Specifications

ManualsBrandsINGENICO ManualsPOS EquipmentSmart POS Terminal BASE

WWW.ingenico.com

28-32,boulevard de Grenelle, 75015 Paris - France/ (T)+33(0)1 58 01 80 00 / (F)+33 (0)1 58 01 91 35

Ingenico-SA au capital de 47 656 332 / 317 218 758 RCS Nanterre

Model:AXIUM DX8000-BASE-W2

User Guide

Summary of content (21 pages)

PAGE 1
User Guide Model:AXIUM DX8000-BASE-W2 WWW.ingenico.
PAGE 2
Contents 1. Product Introduction ......................................................................................................................................... 3 1.1 Open Package Inspection ............................................................................................................................ 3 1.2 Device Introduction ..................................................................................................................................... 3 1.
PAGE 3
1. Product Introduction 1.1 Open Package Inspection Open the package to check if there are any disabling masks or transportation damage in the terminals and fittings. Procedures： 1) Open the package 2) Check the following items(Subject to actual product configuration)  Base host  Product instruction  12V/3.33A power adapter  AC power cable 3) Save the transportation package and packing material for second use. 1.2 Device Introduction 1. RJ45 Network Interface2. USB-TYPE A3.USB-TYPE A 4.
PAGE 4
10.DX8000 Charging Contact 1.3Interface definition 1） RJ45 interface Sequence RJ45Signal 1 ETH_TX+ 2 ETH_TX- 3 ETH_RX+ 4 NC 5 NC 6 ETH_RX- 7 NC 8 NC 2） USB-TYPE A interface Sequence USB-TYPE A Signal 1 VBUS 5.
PAGE 5
2. Product Technology Features 2.1 Product Technology Specifications Port a DC12V JACK port a RJ45 network port two USB A HOST port supporting USB2.0 a USB B DEVICE port supporting USB2.0 Power Every USB HOSToutput: 5.0VDC0.5A Charge output: 5.0VDC 2.0A Power adapter: input 100-240V AC, 50/60Hz; output 12V DC3.33A Size and Weight Size：193.8mmx89mmx38.6mm Net Weight：0.20kg Gross Weight：0.70kg 2.
PAGE 6
3. WiFi connection 3.1 Connect DX8000 to the base WiFi     Power on the base. Check the SSID and password from the label on the back of base. Click “Settings” menu on DX8000,and then click “Network and Internet”, enter “ Wi-Fi” and select the base SSID to connect.(step 1~4) After that , DX8000 can use the RJ45 network of the base. Step1 Step2 Step3 Step4 3.2 Web Setting of base The base can be set from the web.  Use a computer to connect the base via WiFi.  The web setting IP of base is 192.
PAGE 7
 User can get and change the Ethernet parameter on the Network page.  User can get and change the WLAN parameter on the WLAN page.
PAGE 8
 User canchange the operating mode,enable DMZ or set static DHCP on the Advanced page.  User can update the firmware of base, save and reload the settings, change the password on the Manage page.
PAGE 9
3.3 Restore factory Setting   4.  Use sharp to click the RESET button to restore the factory setting of the base. The position of RESET button is below. Pairing connection If DX8000 want to use the USB ports on the base, it should be paired to the base. 4.1 Prepare for Base Pairing    Only one DX8000 can use the USB ports of the base at the same time. If the red indicator light is on, it indicates the base is available for pairing.
PAGE 10
 Illumination of two color indicator lights： SN 1 2 3 4 Light Condition Red light on Green light flashing Green light on Red light flashing Base Status Base to be paired Base paired but disconnected with DX8000 Base paired and connected with DX8000 Base in upgrading 4.2 Pair method     First,connect DX8000 to the base via chapter 3.1. Click “Settings” menu on DX8000,and then click “Base”,input the web password [Step1]. Click the grey button beside the SSID “ING2.4G_XXXXXXX” to pair [Step2].
PAGE 11
Step1 Step2 4.4 Ethernet Parameter Setting Procedures:    Tab on “Network”enter WAN Setting or LAN Setting menu. Enter WAN Setting to get and set the WAN parameter. Enter LAN Setting to get and set the LAN parameter. Step 1Step 2 4.5 WLAN Parameter Setting    Enter WLAN menu.[Step1] AXIUM DX8000-BASE-W2 has 2.4G WLAN and 5G WLAN,so we can click “2.4GHz WLAN” to set 2.4G parameter and click “5GHz WLAN” to set 5GHz WLAN.[Step2] We can set channel,RF power,band width and get WLAN MAC on the menu.
PAGE 12
Step 1 Step 2 Step 3 Step 4 4.6 Advanced Setting     Enter advanced menu. We can set the operating mode,DMZ and static DHCP of the base[Chart 1]. In operating mode,we can set the base work in different mode[Chart 2]. We can set DMZ[Chart 3]and add static DHCP[Chart 4]. [Chart 1] [Chart 2] [Chart 3] 4.7Operating Mode 4.7.1 Gateway Mode   ADSL/ONU distribute the IP to base ETH port. Base distribute the IP to DX8000.
PAGE 13
 ADSL/ONU and DX8000 are not in the same network segment . 4.7.2 Bridge Mode   Base distribute the IP to the computer and DX8000. They are in the same network segment . 4.7.3 WiFi Repeater Mode    It is a mode to expand coverage of base. For example , DX8000 is too far away to connect Base A. So we can put Base B between Base A and DX8000. Set Base B to repeat the Base A. DX8000 can connect to internet via Base B.
PAGE 14
4.8 Management Setting   In management menu, we can upgrade the firmware of base. First,we use software manager to install the wifidockfirmware.apk in DX8000,as follow :  Second,we pair the base with DX8000.We can get current version and lastest version information and click upload to upgrade the firmware[Step1]. Wait for upgrading.[Step2].And get the successful tips[Step3]. Check the version of the base[Step4].
PAGE 15
[Step1][Step2][Step3][Step4] 5. Fixing of the base In some scenes,we want to fix the base and the DX8000 to the table. The fixing structure is not standard configuration .We need to buy it from the agent. Installation procedures as below:  First,fix the space block on the table with screws.  Second,fix the Base Fixing structure on the space block with three screws.  Third,put the base on the structure to lock it.  Fourth,fix the Base Fixing structure on the base with three screws.
PAGE 16
 If we want to unfix the base and DX8000,we can use screwdriver to push the area of the structure to unfix them.
PAGE 17
6. FAQs Q1： The base fails to connect DX8000.  Cause1：DX8000 WLAN is not yet opened.  Solution：Open WLAN via the drop-down box of DX8000.  Cause 2：DX8000 is placed too far away from base.  Solution：Place and pair the devices within 10 meters.  Cause 3：The password of DX8000base is changed .  Solution：Input the correct password ,or restore factory setting to get the default password. Q2： It displays that base is not connected to DX8000, while the green indicator light of base flashes.
PAGE 18
Q5：Why mobile phone can not search the 5G WiFi?  Solution: Check whether mobile phone can support 5G WiFi. 7. Notes  Prevent the terminal from sun exposure, high temperature, moister and other mean conditions.  Cut off the power before cleaning the device and wipe the main body with dry cloth.  When the following abnormal phenomena occur, stop running the device immediately, cut off the power supply, and report to the service provider as soon as possible: 1） harsh noise heard during operation.
PAGE 19
10. Standard FCC WARNING This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
PAGE 20
Le présent appareil est conforme aux CNR d'ISED applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
PAGE 21
which can have an effect on the environment and human health. This Document is Copyright © 2020 by ingenico Group. ingenico retains full copyright ownership, rights and protection in all material contained in this document. The recipient can receive this document on the condition that he will keep the document confidential and will not use its contents in any form or by any means, except as agreed beforehand, without the prior written permission of ingenico.