™ INTERLUDE POWERED SUBWOOFERS Owner’s Guide • IL100s • IL120s
CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: SHOCK HAZARD, DO NOT OPEN. AVIS: RISQUE DE CHOC ELECTRIQUE – NE PAS OUVRIR. CUIDADO: PELIGRO DE CHOQUE ELÉCTRICO – NO ABRIR. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (0R BACK) NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED PERSONNEL THIS INFINITY PRODUCT IS DESIGNED FOR 120-VOLT USE ONLY! FOR DETAILED SAFETY PRECAUTIONS, PLEASE SEE FOLLOWING PAGE IN THIS OWNER’S MANUAL FOR “IMPORTANT SAFETY INSTRUCTIONS.
IMPORTANT SAFETY PRECAUTIONS Read First! CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
INTERLUDE IL100S, IL120S OWNER’S GUIDE Table of Contents iv INTERLUDE IL100S, IL120S ii Caution iii Important Safety Precautions 1 Unpacking the Subwoofer 1 Placement of the Components 2 Controls and Connections 3 Connections 4 Operation 5 Bass Optimization System™ 6 Maintenance and Service 7 Specifications
Infinity Interlude Series The Interlude series of loudspeakers and powered subwoofers continues Infinity’s longstanding commitment to accurate sound reproduction. Our proprietary Ceramic Metal Matrix Diaphragm™ (C.M.M.D.™) drivers and Bass Optimization System,™ along with precision dividing networks and rigid, well-braced enclosures, combine to deliver uncompromised performance in any stereo or multichannel home theater.
CONTROLS AND CONNECTIONS Rear Panel Line Level In Out Input Select L L R R 1 2 + – Low-Pass Freq. Adjust 80Hz Speaker 50Hz Line 3 150Hz 4 Phase Bass Optimization System On 180o On 2 Line-Level Outputs Off 3 Input Selector Off 5 0o 9 6 4 Low-Pass Frequency Adjustment + – 1 Line-Level Inputs Low-Pass Filter Right 5 Low-Pass Filter Selector Left + In – – Out + Freq.
If your receiver/processor has subwoofer outputs for the left and right channels: CONNECTIONS RECEIVER/PROCESSOR If your receiver/processor does not have subwoofer outputs for the left and right channels or an LFE output: RECEIVER/AMPLIFIER Front Speaker Output Line Level In Out Input Select L L R R Low-Pass Freq. Adjust 80Hz Speaker 50Hz Line + – – – – 150Hz Low-Pass Filter Phase On 180 Off 0o Bass Optimization System o On Off • Set Input Selector to “Line.
OPERATION Power On Plug your subwoofer’s AC cord into a wall outlet. Do not use the outlets on the back of the receiver. Initially set the subwoofer’s Level Control M to the “O” position. Turn on your sub by pressing the power button 8 on the rear panel. Turn on your entire audio system and start a CD or movie soundtrack at a moderate level. Adjust Gain Turn your subwoofer’s Level Control M up to the “5” position (half way). If no sound emanates from the subwoofer, check the AC-line cord and input cables.
BASS OPTIMIZATION SYSTEM™ Infinity’s Bass Optimization System is a simple-to-use, yet sophisticated, low-frequency calibration system. Each Interlude subwoofer contains a parametric equalizer that you can adjust following the directions below. By following these instructions, you can improve the sound of your system. The Bass Optimization System Goal It is a fact of audio that what we hear at low frequencies is determined as much or more by the listening room than by the loudspeaker itself.
MAINTENANCE AND SERVICE plays the tones from the test CD and records the relative output level of each test tone, using the sound-level meter, on the provided measurement template. After all the tones are complete, the template contains a response curve for the frequencies below 100Hz.The user simply notes the frequency of the largest bass peak, calculates the correct amount of attenuation, and uses the “Q-Finder”to determine the width of the curve.
SPECIFICATIONS IL100s IL120s Frequency Response: 32Hz – 150Hz (±3dB) 28Hz – 150Hz (±3dB) Maximum Amplifier Output: 250 watts 500 watts Crossover Frequencies: 50Hz – 150Hz, 24dB/octave, continuously variable 50Hz – 150Hz, 24dB/octave, continuously variable Driver: 10" C.M.M.D. 12" C.M.M.D. Dimensions (H x W x D): 13-3/4" x 13-1/2" x 17" 17-1/2" x 17-1/4" x 19-3/4" Weight: 32 lb (14.5kg) 45 lb (20.5kg) (20Hz – 150Hz with no more than 0.
© 2000 Infinity Systems, Inc., 250 Crossways Park Drive, Woodbury, NY 11797 USA (800) 553-3332 (USA only) www.infinitysystems.com *Trademark of Dolby Laboratories. DTS is a registered trademark of Digital Theater Systems, Inc. Infinity is a registered trademark of Infinity Systems, Inc. Printed in USA 3/00 Part No.