ENGLISH TOTAL SPEAKER SOLUTIONS TSS-800 Owner’s Guide (230V)
Declaration of Conformity Declaration of Conformity We, Harman Consumer Group International 2, route de Tours 72500 Chateau du Loir France We, Harman Consumer Group International 2, route de Tours 72500 Chateau du Loir France declare in own responsibility that the products described declare in own responsibility that the product described in this owner’s manual are in compliance with technical in this owner’s manual is in compliance with technical standards: standards: EN 61000-6-3:2001 EN 55013:
ENGLISH TSS-800 OWNER’S GUIDE Table of Contents ii Important Safety Precautions 1 Introduction 1 Unpacking the System 1 Planning Your System 2 Placement 2 Wall-Mounting the Satellites and Center Channel 4 Center and Satellite Speaker Connections 5 Subwoofer Controls 6 Subwoofer Connections 7 Operation 7 Maintenance and Service 8 Specifications TSS-800 (230V) iii
INTRODUCTION PLANNING YOUR SYSTEM Infinity Total Solutions™ Before deciding where to best place your speakers, survey your room and study Figures 1 and 2. Infinity Total Solutions continues Infinity’s longstanding commitment to accurate sound reproduction. Our proprietary Metal Matrix Diaphragm™ (MMD®) drivers, precision dividing networks and rigid, well-braced enclosures combine to deliver uncompromised performance in any stereo or multichannel home theater system.
ENGLISH PLACEMENT Left and Right Front Channels Using the Satellite on the Shelf Stand For left and right front channels, place one satellite to the left and another to the right of the television, as shown in Figure 1. Since the speakers are magnetically shielded, you can place them very close to the TV without worrying about the magnetic field distorting the picture.
Adjustable Wall Bracket Step 1. Mark the positions on the wall where you would like to place the mounting screws. Step 4. Screw the ball and shaft assembly (B) to the lower 1/4"-20 insert on the rear of the satellite, or the upper insert on the rear of the center channel. Back out 1/2 of a turn and tighten the nut against the speaker. Step 2. Place bracket against the wall and fasten four 1-1/2" #10 wood screws through the bracket’s screw holes into the wall.
ENGLISH CENTER AND SATELLITE SPEAKER CONNECTIONS Turn Off All Power Center Channel After placing the speakers, you are ready to connect your system. First, turn off all audio-system power. Use high-quality speaker wire to make your connections. #18-gauge speaker wire with polarity coding is included. For longer distances, #16-gauge or heavier wire is recommended.The side of the wire with a ridge or other coding is usually considered positive polarity (i.e., +).
SUBWOOFER CONTROLS Rear Panel 0 Subwoofer-Level Control 1 Crossover-Frequency Adjustment ¡ ™ £ 2 Phase Switch 3 LFE Input 4 Line-Level Inputs 5 Power Indicator LED ¢ 6 Power Switch ∞ § TSS-SUB800/230 ¶ A Few Suggestions We recommend that you do not operate your speakers or subwoofer with the bass, treble and loudness controls set to full boost.This will place undue strain on your electronics and speakers and could damage them.
ENGLISH SUBWOOFER CONNECTIONS If you have a Dolby® Digital or DTS® receiver/ processor with a low-frequency-effects (LFE) or subwoofer output: If your receiver/processor does not contain a Dolby Digital or DTS processor but has a subwoofer output: RECEIVER/PROCESSOR SUBWOOFER OR LFE OUTPUT 15' (4.6m) subwoofer cable included 15' (4.6m) subwoofer cable included NOTE: If your receiver/processor has only one sub out, you may use either the L or R input.
OPERATION Surround Modes Crossover Adjustment When using the TSS-800 in a Dolby Digital or DTS home theater system, make sure all speakers are set to “Small”. In a Dolby Pro Logic® home theater system, make sure the receiver’s center channel mode is set to “Normal.” The Crossover Frequency Control 1 determines the highest frequency at which the subwoofer reproduces sounds. For the TSS800, it is recommended that this control be set at 120Hz (approximately the 3 o’clock position).
ENGLISH SPECIFICATIONS TSS-800 Satellites Center Channel Frequency Range: 120Hz – 30kHz (±3dB) 120Hz – 30kHz (±3dB) Recommended Amplifier Power Range: 10 – 100 Watts 10 – 125 Watts Sensitivity: 88dB 89dB Nominal Impedance: 8 Ohm 8 Ohm Crossover Frequency: 3.5kHz; 12dB/Octave 3.
© 2006 Harman International Industries, Incorporated. All rights reserved. Infinity Systems, 250 Crossways Park Drive, Woodbury, NY 11797 USA www.infinitysystems.com Infinity, Harman International and MMD are trademarks of Harman International Industries, Incorporated, registered in the United States and/or other countries. Total Solutions and Metal Matrix Diaphragm are trademarks of Harman International Industries, Incorporated. Dolby and Pro Logic are registered trademarks of Dolby Laboratories.