Owner’s Guide NV29
Thank you for purchasing the Infinity Upright Vacuum. Contents Important Safety Instructions 2 Getting Started 4 Using the Vacuum 6 Transporting the Vacuum 7 Cleaning with the Vacuum Accessories 8 Emptying the Dust Cup Assembly 10 Proper Care of Your Infinity Upright Vacuum 11 Troubleshooting 12 Checking for Blockages 13 Maintenance 14 Warranty and Registration 16 TOLL FREE: 1-888-668-9600 www.infinityvac.
IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS For Household Use Only When using an electrical appliance, basic safety precautions should always be observed, including the following: READ ALL INSTRUCTIONS BEFORE USING YOUR INFINITY UPRIGHT VACUUM. WARNING: To reduce the risk of electric shock, the two-pronged power cord plug is polarized [one prong is larger than the other]; it will fit into the outlet only one way. DO NOT force into outlet or try to modify to fit.
Cyclonic Chamber/Dust Cup/Filters: Before turning on the vacuum: • Make sure that dust cup, cyclonic chamber and all filters are in place after routine maintenance. • Make sure that all components and filters are thoroughly dry after routine cleaning. • Only use filters and accessories provided by EURO-PRO Operating LLC [Failure to do so will void the warranty.] General Cleaning: DO NOT run the vacuum over large-sized objects.
Getting Started 1 a 5 b 2 c d 4 e f g 3 *h *i Along with your upright unit, you will find the following components: a Detachable Handle (Ergonomic Grip) b Telescopic Wand c Cleaning Attachments d Upper Hose Holder e Extra Filters f Super Stretch Hose g Spare Motor Belt *Note: depending on the model you select, your Infinity comes with a Pet Hair Power Brush (h) and Low Reach Bare Floor Brush (i) that are kept in a separate accessory bag.
6 Attach each end of the Super Stretch Hose to the vacuum and press into Upper Hose Holder for easy storage. IMPORTANT: To prevent vacuum from tipping, secure hose in lower holder. 7 7 Store Crevice Tool and Upholstery/ Dusting Brush on the unit. 8 8 When storing your vacuum, wind cord around the two cord holders and secure with cord clip: • Quick Cord release at the top of the unit – place in the upright position. • Second holder [fixed] near the base.
Using the Vacuum Your Infinity Upright Vacuum is a versatile tool that can be used to clean bare floor surfaces or carpets – with the click of a button. Lock vacuum into the upright position. Plug in the vacuum. Bare Floors (and Tools) Bare Floors 1 Carpets Carpets 5 1 4 2 3 1 2 1 Set the Height Adjustment Dial. When cleaning bare floors: 2 Set the Brush Roll Pedal for bare floors/tools or carpets.
Transporting the Vacuum Lock vacuum into the upright position. Unplug the vacuum. Wind cord around the two cord holders. Secure Super Stretch Hose in both hose holders. 2 1 4 4 Step on Power Button to turn unit on and off. Push to vacuum. Note: If vacuum is difficult to push, adjust the Height Adjustment Dial until vacuum glides easily over the carpet surface. 1 To roll the vacuum: Hold the Detachable Handle (Ergonomic Grip) and tilt unit back on wheels.
Cleaning with the Vacuum Accessories Before cleaning with your accessories: Lock vacuum into upright position. Secure Super Stretch Hose in the lower hose holder to prevent tipping. Change the Brush Roll Pedal to the bare floors/ tools position. DO NOT pull vacuum cleaner around by the hose. DO NOT overextend the hose beyond its 17-foot reach. a * Vacuum Accessories Your vacuum comes a Detachable Handle and Telescopic Wand. Use one or the other to attach your cleaning accessories.
c * b * Using the Telescopic Wand: Lock vacuum into upright position. Press the Telescopic Wand release button (b). Hold Telescopic Wand and pull out of unit. Push the selected cleaning tool onto the end of the wand. Press the Telescopic Height Adjustment Button (c) to adjust wand to desired length. *Note: depending on the model you select, your Infinity comes with a Pet Hair Power Brush and Low Reach Bare Floor Brush that are kept in a separate accessory bag.
Emptying the Dust Cup Assembly For best results empty the Dust Cup Assembly after each use; empty several times during prolonged usage. Or empty the Dust Cup Assembly when it reaches the MAX fill line; NEVER OVER-FILL THE DUST CUP. Lock vacuum into upright position. Turn vacuum off. CAUTION: Unplug the vacuum; failure to do so Might result in electric shock. 3 2 1 4 2 Insert Dust Cup Assembly deep inside trash receptacle to contain dust and debris.
Proper Care of Your Infinity Upright Vacuum Date Purchased: For proper care, consult the table to the right for the maintenance schedule of your Cyclonic Chamber and Filters. Lock vacuum into upright position. Turn vacuum off. CAUTION: Unplug the vacuum; failure to do so might result in electric shock. Remove Dust Cup Assembly.
Troubleshooting WARNING: to reduce the risk of electric shock, the power cord must be disconnected before performing maintenance/troubleshooting checks. Problem Vacuum will not run. Suggested Action Check to see if plugged in properly. Check circuit breaker/fuse. Check On/Off switch. If vacuum still does not run, see Resetting the Motor Thermostat on page 14. Vacuum is not picking up dirt. Check the Dust Cup. Check the Filters. Check Height Adjustment Dial setting; see Using the Vacuum on page 6.
Checking for Blockages Blockages may cause your vacuum to overheat and shut down. If so, clear the blockages, then follow the instructions for Resetting the Motor Thermostat on page 14. WARNING: Never insert sharp objects into any opening to clear an obstruction. IMPORTANT: Damages caused while clearing or attempting to clear blockages are not covered under your product’s limited warranty. 1 Detachable Handle: Lock vacuum into upright position.
Maintenance Changing the Headlight Bulb You will need to order replacement bulbs from: www.infinityvac.com or contact Customer Service at: 1-888-668-9600. Turn power off. Replacing the Power Nozzle Motor Belt If the brush roll does not engage when the carpet-to-floor pedal is in the carpets position, the belt may be worn or broken. Grasp both sides of the Brush Roll; with even tension, partially remove the right side from the side holder first then the left (c).
To replace new Belt: Slide one end of the new Belt over the motor-driven shaft (e). Push both ends all the way into the side holders at the same time. Cleaning the Pet Hair Power Brush Slide locking latch (k) forward. Gently tilt brush housing upward to open. Slide second end of the Belt around Brush Roll (f). IMPORTANT: DO NOT force; it will not open all the way. k fe f Center Belt on motor-driven shaft; test Brush Roll for easy turning.
Warranty and Registration Your Infinity Upright Vacuum comes with a Five year limited warranty. FOR CANADIAN CONSUMERS ONLY Please fill out and mail the Owner Registration Card within ten (10) days of purchase. The registration will enable us to contact you in the unlikely event of a product safety notification. By returning this card you acknowledge to have read and understood the instructions for use, and warnings set forth in the accompanying instructions.
Owner Registration Card FOR CANADIAN CONSUMERS ONLY Please fill out and mail this sheet within ten (10) days of purchase. The registration will enable us to contact you in the unlikely event of a product safety notification. By returning this card you acknowledge to have read and understood the instructions for use, and warnings set forth in the accompanying instructions. Mail to the following address: • Canada: EURO-PRO Operating LLC 4400 Bois Franc, St.
U.S.: EURO-PRO Operating LLC 94 Main Mill Street, Door 16, Plattsburgh, NY 12901 Canada: EURO-PRO Operating LLC 4400 Bois Franc St. Laurent, Québec H4S 1A7 1-888-668-9600 www.infinityvac.com COPYRIGHT© EURO-PRO OPERATING LLC 2007 PRINTED IN CHINA REV.