4_6_2 Installing paper roll Open the paper compartment by lifting the catch located at the rear of the terminal and pull the cover to the rear of the terminal.
ADVICE If you insert a new R40 paper roll, tear off the first length (one complete turn to avoid printing on adhesive tape footprint). 5_Recommendations 5_1 Safety Powering down the Move/3500 : Disconnect the Move/3500 power supply block adapter from the electrical mains network. Lithium cell The Move/3500 is fitted with an internal lithium cell which can only be accessed by a qualified technician. Battery Move/3500 is fitted with battery specially designed for this terminal.
The power supply label contains seven symbols : Double insulation symbol DC current output AC current input DC Power jack polarity In door use only International Efficiency Marking Protocol (Energy Star Level 5) International Efficiency Marking Protocol (Energy Star Level 6) SAM1/SAM2/SIM1/(SAM3/SIM2) readers compartment The trapdoor for battery, SAM1/SAM2/SIM1/ (SAM3/SIM2), readers located underneath the terminal, must be in place during the normal operation of the terminal.
Electronic health appliances Your handset is a radio transmitter which may interfere with health appliances, such as hearing aids, pacemaker, hospital equipment, etc. Your doctor or the equipment manufacturer will be able to provide you with appropriate advice. External connection All external circuits connected to the Move/5000 must be SELV (Safety Extra Low Voltage) and LPS (limited power source) within the meaning of section 2.2 and 2.
_3 Fixed installation If the device is to be used in a situation where it is not possible for the cardholder to pick up and shield their PIN entry themselves, the device may be used without PIN shield, but it must be installed in the following manner: a) The device must be angled at 45 or more, so that oversight of the PIN entry from the rear of the device is not possible.
_Standards 6_1 Environment (WEEE, Batteries and Packaging) This product is labeled in accordance with European Directives 2002/96/EC concerning Waste Electrical and Electronic Equipment (WEEE) and 2006/66/EC concerning Batteries and Accumulators. Those provisions are requiring producers and manufacturers to become liable for take-back, treatment and recycling upon end of life of equipment and batteries.
6_2 FCC/IC Compliance You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
Les dispositifs fonctionnant dans la bande de 5 150 à 5 250 MHz sont réservés uniquement pour une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux. D’autre part, les utilisateurs de radars de haute puissance sont désignés utilisateurs principaux (c.-à-d.
The REN is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local telephone company.
7_Troubleshooting The terminal does not turn on Check the battery ( is it discharged ?, is it connected ?) A full discharged battery can take long charging time to recover Connect terminal to terminal power supply or put it on powered base Cards are not read Check that the magnetic card is swiped correctly (with magnetic band on terminal side).
“This Document is Copyright © 2018 by INGENICO Group. INGENICO retains full copyright ownership, rights and protection in all material contained in this document. The recipient can receive this document on the condition that he will keep the document confidential and will not use its contents in any form or by any means, except as agreed beforehand, without the prior written permission of INGENICO.
