User manual

ManualsBrandsINFINEON TECHNOLOGIES ManualsDev KitsPCB design board

Microcontroller

Evaluation Board

For XMC1000 Family

Board User‘s Manual

Revision 1.0, 2014-02-20

XMC 2Go Kit with XMC1100

Kit Version 1.0

Summary of content (15 pages)

PAGE 1
E valu atio n B oar d For XMC1000 Family XMC 2 Go Kit wit h X M C11 00 Kit Version 1.0 Boa rd Us er‘s Ma nu al Revision 1.
PAGE 2
Edition 2014-02-20 Published by Infineon Technologies AG 81726 Munich, Germany © 2014 Infineon Technologies AG All Rights Reserved. Legal Disclaimer The information given in this document shall in no event be regarded as a guarantee of conditions or characteristics.
PAGE 3
XMC 2Go XMC 2Go Kit with XMC1100 Revision History Page or Item Subjects (major changes since previous revision) Revision 1.
PAGE 4
XMC 2Go XMC 2Go Kit with XMC1100 Table of Contents Table of Contents Introduction ............................................................................................................................................................ 7 1 1.1 1.2 Overview ............................................................................................................................................. 7 Key Features .............................................................................................
PAGE 5
XMC 2Go XMC 2Go Kit with XMC1100 List of Figures List of Figures Figure 1 Figure 2 Figure 3 Figure 4 Figure 5 Figure 6 Block Diagram of the XMC 2Go Kit ...................................................................................................... 8 XMC 2Go Kit with XMC1100 ................................................................................................................ 9 Pinning of Pin Header ...........................................................................................
PAGE 6
XMC 2Go XMC 2Go Kit with XMC1100 List of Tables List of Tables Table 1 Table 2 Table 3 Table 4 Features of the XMC 2Go Kit with XMC1100 ...................................................................................... 7 Pins used for the User LEDs .............................................................................................................. 10 XMC1100 Pins used for Debugging and UART Communication ....................................................... 11 List of Material ............
PAGE 7
XMC 2Go XMC 2Go Kit with XMC1100 Overview Introduction This document describes the features and hardware details of the XMC 2Go equipped with the ARM® Cortex™M0 based XMC1100 Microcontroller from Infineon Technologies AG. 1 Overview The XMC 2Go is designed to evaluate the capabilities of the XMC1100 Microcontroller and the powerful, free of charge tool chain DAVE™. This board is not cost optimized and does not serve as a reference design. 1.
PAGE 8
XMC 2Go XMC 2Go Kit with XMC1100 Overview 1.2 Block Diagram The block diagram in Figure 1 shows the main components of the XMC 2Go Kit including the power supply concept.
PAGE 9
XMC 2Go XMC 2Go Kit with XMC1100 Hardware Description 2 Hardware Description The following sections give a detailed description of the board hardware and how it can be used. Figure 2 shows the components of the XMC 2Go Kit with XMC1100. XMC4200 Debug IC and UART to USB Bridge Pin Header X1 User LED2 @ P1.1 Voltage Regulator & Reverse Current Protection Diode Pin Header distance fits to Breadboard Crystal for Debug IC User LED1 @ P1.
PAGE 10
XMC 2Go XMC 2Go Kit with XMC1100 Hardware Description 2.2 Pin Header Connector P2 P2 P2 P2 X2 X1 .7 P2 P0 .9 P2 P0 .1 0 G N P0 .1 1 3. 3V P0 .0 P0 P0 .5 P0 P0 D The pin headers X1 and X2 can be used to extend the evaluation board or to perform measurements on the XMC1100. The order of pins available at X1 and X2 corresponds to the pinning schema of the XMC1100 Microcontroller in the TSSOP-16 pin package. The pinning table is also printed onto the bottom side of the PCB. .6 .0 5 .
PAGE 11
XMC 2Go XMC 2Go Kit with XMC1100 Production Data 2.4 Debugging and UART Communication The on-board debugger supports 2-pin Serial Wire Debug (SWD), Single Pin Debug (SPD) and UART communication. Both require the installation of Segger’s J-Link Driver which is part of the DAVE™ installation. DAVE™ is a high-productivity development platform for the XMC microcontroller families to simplify and shorten SW development. It can be downloaded at www.infineon.com/dave.
PAGE 12
E D C B Target Device (XMC1100) +5V GND 1 4 1 EN IN IC201 Power Supply GND C1 GND OUT 3 IFX54211 MBV33 C2 100nF/0402 100nF/0402 +3V3 1 2 3 4 5 6 7 8 X1 PINHD 8x1 0,1" TH P2.7/P2.8 P2.9 P2.10 P2.11 GND +3V3 P0.0 P0.5 P2.6 P2.0 P0.15 P0.14 P0.9 P0.8 P0.7 P0.6 +3V3 2 GND LEDs P1.0/LED1 P1.1/LED2 P2.7/P2.8 P2.9 P2.10 P2.11 RX_XMC4200 TX_XMC4200P2.6 P1.0/LED1 P1.1/LED2 P1.2/SWCLK P1.3/SWDP2.0 P0.0 P0.5 P0.6 P0.7 P0.8 P0.9 P0.12 P0.13 P0.14 P0.
PAGE 13
XMC 2Go XMC 2Go Kit with XMC1100 Production Data 3.2 Components Placement and Geometry X101 IC201 D101 C202 C201 C104 D102 R107 C106 R109 C103 R106 R105 C101 R101 IC101 38.5 mm C107 LED101 R102 C102 C109R108 Q101 C105 C108 C110 R104 R103 C2 C1 IC1 P2 P1 LED2 R2 LED1 R1 14.0 mm Figure 6 Components Placement and Geometry Board Users Manual 13 Revision 1.
PAGE 14
XMC 2Go XMC 2Go Kit with XMC1100 Production Data 3.3 List of Material The list of material is valid for the XMC 2Go Kit with XMC1100 Version 1. Table 4 No. List of Material Qty Value 14 9 2 2 1 1 3 1 1 2 1 3 2 1 1 15 1 16 1 17 1 1 1 2 1 2 3 4 5 6 7 8 9 10 11 12 13 18 19 20 100nF 50V 0402 10% X5R CER 15pF 50V 0402 10% COG CER 10uF 10V 0603 10% X5R CER 4.7uF 10V 0603 10% X7R CER NX3225SA 12MHZ AT-W 3.2X2.
PAGE 15
w w w . i n f i n e o n .