INSTALLATION INSTRUCTIONS Instrucciones de instalación Installationsanleitung Instruções de Instalação Istruzioni di installazione Installatie-instructies Instructions d´installation Single Stud Short Throw Wall Mount Spanish Product Description German Product Description Portuguese Product Description Italian Product Description Dutch Product Description French Product Description SP-WALLKIT-01
SP-WALLKIT-01 Installation Instructions DISCLAIMER InFocus and its affiliated corporations and subsidiaries (collectively "InFocus"), intend to make this manual accurate and complete. However, InFocus makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product.
Installation Instructions SP-WALLKIT-01 LEGEND Tighten Fastener Pencil Mark Apretar elemento de fijación Marcar con lápiz Befestigungsteil festziehen Stiftmarkierung Apertar fixador Marcar com lápis Serrare il fissaggio Segno a matita Bevestiging vastdraaien Potloodmerkteken Serrez les fixations Marquage au crayon Loosen Fastener Drill Hole Aflojar elemento de fijación Perforar Befestigungsteil lösen Bohrloch Desapertar fixador Fazer furo Allentare il fissaggio Praticare un foro Be
SP-WALLKIT-01 Installation Instructions TOOLS REQUIRED FOR INSTALLATION 5/32" (included) (security) 1/2" (12.7mm) 3/8" (9.5mm) 7/32" (5.6mm) #2 1/2" (12.7mm) 7/16" (11.
Installation Instructions SP-WALLKIT-01 Site Requirements WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT! The figure below identifies the minimum requirements for installation of display mounts onto a steel stud structure. If the structure or its components do not meet these requirements contact the mount manufacturer for specific instructions before attempting installation.
SP-WALLKIT-01 Installation Instructions Assembly And Installation Mounting Wall Bracket Concrete or Concrete Block 1. Determine mounting location on wall. 2. Using mounting bracket (B) as a template, mark four holes at the outer holes in bracket. (See Figure 1) 3. Drill four 3/8" holes at marked locations in wall. (See Figure 1) 5 (J) x 4 (H) x 4 4 (K) x 4 (front view) (B) 2 X4 3 X4 (B) Figure 2 Wood Studs 1. Determine mounting location on wall. Use a stud finder to locate studs. 2.
Installation Instructions 6. SP-WALLKIT-01 Install three 5/16 x 2 1/2" hex head lag screws (J) through three 5/16" washers (K), inner holes of mounting bracket and into drilled holes. (See Figure 4) (front view) 4 X3 5 X3 steel stud 6 (J) x 3 (K) x 3 (B) Figure 5 Figure 4 6. Hold metal channel on anchor (M) flat alongside plastic straps and slide channel through hole.
SP-WALLKIT-01 Installation Instructions Steel Stud Steel Stud Drywall Drywall (N) x 3 Plastic Cap (L) x 3 12 8 (M) x 3 Anchor Metal Channel SIDE VIEW Wall bracket Figure 7 Anchor Metal Channel 9. Snap off plastic straps on anchor at wall by pushing side to side, snapping off straps level with flange of plastic cap. (See Figure 8) 10. Repeat steps 7 through 9 for each mounting hole. Figure 9 Installation to Wall Bracket Steel Stud Drywall 9 SIDE VIEW 1.
Installation Instructions 3. SP-WALLKIT-01 Install two 5/16-18 x 1/2" hex head cap screws (C) through two 5/16" washers (K) and into holes on mounting bracket and projector mount.
SP-WALLKIT-01 Installation Instructions WARNING: IMPROPER INSTALLATION CAN LEAD TO Projector Installation to Mount PROJECTOR FALLING RESULTING IN SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT. Make certain mounting slots in mount base slide under thumb screws and that screws are seated in the back of slots. WARNING: IMPROPER INSTALLATION CAN LEAD TO PROJECTOR FALLING RESULTING IN SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT. DO NOT substitute hardware.
Installation Instructions SP-WALLKIT-01 Pitch Adjustment Pitch Adjustment - Entire arm NOTE: Pitch can be adjusted using the projector mount or the 1. pitch of the entire arm can be adjusted. See "Pitch Adjustment - Entire Arm Section for details. 1. Remove two #8-32 x 3/4" Phillips pan machine screws (F) to free outer cover from mounting bracket. (See Figure 21) Loosen Pitch adjustment locking screw using a #2 Phillips screwdriver. (See Figure 19) 2.
SP-WALLKIT-01 Installation Instructions Cable Management (Optional) 4 6 1. Remove two #8-32 x 3/4" Phillips pan machine screws (F) to free outer cover from mounting bracket. (See Figure 25) or 5 (F) x 2 1 2 (C) x 2 3 7 Figure 25 Figure 23 2. 8. Slide outer cover of mount (A) back against mounting bracket. 9. Reinstall two #8-32 x 3/4" Phillips pan machine screws (F) through holes on sides of outer cover.
Installation Instructions SP-WALLKIT-01 (bottom view) 4 4 cable (example) projector Figure 27 4. Route projector cable(s) under mount cover and through short throw projector arm tunnel. (See Figure 27) 5. (Optional)Cables can be tied to inside of projector’s front cover using cable ties (not included). Route cables near front cover and wrap cable tie through slots on front cover and around cables. (See Figure 28) 6. Replace removed cable management covers (if necessary).
SP-WALLKIT-01 Installation Instructions Extension Adjustment 1. Loosen two bolts holding stop bracket in place on underside of short throw projector mount. (See Figure 30) 2. Adjust mount to desired extension length. (See Figure 30) 3. Tighten two bolts holding stop bracket to secure mount in desired position. (See Figure 30) (bottom view) 1 1 (F) x 2 3 2 (S) x 2 2 Figure 31 3. Remove two bolts holding stop bracket in place on underside of short throw projector mount.
Installation Instructions 4. SP-WALLKIT-01 Install two 1/4-20 x 1/2" button head security screws (Q) through holes in stop bracket and into holes in sliding nuts. (See Figure 33) adapter plate stop bracket sliding nuts x 4 (one at a time) 6 4 (Q) x 2 Figure 34 Figure 33 adapter plate 5. (Optional) Remove projector from short throw projector mount according to projector interface instructions.
SP-WALLKIT-01 Installation Instructions InFocus Corporation 13190 SW 68th Parkway, Ste 200 Portland, OR 97223 8802-002041 REV 00 2010 InFocus Corporation www.infocus.