CHOOSING A LOCATION AND INTRODUCTION MOUNTING THE AMPLIFIER Power CONNECTIONS WARNING! Chooses a mounting location in the trunk or The Reference amplifiers are capable of WIRE-GAUGE CHART Playing loud music in an automobile can hinder cargo ares where the amplifier will not be dam delivering high power levels, and require a Amplifier Maximum Minimum your ability to hear traffic and permanently aged by shifting cargo.
Araucanian — 310a, 610a ano 1210a The Reference sub woofer amplifiers are single-channel amplifiers. There are two sets of terminals to make it easy ta connect multiple woofers. Either set of terminals may be used when connecting woofers, To the right are two application diagrams to help plan your sub woofer system installation, Figures 3 and 4 show how to configure the Reference sub woofer amplifiers {modest 30a, 10a and 1210a).
Application S — 7540a The 75402 can be set up for stereo &-channel, channel ar bridged 2-channel operation, as shown in Figures 7 through 9. NOTE: For simplicity, Figures 7 through 9 do not show power, remote and input connections. NOTE: Minimum speaker impedance for stereo operation is 2 ohms. Minimum speaker impedance for bridged operation is 4 ohms. NOTE: “Bass Boost” only affects rear channels, [r a rE ore FRONT noon stereo nar ie we Sle QUO OEY & Np wove eed Bass.
Capricorns — 5760a The 5760a can be configured for 6-channel, channel or 3-channel operation, as shown in Figures 10 through 12. INPUT MODE SWITCH: «Use INT {internal mode to send a signal from the front and rear inputs to the sub woofer.
INSTALLATION AND SETUP SETTING THE CROSSOVERS) Determine your system plans and set the crossover-mode switch accordingly. if your system design does not include a sub woofer, set the crossover mode to FLAT and skip to “Setting Input Sensitivity” MODE SWITCH Flat: Allows a full-range signal through to the speakers; can be used with larger full-range speakers such as 6" x 9's.
INSTALLATION AND SETUP (CONT.) SETTING DBO" (30a, 6100 and 12100] The Dynamic Bass Optimizer {DBO} is used to enhance low-frequency reproduction in a vehicle. Conventional bass-boost circuits only increase bass at a fixed frequency, and cause the amplifier to consume considerable power, The DBO allows you to adjust the frequency {20Hz 80Hz} as well as the boost level (up to 1208; see Figure 14}, allowing you ta its-tune the bass in your system to optimize performance.
SPECIFICATIONS Nos « 116W AMS x 1 channel at 4 ohms and s1%THD + N + Signal-to noise ratio; Sindbad (reference 1W into 4 ohms) «312 RMS x 1 channel at 2 ohms, 14.4V supply and S1%THD +N «Dynamic power: 347W at 2 ohms « Effective damping factor: 6.
We need to hear from you! o Warranty Service s Confirmation of Ownership the world of high fidelity, technology is ail woo often viewed as the 1 info we have a different 3 only the means to end pro swingeing: technology an end. The end result must be enjoyment of the programs and music you bear.
Amplifier Quick-Start Guide (1ila'vY full-range amplifier connections + Front _ Rear Sub woofers + + Front | _ Front | Rear : 2 Rear Sub woofer Ta HIGH LEVEL FP est Sub woofer Wer one FROWZY cos se.
Amplifier Quick-Start Guide sub woofer amplifier connections we coo DO rhea BOOST ooo O eho Boohoo oO LINE-LEVEL BATTERY — SUB LEVEL CONTROL {OPTIONAL} REMOTE TURN-ON Four 2-ohm woofers = 2-ohm load 080 —— NOTE: Minimum speaker load is 2 tums. So Infinity Infinity Systems 250 Cross ways Park Drive, Wood bury, NY 11787 USA 518.674.4INF (4483) FAX 516.662.3556 wwwlnfinitysystems.com ©2004 Haman International Industries, Incorporated Part No.
