang hem aan de rand van een wasbak of badkuip, en bind de bijgeleverde steun aan de kraan (zie afbeelding). Het uiteinde van de afvoerslang mag niet onder water hangen.
Onderhoud en verzorging NL Afsluiten van water en stroom Reinigen van de pomp • Sluit na iedere wasbeurt de kraan af. Hiermee beperkt u slijtage van de waterinstallatie van de wasmachine en voorkomt u lekkage. • Sluit altijd eerst de stroom af voordat u de wasautomaat gaat schoonmaken en gedurende onderhoudswerkzaamheden. De wasautomaat is voorzien van een zelfreinigende pomp en hoeft dus niet te worden onderhouden.
Voorzorgsmaatregelen en advies ! De wasmachine is ontworpen en geproduceerd volgens de internationale veiligheidsnormen. Deze aanwijzingen zijn voor uw eigen veiligheid geschreven en moeten aandachtig worden doorgenomen. Handmatige opening van de deur Mocht er in het huis geen stroom aanwezig zijn en u wilt het deurtje openen om de was op te hangen, dan dient u het volgende te doen: Algemene veiligheid • Dit apparaat is uitsluitend ontworpen voor huishoudelijk niet-professioneel gebruik.
Beschrijving van de wasautomaat NL Bedieningspaneel SCHOONMAAK ACTIE ON/OFF toets toets CENTRIFUGE toets DISPLAY Toetsen Wasmiddelbakje PROGRAMMAKEUZE MY CYCLE toets SOORT SPOELING toets UITGESTELDE START toets Toets met controlelampje FUNCTIETOETSEN START/PAUSE TEMPERATUUR toets TOETSBLOKKERING toets Wasmiddelbakje: voor wasmiddelen en wasversterkers (zie “Wasmiddelen en wasgoed”). Toets TEMPERATUUR : druk hierop om de temperatuur te verlagen: de waarde wordt op het display aangegeven.
Display Z B NL A X D C E Y F Het display is nodig om de wasautomaat te programmeren en geeft meerdere soorten informatie. In de twee bovenste vakken A en B verschijnen het geselecteerde wasprogramma, de lopende wasfase en alle aanwijzingen met betrekking tot het verloop van het wasprogramma. In het vak C verschijnt de resterende tijd tot het einde van de wascyclus. Indien een UITGESTELDE START is geselecteerd verschijnt de resterende tijd tot aan de start van het geselecteerde wasprogramma.
Het uitvoeren van een wascyclus NL 1. DE WASAUTOMAAT AANZETTEN. Druk op de toets , op het display verschijnt de tekst AANZETTEN. Het groene controlelampje START/PAUSE zal langzaam knipperen. 2. HET WASGOED INLADEN. Open de deur. Laad het wasgoed in en zorg ervoor nooit de laadhoeveelheid te overschrijden aangegeven in de programmatabel op de volgende bladzijde. 3. WASMIDDEL DOSEREN. Trek het bakje naar buiten en doe het wasmiddel in de speciale bakjes, zoals aangegeven in “Wasmiddelen en wasgoed”. 4.
Programma’s en functies Energieverbruik % Energieverbruik kWh Totaal water lt Duur cyclus 40° 1600 60° 1600 (Max. 90°C) (3) NL Maximale lading (kg) Vlekkenverwijdering Standaard Katoen 60° (1) (1e druk op de toets): zeer vuile wit en kleurecht bont wasgoed. Standaard Katoen 40° (2) (2e druk op de toets): niet zo vuile witte en bonte fijne was. Standaard Katoen 20° (3e druk op de toets): niet zo vuile witte en bonte fijne was.
Wasmiddelen en wasgoed NL Wasmiddelbakje Speciale programma’s Een goed wasresultaat hangt ook af van de juiste dosis wasmiddel: te veel wasmiddel maakt het wassen niet beter. Het wasmiddel blijft aan de binnenzijde van de wasautomaat zitten en zorgt voor het vervuilen van het milieu. ! Gebruik waspoeder voor witte katoenen was, voor de voorwas en voor het wassen op temperaturen van meer dan 60°C. ! Volg de aanwijzingen op de wasmiddelverpakking.
Storingen en oplossingen Het kan gebeuren dat de wasautomaat niet werkt. Voor u contact opneemt met de Servicedienst (zie “Service”) moet u controleren of het niet een storing betreft die u zelf makkelijk kunt verhelpen met behulp van de volgende lijst. Storingen: Mogelijke oorzaken / Oplossing: De wasautomaat gaat niet aan. • De stekker zit niet in het stopcontact of niet ver genoeg om contact te maken. • Het hele huis zit zonder stroom. De wascyclus start niet.
Service 195116658.00 07/2013 - Xerox Fabriano NL Voordat u de Servicedienst inschakelt: • Controleer eerst of u het probleem zelf kunt oplossen (zie “Storingen en oplossingen”). • Start het programma opnieuw om te controleren of de storing is verholpen; • Als dit niet het geval is moet u contact opnemen met de erkende Technische Servicedienst via het telefoonnummer dat op het garantiebewijs staat. ! Wendt u nooit tot een niet erkende installateur.