(\::) lnTinify Infinity BeTA Be621 Component System HARMAN El■ Owner's Manual Mode d'emploi Manual del propietario reddot winner 2021 ---
Congratulations! BETA BE621 CRAFTED OF THE FINEST MATERIALS ON EARTH! INFINITY CUTTING EDGE MATERIALS FOR HIGHEST PERFORMANCE SOUND Thank you for choosing the Infinity BeTA Be621 component system. To get the best performance from your new speakers, it is strongly recommended that you have a qualified professional install them. . .Although this manual provides general instructions about installing the speakers, it does not include exact installation methods for any particular vehicle.
(\::) lnff niW HARMAN Infinity BeTA Be621 Component System WHAT'S IN THE BOX 8X 2X 2X Thread the tweeter wire through the center of the mounting cup. • Insert the tweeter into the cup, then twist clockwise to lock it in place. • Thread the pressure-fit nut onto the back of the flush-mount cup. Twist clockwise to hand-tighten. 2X • @ OJ j 2X • 2X 4X Surface-mounting the tweeters Surface-mounting is ideal for installing the tweeters on a sail panel, dash corner, or door panel.
Connecting the speakers to the crossover Installing the 6.5" woofers The woofers are usually mounted in your vehicle's factory woofer locations. which are typically in the doors (front) or side panels (rear). If you choose to mount them in a custom location, mounting them higher will raise the soundstage, while mounting them lower In the doors will provide excellent bass response.
NOTES: Non- bi-amping • Use appropriately sized speaker wire; 14- or 16-gauge is recommended. • Make sure your amplifier's RMS pcwer rating Is suitable for the tweeters and woofers (see specifications). • You will need to use a total of four channels of amplification from two 2-channel amplifiers or one 4-channel amplifier. IMPORTANT: Because of the lower impedance of the drivers, do not wire In parallel or bridge amplifier channels to prevent overheating the amplifier.
Dimensions Tweeter Surface-Mount Cup Dimensions Woofer Physical Dimensions Frame Outer Diameter (A) 6-15/16 in/ 176 mm Fixture Outer Diameter (A) 1-3/4 in/ 44.3 mm Fixture Mounting Hole Diameter (8) 1-3/4 In / 44.3 mm Gnlle Tray Outer Diameter (8) 6-15/16 In / 176 mm Rxture Mounting Depth (C) 1-7/16 in/ 36.7 mm Magnet Outer Diameter (C) 3-1/4 in/ 82.2 mm Tweeter Frontal Protrusion (D) 1-7/16in/36.7 mm Frontal Grille Protrusion (D) 29/32 in / 22.
Specifications BeTA Be621 1" Tweeter BeTA Be621 6.5" woofer Dome/Cone material Beryllium dome Coated Carbon Fiber Wave guide/ Grille Aluminum Die-casting SPCC Basket material Aluminum Die-casting Aluminum Die-casting Power Handling 50Wrms 100Wrms Frequency Response 1KHz -40kHz 60Hz-6kHz Sensitivity (2.83V/1m) 95dB 91dB Impedance 4 ohm 4ohm Fs 1.
~ ( ;j'fl,~ ffil ~ HARMAN J ----~ ~ ~· ffl~ (3i:~loliit) E3 M: 20 J=l 1f E3 £~"5W: ~~eg~: _ _ __ fflp9i,3: _ ±W(illBtOO: m~mff-: ffl~OO* §"im~, ~~'~ic~±n~:zt;:~iiE#~ ~~£~/¥iH!l=IBJB1iliff-JJPJ~~ffl*~ F□ij&~o t-J 71~a?fle'gtx'.tii, m12 ~~f'~B1~~-g-)!fi~B'g£~~#m;fffiiffiff:ij';:~fil~~§gg f,Ji, ±igtJt ~iMH~ ,l@,B'gED~o :zt;:~filP9g~ iffi ~~to/Jtff-iR:ff.J§.\:~ ~i&B'g~:fm1~~ /§ij&~' ffi~~,£t~U~ m1l~xgf'~tMH.li"5' ~"5mR~, ~i&§.\:;f~itiJ~ F*~5]~fx'.
CA_lnfinity_BeTA Be621 components_OM_EN+FR+ES+CN_SOP_V6
