Powered Subwoofer INFINITY BETA SW-12 ™ Owner’s Guide (230V)
CAUTION Declaration of Conformity RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: To prevent electric shock, do not remove the grounding plug on the power cord, or use any plug or extension cord that does not have a grounding plug provided. Make certain that the AC outlet is properly grounded. Do not use an adapter plug with this product.
BETA SW-12 OWNER’S GUIDE Table of Contents ii Important Safety Precautions 1 Placement 2 Controls and Connections 3 Connections 4 Operation 5 Bass Optimization System™ 6 Maintenance and Service 6 Specifications Here are several additional facts on installation that may prove useful. It is generally believed by most audio authorities that low frequencies (below 125Hz) are nondirectional and, therefore, placement of a subwoofer within any listening room is not critical.
CONTROLS AND CONNECTIONS Rear Panel 2 1 3 BASS OPTIMIZATION SYSTEM FREQUENCY 4 PHASE Normal 0 LFE 5 7 50 150 CROSSOVER WIDTH LEVEL 180 0 ON OFF POWER 6 8 MIN MAX LEVEL 9 GREEN: ON RED: STANDBY LINE LEVEL IN R L R HIGH LEVEL IN A POWER ON L C OFF R HIGH LEVEL OUT B L _ Infinity Systems Northridge, CA USA + Bass Optimization Controls (see page 5) 4 Phase Switch 0 Bass Optimization System Selector 5 Normal/LFE Switch 1 Center-Frequency Adjustment 6 Power Indicator 2 Bass
CONNECTIONS If your receiver/amplifier does not have subwoofer outputs for the left and right channels or an LFE output: If your receiver/processor has subwoofer outputs for the left and right channels: RECEIVER/PROCESSOR RECEIVER/AMPLIFIER Front Speaker Output BASS OPTIMIZATION SYSTEM FREQUENCY LEVEL 180 Normal 0 LFE WIDTH ON PHASE GREEN: ON RED: STANDBY OFF POWER BASS OPTIMIZATION SYSTEM 50 150 CROSSOVER MIN MAX LEVEL LINE LEVEL IN FREQUENCY WIDTH LEVEL 180 Normal 0 LFE R ON PHAS
OPERATION Power On Crossover Adjustments Plug your subwoofer’s AC cord into a wall outlet. Do not use the outlets on the back of the receiver. Note: This control will have no effect if the Normal/LFE Switch 5 is set to “LFE.” If you have a Dolby Digital or DTS processor/receiver, the Crossover Frequency is set by the processor/receiver. Consult your owner’s manual to learn how to view or change this setting. Initially set the Subwoofer Level (Volume) Control 8 to the “min” position.
BASS OPTIMIZATION SYSTEM™ Infinity’s Bass Optimization System is a simple-to-use, yet sophisticated, low-frequency calibration system.The Beta SW-12 contains a parametric equalizer that you can adjust following the directions below. By following these instructions, you can improve the sound of your system. The Bass Optimization System Goal It is a fact of audio that what we hear at low frequencies is determined as much or more by the listening room than by the loudspeaker itself.
MAINTENANCE AND SERVICE The enclosure and grille may be cleaned using a soft cloth to remove fingerprints or to wipe off dust. All wiring connections should be inspected and cleaned or remade periodically.The frequency of maintenance depends on the metals involved in the connections, atmospheric conditions, and other factors, but once per year is the minimum. If a problem occurs, make sure that all connections are properly made and clean.
Infinity Systems, 250 Crossways Park Drive, Woodbury, NY 11797 USA 516.674.4INF (4463) www.infinitysystems.com *Trademark of Dolby Laboratories. DTS is a registered trademark of Digital Theater Systems, Inc. Infinity is a registered trademark, and Infinity Beta, CMMD and Bass Optimization System (B.O.S.) are trademarks, of Harman International Industries, Incorporated. Ceramic Metal Matrix Diaphragm patent nos. 6,327,372 and 6,404,897. Part No.