User's Manual

CAS-GPS Node II User
Manual
CAS-GPS Node II User Manual (DOCU0142) Rev D Page 19 of 21
13 REGULATORY INFORMATION
Warning: Modifications to this product without written consent from the manufacturer or its designated authorised
representatives could void the user’s authority to operate the equipment
13.1 DECLARATION OF CONFORMITY WITH FCC RULES FOR ELECTROMAGNETIC COMPATIBILITY
Supplier's Declaration of Conformity
47 CFR § 2.1077 Compliance Information
MAKE: CAS-GPS NODE
FCC ID: YIY-PROD11162
Unique Identifier: PROD1116-L2, CAS-GPS LIGHT VEHICLE NODE REGION 2
PROD1116-E2, CAS-GPS LIGHT VEHICLE EXPANDABLE NODE REGION 2
PROD1116-S2, CAS-GPS TYPE S NODE REGION 2
PROD1116-P2, CAS-GPS TYPE P NODE REGION 2
PROD1116-L2X, CAS-GPS LIGHT VEHICLE NODE REGION 2 XTD
PROD1116-E2X, CAS-GPS LIGHT VEHICLE EXPANDABLE NODE REGION 2 XTD
PROD1116-S2X, CAS-GPS TYPE S NODE REGION 2 XTD
PROD1116-P2X, CAS-GPS TYPE P NODE REGION 2 XTD
PROD1116-L2NT, CAS-GPS LIGHT VEHICLE NODE REGION 2 NO ToF
PROD1116-E2NT, CAS-GPS LIGHT VEHICLE EXPANDABLE NODE REGION 2 NO ToF
PROD1116-S2NT, CAS-GPS TYPE S NODE REGION 2 NO ToF
PROD1116-P2NT, CAS-GPS TYPE P NODE REGION 2 NO ToF
PROD1116-L2XNT, CAS-GPS LIGHT VEHICLE NODE REGION 2 XTD NO ToF
PROD1116-E2XNT, CAS-GPS LIGHT VEHICLE EXPANDABLE NODE REGION 2 XTD NO ToF
PROD1116-S2XNT, CAS-GPS TYPE S NODE REGION 2 XTD NO ToF
PROD1116-P2XNT, CAS-GPS TYPE P NODE REGION 2 XTD NO ToF
PROD1151, CAS-GPS LIGHT VEHICLE INTERFACE
PROD1044, CAS-GPS ACTIVE SCREEN 5”
PROD1155, LV DISPLAY MICRO USB TO SERIAL CABLE ASSEMBLY
PROD1155-P, LV DISPLAY MICRO USB POWER SUPPLY
PROD1150, CAS-GPS LIGHT VEHICLE DISPLAY UNIT
All PROD1116 Models contains FCC Approved Module: FCC ID: PVH0965, Model No.: ODIN-W262, Stand-alone IoT Gateway module
(Bluetooth
©
/WLAN)
Responsible Party: GE Digital Mining
2901 East Lake Road
Erie, PA
16531
[phone]
FCC Compliance Statement:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
13.1.1 FCC Interference Statement for Class B devices.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
 Reorient or relocate the receiving antenna.
 Increase the separation between the equipment and receiver.
 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
 Consult the dealer or an experienced radio/TV technician for help.