Specifications

ManualsBrandsINGENICO ManualsPOS EquipmentSmart POS Terminal BASE

WWW.ingenico.com

28-32,boulevard de Grenelle, 75015 Paris - France/ (T)+33(0)1 58 01 80 00 / (F)+33 (0)1 58 01 91 35

Ingenico-SA au capital de 47 656 332 / 317 218 758 RCS Nanterre

Model:AXIUM EX-MBASE-W1

User Guide

Summary of content (17 pages)

PAGE 1
User Guide Model:AXIUM EX-MBASE-W1 WWW.ingenico.
PAGE 2
Contents 1. Product Introduction ......................................................................................................................................... 3 1.1 Open Package Inspection ............................................................................................................................ 3 1.2 Device Introduction ..................................................................................................................................... 3 1.
PAGE 3
1. Product Introduction 1.1 Open Package Inspection Open the package to check if there are any disabling masks or transportation damage in the terminals and fittings. Procedures： 1) Open the package 2) Check the following items(Subject to actual product configuration)  Base host  User Guide  12V/3.33 A power adapter  AC power cable  USB type-B cable  5 AXIUM EX8000 Bushings  5 AXIUM EX6000 Bushings 3) Save the transportation package and packing material for second use. 1.
PAGE 4
6 ETH_RX- 7 NC 8 NC 2） USB-TYPE B interface Sequence USB-TYPE BSignal 1 Not connect 2 D- 3 D+ 4 GND 2. Product Technology Features 2.1 Product Technology Specifications Port a DC JACK power port a RJ45 network port a USB B DEVICE port supporting USB2.0 Power Every Charge output: 5.0VDC 1.0A Power adapter: input 100-240V AC, 50/60Hz; output 12.0V DC 3.33A Size and Weight Size：311mmx127.8mmx91mm Net Weight：0.76kg Gross Weight：1.50kg 2.
PAGE 5
Atmospheric pressure 86kPa～106 kPa; Below 2000 meters above sea level 2.3 Product Functions The base has three main functions as below:  Place EX pos on the base to get charged.  Place EX pos on the base. Connect the USB type-B to computer to extend the USB port.  Serves as a router. EX pos can connect to the base via WiFi to extend the network. 2.4 Instructions  If AXIUM EX pos has the shell , we can place it on the base directlly.
PAGE 6
3. WiFi Connection 3.1 Connect EX pos to the base WiFi     Power on the base. Check the SSID and password from the label on the back of base. Click “Settings” menu on EX pos,and then click “Network and Internet”, enter “ Wi-Fi” and select the base SSID to connect.(step 1~4)  (WiFi Password please refer to the rear label for details) After that , EX pos can use the RJ45 network of the base. Step1 Step2 Step3 Step4 3.2 Web Setting of base The base can be set from the web.
PAGE 7
 User can get and change the Ethernet parameter on the Network page.  User can get and change the WLAN parameter on the WLAN page.
PAGE 8
 User canchange the operating mode,enable DMZ or set static DHCP on the Advanced page.  User can update the firmware of base, save and reload the settings, change the password on the Manage page.
PAGE 9
3.3 Restore factory Setting   4. Use sharp to click the RESET button for 3 seconds to restore the factory setting of the base. The position of RESET button is in chapter 1.2. BASE Setting From EX pos 4.1 Get the Admin permission     First,connect EX pos to the base via chapter 3.1. Click “Settings” menu on EX pos,and then click “Base”,input the Pairing Password[Step1].  (Pairing Password please refer to the rear label for details) Click the grey button beside the SSID “ING2.4G_XXXXXXX”[Step2].
PAGE 10
4.2 Ethernet Parameter Setting Procedures:    Tab on “Network”enter WAN Setting or LAN Setting menu. Enter WAN Setting to get and set the WAN parameter. Enter LAN Setting to get and set the LAN parameter. Step 1Step 2 4.3 WLAN Parameter Setting    Enter WLAN menu.[Step1] We can click “2.4GHz WLAN” to set 2.4G parameter and click “5GHz WLAN” to set 5GHz WLAN.[Step2] We can set channel,RF power,band width and get WLAN MAC on the menu.
PAGE 11
4.4 Advanced Setting     Enter advanced menu. We can set the operating mode,DMZ and static DHCP of the base[Chart 1]. In operating mode,we can set the base work in different mode[Chart 2]. We can set DMZ[Chart 3]and add static DHCP[Chart 4]. [Chart 1] [Chart 2] [Chart 3] 4.5 Operating Mode 4.5.1Gateway Mode    ADSL/ONU distribute the IP to base ETH port. Base distribute the IP to EX pos ADSL/ONU and EX posare not in the same network segment .
PAGE 12
4.5.2 Bridge Mode   Base distribute the IP to the computer and EX pos. They are in the same network segment . 4.5.3 WiFi Repeater Mode    It is a mode to expand coverage of base. For example , Ex pos is too far away to connect Base A. So we can put Base B between Base A and EX pos. Set Base B to repeat the Base A. EX pos can connect to internet via Base B. 4.6 Management Setting  In management menu, we can upgrade the firmware of base.
PAGE 13
 First,we use software manager to install the wifidockfirmware.apk in EX pos,as follow :  Second,we get the Admin permission of the base with EX pos via chapter 4.1.Wait for upgrading.[Step1].And get the successful tips[Step2]. Check the version of the base[Step3]. [Step1][Step2][Step3] 6. FAQs Q1： The base fails to connect EX pos.  Cause1：EX pos WLAN is not yet opened.  Solution：Open WLAN via the drop-down box of EX pos.  Cause 2：EX pos is placed too far away from base.
PAGE 14
7. Notes  Prevent the terminal from sun exposure, high temperature, moister and other mean conditions.  Cut off the power before cleaning the device and wipe the main body with dry cloth.  When the following abnormal phenomena occur, stop running the device immediately, cut off the power supply, and report to the service provider as soon as possible: 1） harsh noise heard during operation. 2） impurities or water found in the machine. 3） Unpleasant smell found during operation. 8.
PAGE 15
RF exposure The antenna of the product,under normal use condition is at least 20cm away from the body of theuser.Warning statement to the user for keeping 20cm separation distance and the prohibition of operating to a person has been printed on the user manual.So,this product under normal use is l0cated on electromagnetic far field between the human body. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
PAGE 16
L'antenne du produit, dans des conditions normalesd'utilisation, est à au moins 20 cm du corps de l'utilisateur. Unedéclarationd'avertissement à l'utilisateur pour maintenirune distance de séparation de 20 cm etl'interdictiond'opérer à unepersonne a étéimprimée sur le manuel de l'utilisateur. Ainsi, ceproduitenutilisationnormaleestlocalisé sur un champ électromagnétiqueéloigné entre le corps humain.
PAGE 17
nobody is authorized to place this document at the disposal of any third party without the prior written permission of ingencio. If such permission is granted, it will be subject to the condition that the recipient ensures that any other recipient of this document, or information contained therein, is held responsible to ingenico for the confidentiality of that information. Care has been taken to ensure that the content of this document is as accurate as possible.