User Manual

ManualsBrandsInfinity Drain ManualsAccessories for waterFFAS 65 Install Instructions

Fixed Flange Series

Side Outlet Series

Installation Instructions

The Fixed Flange Series & Side Outlet Series are intended for use with the following

waterproong methods:

Liquid Waterproofing

Fabric Waterproofing

Dimension are subject to Manufacturers tolerance and change without notice. We can assume no responsibility for

use of superseded or void data.

Las dimensiones están sujetos a la tolerancia del fabricante y cambio sin previo aviso. No podemos asumir ninguna

responsabilidad por el uso de datos a sustituir los nulos.

Infinity Drain • 18 Secatoag Avenue, Port Washington, New York 11050

Phone 516.767.6786 • Fax 516.740.3066 • www.InfinityDrain.com

Made in the U.S.A.

FFED 25

FTED 25

FFED 65

FTED 65

FFAS 125

FFMN 25

FTMN 25

FFMN 65

FTMN 65

FTC

CUSTOM

FFDG 25

FTDG 25

FFDG 65

FTDG 65

FFC CUSTOM

FFAS 25

FTAS 25

FFAS 65

FTAS 65

FFTIF 65

FTTIF 65

Summary of content (8 pages)

PAGE 1
Fixed Flange Series Side Outlet Series Installation Instructions FFED 25 FTED 25 FFDG 25 FTDG 25 FFMN 25 FTMN 25 FFAS 25 FTAS 25 FFED 65 FTED 65 FFDG 65 FTDG 65 FFMN 65 FTMN 65 FFAS 65 FTAS 65 FFAS 125 FFC CUSTOM FTC CUSTOM FFTIF 65 FTTIF 65 The Fixed Flange Series & Side Outlet Series are intended for use with the following waterproofing methods: Liquid Waterproofing ° ° Fabric Waterproofing Made in the U.S.A. Infinity Drain • 18 Secatoag Avenue, Port Washington, New York 11050 Phone 516.767.
PAGE 2
Fixed Flange (FF) Series Components: SS=Stainless Steel FFED 25 Series FFDG 25 Series FFMN 25 Series FFAS 25 Series EA 6532 32″ SS Grate DA 6532 32″ SS Grate MA 6532 32″ SS Grate SA 6532 32″ SS Grate EA 6536 36″ SS Grate DA 6536 36″ SS Grate MA 6536 36″ SS Grate SA 6536 36″ SS Grate EA 6542 42″ SS Grate DA 6542 42″ SS Grate MA 6542 42″ SS Grate SA 6542 42″ SS Grate EA 6548 48" SS Grate DA 6548 48" SS Grate MA 6548 48" SS Grate SA 6548 48" SS Grate EA 6560 60" SS Grate
PAGE 3
Side Outlet (FT) Series Components: SS=Stainless Steel FTED 25 Series FTDG 25 Series FTMN 25 Series EA 6532 32″ SS Grate DA 6532 32″ SS Grate MA 6532 32″ SS Grate EA 6536 36″ SS Grate DA 6536 36″ SS Grate MA 6536 36″ SS Grate EA 6542 42″ SS Grate DA 6542 42″ SS Grate MA 6542 42″ SS Grate EA 6548 48" SS Grate DA 6548 48" SS Grate MA 6548 48" SS Grate EA 6560 60" SS Grate DA 6560 60" SS Grate MA 6560 60" SS Grate OC 6532 32" SS Fixed Channel OC 6532 32" SS Fixed Channel
PAGE 4
Tenga en cuenta: Instalador debe comprobar todas las dimensiones en las partes previa a la instalación y consultar localmente y nacionalmente los códigos. La conformidad y el cumplimiento de códigos local y nacional es responsabilidad del instalador. Note: Installer must verify all roughin dimensions prior to installation and consult local and national codes. Conformity and compliance to local and national codes are the responsibility of the installer.
PAGE 5
FIXED FLANGE (FF) SERES KEY SIDE OUTLET (FT) SERIES KEY (A) Top Grate – EA/DA/MA/SA/LA Liquid/Fabric Waterproofing (A) Top Grate – (B) Adjustable Feet EA/DA/MA/SA/LA Liquid/Fabric Waterproofing (B) Adjustable Feet (C) Bottom Channel – OC 65 (C) Bottom Channel – FC 65 (D) Side Outlet (D) Vertical Outlet (E) Rubber Coupling* (E) Rubber Coupling* (F) Waste Pipe (F) Waste Pipe Installation Instalación 1. Locate the waste line position.
PAGE 6
Note: When floor pitch is needed to begin at a zero level, determine the length of the channel (B) less the 1” flange around it’s perimeter. Cut a hole in the subfloor to the measured dimensions at the desired location. Place the ST65/ST125 Placement Brackets (Optional Component) in the newly created hole and screw into subfloor. Recess the stainless steel channel (C) into the subfloor and bracket. Allow the 1” flange to sit onto the subfloor.
PAGE 7
Waterproofing Membrane Waterproofing Membrane Mortar Bed Mortar Bed Sub-floor Sub-floor Before finishing material • Antes que el material esté terminado Assure that grate is lower than installed tile Tile Assure that grate is lower than installed tile Tile After finishing material • Después que el material esté terminado 6. Place finished top grate (A) into the installed bottom channel (C). Use adjustable feet (B) to raise or lower the top grate to be 1/16” below the finishing material height.
PAGE 8
FIXED FLANGE (FF) SERES Backer Board Thinset Finished Grate Finishing Material Liquid/Fabric Waterproofing Mortar Bed Subfloor Rubber Coupling Waste Line Stainless Steel Channel SIDE OUTLET (FT) SERIES Backer Board Thinset Finished Grate Finishing Material Liquid/Fabric Waterproofing Mortar Bed Subfloor Rubber Coupling Stainless Steel Channel 8