Datasheet

ManualsBrandsINFINEON TECHNOLOGIES ManualsPMICsPMIC - gate drivers IR 2136 Inverting Half-bridge SOIC 28

Typical Connection

3-PHASE BRIDGE DRIVER

Features

•

Floating channel designed for bootstrap operation

Fully operational to +600V

Tolerant to negative transient voltage - dV/dt immune

•

Gate drive supply range from 10 to 20V (IR2136/IR21368),

11.5 to 20V (IR21362) or 12 to 20V (IR21363/IR21365/

IR21366/IR21367)

•

Undervoltage lockout for all channels

•

Over-current shutdown turns off all six drivers

•

Independent 3 half-bridge drivers

•

Matched propagation delay for all channels

•

Cross-conduction prevention logic

•

Lowside outputs out of phase with inputs. High side

outputs out of phase (IR2136/IR21363/IR21365/

IR21366/IR21367/IR21368) or in phase

(IR21362) with inputs.

•

3.3V logic compatible

•

Lower di/dt gate driver for

better noise immunity

•

Externally programmable

delay for automatic fault

clear

•

Also available LEAD-FREE

Data Sheet No. PD60166 revS

IR2136/IR21362/IR21363/IR21365/

IR21366/IR21367/IR21368

(

S) & (PbF)

www.irf.com 1

(Refer to Lead Assign-

ments for correct pin con-

figuration). This/These

diagram(s) show electri-

cal connections only.

Please refer to our Appli-

cation Notes and

DesignTips for proper cir-

cuit board layout.

Packages

28-Lead PDIP

28-Lead SOIC

44-Lead PLCC w/o 12 leads

Description

The IR2136/IR21362/IR21363/IR21365/IR21366/IR21367/IR21368(J&S) are high votage, high speed power MOSFET

and IGBT drivers with three independent high and low side referenced output channels for 3-phase applications.

Proprietary HVIC technology enables ruggedized monolithic construction. Logic inputs are compatible with CMOS

or LSTTL outputs, down to 3.3V logic. A current trip function which terminates all six outputs can be derived from

an external current sense resistor. An enable function is available to terminate all six outputs simultaneously. An

open-drain FAULT signal is provided to indicate that an overcurrent or undervoltage shutdown has occurred.

Overcurrent fault conditions are cleared automatically after a delay programmed externally via an RC network

connected to the RCIN input. The output drivers feature a high pulse current buffer stage designed for minimum

driver cross-conduction. Propagation delays are matched to simplify use in high frequency applications. The

floating channel can be used to drive N-channel power MOSFETs or IGBTs in the high side configuration which

operates up to 600 volts.

VCC

HIN1,2,3 / HIN1,2,3

LIN1,2,3

FAULT

ITRIP

RCIN

VSS COM

LO1,2,3

VS1,2,3

HO1,2,3

VB1,2,3

IR2136(2)(3)(5)(6)(7)(8)

LOAD

VCC

HIN1,2,3 / HIN1,2,3

LIN1,2,3

FAULT

GND

up to 600V

Part

Input Logic

Ton (typ.)

Toff (typ.)

(typ.)

Vitrip+

UV CC/BS+

UV CC/BS-

IR2136

HIN, LIN

400ns

380ns

2.7V

1.7V

0.46V

8.9V

8.2V

IR21362

HIN/LIN

400ns

380ns

2.7V

1.7V

0.46V

10.4V

9.4V

IR21363

HIN, LIN

400ns

380ns

2.7V

1.7V

0.46V

11.2V

11.0V

IR21365

HIN, LIN

400ns

380ns

2.7V

1.7V

4.3V

11.2V

11.0V

IR21366

HIN, LIN

250ns

180ns

2.0V

1.3V

0.46V

11.2V

11.0V

IR21367

HIN, LIN

250ns

180ns

2.0V

1.3V

4.3V

11.2V

11.0V

IR21368

HIN,LIN

400ns

380ns

2.0V

1.3V

4.3V

8.9V

8.2V

Feature Comparison: IR2136/IR21362/IR21363/

IR21365/IR21366/IR21367/IR21368

Summary of content (36 pages)

PAGE 1
Data Sheet No. PD60166 revS IR2136/IR21362/IR21363/IR21365/ IR21366/IR21367/IR21368 (J&S) & (PbF) 3-PHASE BRIDGE DRIVER Features • • • • • • • • • • • • Floating channel designed for bootstrap operation Packages Fully operational to +600V Tolerant to negative transient voltage - dV/dt immune Gate drive supply range from 10 to 20V (IR2136/IR21368), 11.
PAGE 2
IR2136(2)(3)(5)(6)(7)(8)(J&S) & (PbF) Absolute Maximum Ratings Absolute maximum ratings indicate sustained limits beyond which damage to the device may occur. All voltage parameters are absolute voltages referenced to COM. The thermal resistance and power dissipation ratings are measured under board mounted and still air conditions.
PAGE 3
IR2136(2)(3)(5)(6)(7)(8)(J&S) & (PbF) Recommended Operating Conditions cont. The Input/Output logic timing diagram is shown in figure 1. For proper operation the device should be used within the recommended conditions. All voltage parameters are absolute referenced to COM. The VS offset rating is tested with all supplies biased at 15V differential. Symbol VITRIP VIN TA Min. Max.
PAGE 4
IR2136(2)(3)(5)(6)(7)(8)(J&S) & (PbF) Static Electrical Characteristics cont. VBIAS (VCC, VBS1,2,3) = 15V unless otherwise specified. The VIN, VTH and IIN parameters are referenced to VSS and are applicable to all six channels (HS1,2,3 and LS1,2,3). The VO and IO parameters are referenced to COM and VS1,2,3 and are applicable to the respective output leads: HO1,2,3 and LO1,2,3. Symbol VCCUVVBSUVVCCUVH VBSUVH ILK IQBS IQCC Definition Min. Typ. Max.
PAGE 5
IR2136(2)(3)(5)(6)(7)(8)(J&S) & (PbF) Dynamic Electrical Characteristics VCC = VBS = VBIAS = 15V, VS1,2,3 = VSS = COM, TA = 25oC and CL = 1000 pF unless otherwise specified. Symbol ton Definition Min. Turn-on propagation delay IR2136(2)(3)(5)(8) IR21366(7) toff Turn-off propagation delay IR2136(2)(3)(5)(8) IR21366(7) tr Turn-on rise time tf tEN Turn-off fall time ENABLE low to output IR2136(2)(3)(5)(8) shutdown propagation delay tITRIP tbl IR21366(7) Typ. Max.
PAGE 6
IR2136(2)(3)(5)(6)(7)(8)(J&S) & (PbF) Functional Block Diagram HIN1 INPUT NOISE FILTER LIN1 INPUT NOISE FILTER HIN2 INPUT NOISE FILTER LIN2 INPUT NOISE FILTER HIN3 INPUT NOISE FILTER LIN3 INPUT NOISE FILTER IR2136/21363/21365 DEADTIME & SHOOT-THROUGH PREVENTION VSS/COM LEVEL SHIFTER HV LEVEL SHIFTER VB1 SET RESET LATCH DRIVER UV DETECT VS1 VB2 DEADTIME & SHOOT-THROUGH PREVENTION VSS/COM LEVEL SHIFTER HV LEVEL SHIFTER SET RESET LATCH DRIVER UV DETECT HO2 VS2 VB3 DEADTIME & SHOOT-THR
PAGE 7
IR2136(2)(3)(5)(6)(7)(8)(J&S) & (PbF) Functional Block Diagram HIN1 INPUT NOISE FILTER LIN1 INPUT NOISE FILTER HIN2 INPUT NOISE FILTER LIN2 INPUT NOISE FILTER HIN3 INPUT NOISE FILTER LIN3 INPUT NOISE FILTER IR21362 VB1 VSS/COM LEVEL SHIFTER DEADTIME & SHOOT-THROUGH PREVENTION HV LEVEL SHIFTER SET RESET LATCH DRIVER UV DETECT VS1 VB2 VSS/COM LEVEL SHIFTER DEADTIME & SHOOT-THROUGH PREVENTION HV LEVEL SHIFTER SET RESET LATCH DRIVER UV DETECT HO2 VS2 VB3 VSS/COM LEVEL SHIFTER DEADTIM
PAGE 8
IR2136(2)(3)(5)(6)(7)(8)(J&S) & (PbF) Functional Black Diagram IR21366/IR21367/IR21368 HIN1 DEADTIME & SHOOT-THROUGH PREVENTION LIN1 VSS/COM LEVEL SHIFTER VB1 HV LEVEL SHIFTER SET RESET LATCH DRIVER UV DETECT HO1 VS1 VB2 HIN2 DEADTIME & SHOOT-THROUGH PREVENTION LIN2 VSS/COM LEVEL SHIFTER HV LEVEL SHIFTER SET RESET LATCH DRIVER UV DETECT HO2 VS2 VB3 HIN3 DEADTIME & SHOOT-THROUGH PREVENTION LIN3 VSS/COM LEVEL SHIFTER HV LEVEL SHIFTER SET RESET LATCH DRIVER UV DETECT VS3 VSS VCC INPU
PAGE 9
IR2136(2)(3)(5)(6)(7)(8)(J&S) & (PbF) Lead Definitions Symbol Description VCC Low side and logic fixed supply VSS Logic Ground HIN1,2,3 Logic inputs for high side gate driver outputs (HO1,2,3), out of phase (IR2136/IR21363(5)(6)(7)(8) HIN1,2,3 Logic inputs for high side gate driver outputs (HO1,2,3), in phase (IR21362) LIN1,2,3 FAULT Logic inputs for low side gate driver outputs (LO1,2,3), out of phase Indicates over-current (ITRIP) or low-side undervoltage lockout has occured.
PAGE 10
IR2136(2)(3)(5)(6)(7)(8)(J&S) & (PbF) VS1 26 HIN3 25 5 LIN1 VB2 24 6 LIN2 HO2 23 7 LIN3 8 FAULT 9 ITRIP VB3 20 10 VS1 HIN2 4 HO1 3 VB1 HO1 27 VCC VB1 28 HIN1 HIN1 VCC HIN2 1 2 HIN3 Lead Assignments 6 5 4 3 43 42 41 7 LIN1 8 LIN2 9 37 VB2 LIN3 10 36 HO2 VS2 22 IR2136 11 21 EN HO3 19 11 RCIN VS3 18 12 VSS 13 COM LO1 16 14 LO3 LO2 15 FAULT 35 13 ITRIP 14 15 EN 31 16 30 VB3 5 LIN1 VB2 24 6 LIN2 HO2 23 7 LIN3 8 FAULT 9 ITRI
PAGE 11
IR2136(2)(3)(5)(6)(7)(8)(J&S) & (PbF) HIN1,2,3 HIN1,2,3 LIN1,2,3 EN ITRIP FAULT RCIN HO1,2,3 LO1,2,3 Figure 1. Input/Output Timing Diagram LIN1,2,3 50% 50% 50% HIN1,2,3 EN PW IN ten LIN1,2,3 50% 50% HIN1,2,3 HO1,2,3 ton tr toff tf PW OUT HO1,2,3 LO1,2,3 90% 10% LO1,2,3 90% 10% Figure 2. Switching Time Waveforms www.irf.com 90% Figure 3.
PAGE 12
IR2136(2)(3)(5)(6)(7)(8)(J&S) & (PbF) LIN1,2,3 HIN1,2,3 LIN1,2,3 50% 50% 50% 50% HIN1,2,3 50% LO1,2,3 50% DT HO1,2,3 DT 50% 50% Figure 4. Internal Deadtime Timing Waveforms Vrcin,th+ RCIN ITRIP FAULT 50% 50% 50% tflt 50% 90% Any output tfltclr titrip Figure 5. ITRIP/RCIN Timing Waveforms HIN/LIN on off t in,fil on off U t in,fil on off high HO/LO low Figure 5.5 Input Filter Function 12 www.irf.
PAGE 13
IR2136(2)(3)(5)(6)(7)(8)(J&S) & (PbF) 1000 Turn-on Propagation Delay (ns) Turn-on Propagation Delay (ns) 1000 800 600 M ax. 400 Typ. M in. 200 0 800 M ax. 600 Typ. 400 M in. 200 0 -50 -25 0 25 50 75 100 10 125 12 14 Temperature ( C) 18 20 Figure 6B. Turn-on Propagation Delay vs. Supply Voltage Figure 6A. Turn-on Propagation Delay vs. Temperature 1000 Turn-off Propagation Delay (ns) 1000 Turn-on Propagation Delay (ns) 16 Supply Voltage (V) o 800 M ax. 600 Typ. 400 M in.
PAGE 14
IR2136(2)(3)(5)(6)(7)(8)(J&S) & (PbF) 1000 Turn-off Propagation Delay (ns) Turn-off Propagation Delay (ns) 1000 800 M ax. 600 Typ. 400 M in. 200 800 M ax. 600 Typ. 400 M in. 200 0 0 10 12 14 16 18 3 20 3.5 Figure 7B. Turn-off Propagation Delay vs. Supply Voltage 4.5 5 Figure 7C. Turn-off Propagation Delay vs. Input Voltage 400 400 300 300 Turn-on Rise Time (ns) Turn-on Rise Time (ns) 4 Input Voltage (V) Supply Voltage (V) 200 M ax. 100 M ax. 200 Typ. 100 Typ.
PAGE 15
200 200 150 150 Turn-off Fall Time (ns) Turn-off Fall Time (ns) IR2136(2)(3)(5)(6)(7)(8)(J&S) & (PbF) 100 M ax. 50 100 M ax. Typ. 50 Typ. 0 0 -50 -25 0 25 50 75 100 10 125 12 16 18 20 Figure 9B. Turn-off Fall Time vs. Supply Voltage Figure 9A. Turn-off Fall Time vs. Temperature 1000 EN to Output Shutdown Time (ns) 1000 EN to Output Shutdown Time (ns) 14 Supply Voltage (V) Temperature (oC) 800 600 M ax. Typ. 400 M in. 200 800 M ax. 600 Typ. 400 M in.
PAGE 16
IR2136(2)(3)(5)(6)(7)(8)(J&S) & (PbF) 1500 ITRIP to Output Shutdown Time (ns) EN to Output Shutdown Time (ns) 1000 800 M ax. 600 Typ. 400 M in. 200 0 3 3.5 4 4.5 1200 M ax. 900 Typ. 600 M in. 300 0 -50 5 -25 0 EN Voltage (V) ITRIP to FAULT Indication Time (ns) ITRIP to Output Shutdown Time (ns) M ax. M in. 300 0 10 12 14 16 18 Supply Voltage (V) Figure 11B. ITRIP to Output Shutdown Time vs. Supply Voltage 16 100 125 Figure 11A. ITRIP to Output Shutdown Time vs.
PAGE 17
IR2136(2)(3)(5)(6)(7)(8)(J&S) & (PbF) 3.0 1200 FAULT Clear Time (ms) Fault Indication Time (ns) 1000 M ax. 800 Typ. 600 M in. 400 200 2.5 M ax. 2.0 Typ. 1.5 M in. 1.0 0.5 0 10 12 14 16 18 -50 20 -25 0 Figure 12B. ITRIP to FAULT Indication Time vs. Supply Voltage 75 100 125 600 500 Dead Time (ns) 2.5 Fault Clear Time (ms) 50 Fig13A. FAULT Clear Time vs. Temperature 3.0 2.0 25 Temperature (oC) Supply Voltage (V) M ax. Typ. 1.5 M in. 1.0 400 M ax. 300 Typ. M in.
PAGE 18
IR2136(2)(3)(5)(6)(7)(8)(J&S) & (PbF) 600 6 Logic "0" Input Threshold (V) 500 Dead Time (ns) M ax. 400 Typ. 300 M in. 200 100 5 4 M ax. 3 2 1 0 0 10 12 14 16 18 20 -50 -25 0 Supply Voltage (V) 100 125 Figure 15A. Logic "0" Input Threshold vs. Temperature 6 5 5 Logic "1" Input Threshold (V) Logic "0" Input Threshold (V) 75 Temperature ( C) 6 4 M ax. 2 1 0 4 3 2 M in. 1 0 10 12 14 16 18 Supply Voltage (V) Figure 15B. Logic "0" Input Threshold vs.
PAGE 19
IR2136(2)(3)(5)(6)(7)(8)(J&S) & (PbF) ITRIP Positive Going Threshold (mV Logic "1" Input Threshold (V) 6 5 4 3 2 M in. 1 0 10 12 14 16 18 20 800 700 600 M ax. 500 Typ. 400 M in. 300 200 -50 -25 0 Supply Voltage (V) ITRIP Positive Going Threshold (V ITRIP Positive Going Threshold (mV Typ. 400 M in. 300 200 10 12 14 16 18 Supply Voltage (V) Figure 17B. ITRIP Positive Going Threshold vs. Supply Voltage (IR2136/21362/21363/IR21366 Only) www.irf.com 100 125 Figure 17A.
PAGE 20
IR2136(2)(3)(5)(6)(7)(8)(J&S) & (PbF) 3.0 High Level Output Voltage (V) ITRIP Positive Going Threshold (V 5.5 5.0 M ax. 4.5 Typ. 4.0 M in. 3.5 3.0 2.5 2.0 1.5 M ax. 1.0 Typ. 0.5 0.0 12 14 16 18 20 -50 -25 0 75 100 125 Temperature ( C) Figure 18A. High Level Output vs. Temperature Figure 17D. ITRIP Positive Going Threshold vs. Supply Voltage (IR21365/IR21367/IR21368 Only) 3.0 1.2 Low Level Output Voltage (V) High Level Output Voltage (V) 50 o Supply Voltage (V) 2.5 2.0 M ax.
PAGE 21
Low Level Output Voltage (V) 1.2 1.0 0.8 M ax. 0.6 0.4 Typ. 0.2 0.0 10 12 14 16 18 20 Supply Voltage (V) V CC or V BS Undervoltage Lockout (+) (V IR2136(2)(3)(5)(6)(7)(8)(J&S) & (PbF) 12 11 10 M ax. 9 Typ. 8 M in. 7 -50 9 M ax. Typ. 8 M in. 7 6 -50 -25 0 25 50 75 100 Temperature (oC) Figure 21. VCC or VBS Undervoltage (-) vs. Temperature (IR2136/IR21368 Only) www.irf.com 125 25 50 75 100 125 Figure 20. VCC or VBS Undervoltage (+) vs.
PAGE 22
12 11 M ax. 10 Typ. 9 M in. 8 7 -50 -25 0 25 50 75 100 125 Temperature (oC) Offset Supply Leakage Current ( µA) V CC or V BS Undervoltage Lockout (-) (V) 13 12 M ax. Typ. M in. 10 9 -50 -25 0 25 50 75 100 125 Temperature ( oC) Figure 25. V CC or V BS Undervoltage (-) vs. Temperature (IR21363/21365/IR21366/IR21367 Only) 22 13 12 M ax. Typ. 11 M in. 10 -50 -25 0 25 50 75 100 125 o Temperature ( C) Figure 24. V CC or V BS Undervoltage (+) vs.
PAGE 23
500 250 400 200 VBS Supply Current (µA) Offset Supply Leakage Current ( A) IR2136(2)(3)(5)(6)(7)(8)(J&S) & (PbF) 300 200 100 150 M ax. 100 50 Typ. M ax. 0 0 100 200 300 400 500 -50 600 -25 0 75 100 125 Figure 27A. VBS Supply Current vs. Temperature 250 5 200 4 VCC Supply Current (mA) VBS Supply Current ( A) 50 o Figure 26B. Offset Supply Leakage Current vs. VB Boost Voltage 150 100 25 Temperature ( C) V B Boost Voltage (V) M ax. 50 3 2 1 M ax. Typ. Typ.
PAGE 24
IR2136(2)(3)(5)(6)(7)(8)(J&S) & (PbF) 800 Logic "1" Input Current ( µA) VCC Supply Current (mA) 5 4 3 2 1 M ax. Typ. 600 400 200 M ax. Typ. 0 0 10 12 14 16 18 -50 20 -25 0 50 75 100 125 Temperature ( C) Figure 28B. VCC Supply Current vs. Figure 29A. Logic "1" Input Current vs. Temperature (IR2136/21363/21365 and IR21362 Low Side Only) VCC Supply Voltage 300 Logic "1" Input Current ( µA) 800 Logic "1" Input Current ( A) 25 o Supply Voltage (V) 600 400 M ax.
PAGE 25
300 600 250 500 Logic "0" Input Current ( µA) Logic "1" Input Current ( A) IR2136(2)(3)(5)(6)(7)(8)(J&S) & (PbF) 200 150 M ax. 100 50 Typ. 400 300 200 M ax. 100 Typ. 0 0 10 12 14 16 18 -50 20 -25 0 50 75 100 125 Temperature ( C) Figure 29D. Logic "1" Input Current vs. Supply Voltage (IR21362 High Side Only) Figure 30A. Logic "0" Input Current vs.
PAGE 26
IR2136(2)(3)(5)(6)(7)(8)(J&S) & (PbF) 250 "High" ITRIP Current ( µA) Logic "0" Input Current ( A) 4 3 2 M ax. 1 200 150 100 50 Typ. Typ. 0 0 10 M ax. 12 14 16 18 -50 20 -25 0 50 75 100 125 o Temperature ( C) Supply Voltage (V) Figure 31A. "High" ITRIP Current vs. Temperature Figure 30D. Logic "0" Input Current vs. Supply Voltage (IR21362 High Side Only) 4 250 200 "Low" ITRIP Current (µA) "High" ITRIP Current ( A) 25 150 M ax. 100 50 Typ. 3 2 M ax. 1 Typ.
PAGE 27
IR2136(2)(3)(5)(6)(7)(8)(J&S) & (PbF) 200 "High" IEN Current (µA) "Low" ITRIP Current ( A) 4 3 2 M ax. 1 150 100 M ax. 50 Typ. Typ. 0 0 10 12 14 16 18 -50 20 -25 0 Supply Voltage (V) 50 75 100 125 o Figure 32B. "Low" ITRIP Current vs. Supply Voltage Figure 33A. "High" IEN Current vs. Temperature 4 250 200 "Low" IEN Current (µA) "High" IEN Current ( A) 25 Temperature ( C) 150 M ax. 100 50 3 2 M ax. 1 Typ. Typ.
PAGE 28
IR2136(2)(3)(5)(6)(7)(8)(J&S) & (PbF) 4 RCIN Input Bias Current ( A) "Low" IEN Current ( A) 4 3 2 1 M ax. 0 Typ. 10 12 14 16 18 3 2 M ax. 1 Typ. 0 20 -50 -25 0 25 Supply Voltage (V) 50 75 100 125 Temperature (oC) Figure 35A. RCIN Input Bias Current vs. Temperature Figure 34B. "Low" IEN Current vs. Supply Voltage Figure 34B. “Low” IEN Current vs. Supply Voltage 400 Output Source Current (mA) RCIN Input Bias Current ( A) 4 3 2 M ax. 1 300 Typ. 200 M in. 100 Typ.
PAGE 29
500 500 400 400 Output Sink Current (mA) Output Source Current (mA) IR2136(2)(3)(5)(6)(7)(8)(J&S) & (PbF) 300 200 Typ. 100 Typ. 300 M in. 200 100 M in. 0 0 10 12 14 16 18 20 -50 -25 0 Supply Voltage (V) 50 75 100 125 o Temperature ( C) Figure 36B. Output Source Current vs. Supply Voltage Figure 37A. Output Sink Current vs. Temperature 250 RCIN Low On-resistance ( Ω ) 600 500 Output Sink Current (mA) 25 400 300 Typ. 200 M in. 100 200 150 100 M ax. 50 Typ.
PAGE 30
IR2136(2)(3)(5)(6)(7)(8)(J&S) & (PbF) 250 FAULT Low On-resistance ( Ω ) RCIN Low On-resistance ( ) 250 200 150 M ax. 100 Typ. 50 200 150 100 M ax. 50 Typ. 0 0 10 12 14 16 18 20 -50 -25 Supply Voltage (V) 50 75 100 125 Temperature ( C) Figure 39A. FAULT Low On-resistance vs. Temperature 0 VS Offset Supply Voltage (V) 250 FAULT Low On-resistance ( ) 25 o Figure 38B. RCIN Low On-resistance vs. Supply Voltage 200 150 M ax. 100 Typ. 50 0 -3 Typ.
PAGE 31
120 120 100 100 80 60 40 300V 200V 100V 0V Junction Temperature (oC) Junction Temperature o(C) IR2136(2)(3)(5)(6)(7)(8)(J&S) & (PbF) 20 60 300V 200V 100 V 0V 40 20 0.1 1 10 Frequency (KHz) 100 0.1 Figure 41. IR2136/IR21362(3)(5)(6)(7)(8) Ω, Vcc=15V vs. Frequency (IRG4BC20W), Rgate=33Ω 120 120 100 100 80 60 300V 200V 100 0V V 40 1 10 Frequency (KHz) 100 Figure 42. IR2136/IR21362(3)(5)(6)(7)(8) Ω, Vcc=15V vs.
PAGE 32
120 120 100 100 80 60 300V 200V 100V 0V 40 Junction Temperature (oC) Junction Temperature (oC) IR2136(2)(3)(5)(6)(7)(8)(J&S) & (PbF) 20 0.1 1 10 Frequency (KHz) 300V 200V 100V 0V 40 0.1 120 120 100 100 80 60 300V 200V 100V 0V 40 10 Frequency (KHz) 100 80 60 300V 200V 100V 40 0V 20 20 0.1 1 10 Frequency (KHz) 100 Figure 47. IR2136/IR21362(3)(5)(6)(7)(8) (J) Ω, Vcc=15V vs. Frequency (IRG4BC40W), Rgate=10Ω 32 1 Figure 46. IR2136/IR21362(3)(5)(6)(7)(8) (J) Ω, Vcc=15V vs.
PAGE 33
120 120 100 100 80 60 300V 200V 100 V0V 40 Junction Temperature (oC) Junction Temperature (oC) IR2136(2)(3)(5)(6)(7)(8)(J&S) & (PbF) 80 60 300V 40 200V 100 0V V 20 20 0.1 1 10 Frequency (KHz) 0.1 100 Figure 49. IR2136/IR21362(3)(5)(6)(7)(8) (S) Ω, Vcc=15V vs. Frequency (IRG4BC20W), Rgate=33Ω 1 10 Frequency (KHz) 100 Figure 50. IR2136/IR21362(3)(5)(6)(7)(8) (S) Ω, Vcc=15V vs.
PAGE 34
IR2136(2)(3)(5)(6)(7)(8)(J&S) & (PbF) Case outlines 28-Lead PDIP (wide body) 28-Lead SOIC (wide body) 34 01-6011 01-3024 02 (MS-011AB) 01-6013 01-3040 02 (MS-013AE) www.irf.
PAGE 35
IR2136(2)(3)(5)(6)(7)(8)(J&S) & (PbF) NOTES 44-Lead PLCC w/o 12 leads www.irf.com 01-6009 00 01-3004 02(mod.
PAGE 36
IR2136(2)(3)(5)(6)(7)(8)(J&S) & (PbF) LEADFREE PART MARKING INFORMATION Part number Date code IRxxxxxx YWW? Pin 1 Identifier ? P IR logo ?XXXX Lot Code (Prod mode - 4 digit SPN code) MARKING CODE Lead Free Released Non-Lead Free Released Assembly site code Per SCOP 200-002 ORDER INFORMATION Basic Part 28-Lead PDIP IR2136/IR21363(5)(6)(7)(8) 28-Lead SOIC IR2136/IR21363(5)(6)(7)(8) (S) 44-Lead PLCC IR2136/IR21363(5)(6)(7)(8) (J)) 28-Lead PDIP IR21362 28-Lead SOIC IR21362S 44-Lead PLCC IR21362J order