45532694 Edition 2 August 2007 Doser - Docking Station Maintenance Manual
INDEX 1 DOCKING STATION – DS .................................................................................... 3 1.1 Dismounting the Docking Unit .............................................................................................................3 1.2 Change Pneumatic Clamps ..................................................................................................................4 1.3 Change Male Docking Valve Complete .....................................................................
1 Docking station – DS Use the drawings and the component list for the specified unit. In the description below, the figures below (xx) refer to the corresponding figures on the drawing. Always turn off the air and material supply & depressurize the entire system before installing, removing or adjusting any accessory on this product, or before performing any maintenance on this product or any accessory. Failure to follow these instructions can result in personal injury. 1.
1.2 Change Pneumatic Clamps Drawings/ Component lists: • Aut. Tool Changer DS Docking unit DS-ATC complete T2X-16-502-IR T2X-16-500-IR/-505-IR • Aut. Tool Changer- (onboard lub.) DS Docking unit DS complete T2X-16-503-IR T2X-16-501-IR a) Follow step a) to e) in section 1.1. The docking station can be turned 180° and place back in the same place. • Disconnect electric contacts and remove pneumatic hoses on clamp unit.
1.3 Change Male Docking Valve Complete • Drawings/Component lists: T2X-16-500-IR/-501-IR/-505-IR T2X-16-502-IR/-503-IR T2X-16-511-IR This operation requires, the following special tools and preparations: • Mounting paste a) Remove the cover plate (9) by removing the three screws (14). • Take off the docking unit (1) by removing the four nuts and washers (16 and 17). b) It is recommended to remove one of the clamps before continuing the dismounting of the docking valve.
1.4 Hydraulics of the Docking Station Drawing/Component list: • • • • DS ATC DS ATC (OnBoard Lubrication) Docking Unit ATC Docking Unit (Onboard lub.) T2X-16-500-IR/-505-IR T2X-16-501-IR T2X-16-502-IR T2X-16-503-IR For doser hydraulics and pneumatics, See “Doser” Maintenance Manual Form 45532660. NOTE! Only lubrication of inlet valve for OnBoard Lubricetion.
1.5 Pneumatics of the Docking Station Drawing/Component list: • • • • DS ATC DS ATC (OnBoard Lubrication) Docking Unit ATC Docking Unit (Onboard lub.
1.6 Male Docking Valve • Drawing/Component list: T2X-16-511-IR Use the drawings and the component list for the specified unit. In the description below, the figures (xx) refer to the corresponding figures on the drawing. 1.6.1 Dismantling of the Male Docking Valve This operation requires, the following special tools and preparations: • A T2000-17-005-IR to compress the spring (two threaded rods and a bracket with three holes). • A flat, 7mm, fork spanner.
1.6.2 Assembly of the Male Docking Valve This operation requires, the following special tools and preparations: • A T2000-17-005 to compress the spring (two threaded rods and a bracket with three holes). • A flat, 7mm, fork spanner. • Screw locking liquid - Loctite 270 • Special high temperature grease for the sealings, Uniway LIX 625.
m) Place the cylinder (3) on the piston, (4). Align it, and press it into the housing. n) Position all parts on the docking valve according to the drawing. Tighten the four screws (19). Torque is 10 Nm. o) Finally, the pneumatic unit function should be tested. Connect the air and check the movement of the needle. 1.7 Female Docking Valve See “Doser” Maintenance Manual form 45532660.
Length in mm =cable 1.8 Electrical contacts in docking station. Från nr. Name WH - 18 XP62/19 Poles WH -17 XP62/19 POLES WH - 16 XP62/19 POLES Heater/inlet valve Heater/inlet valve WH - 4 XP62/19 POLES WH - 14 XP62/19 POLES T2X-nr. Se drawing: T2X-SF-008- T2X-20-029-IR,sheet IR 302.0 T2X-SF-008T2X-20-029-IR,sheet IR 3021 Till (nr) Name T2X-nr. Se drawing: T2X-SF-005- T2X-20-029-IR,sheet IR 302.0 Comments WH - 18 XP61/36POL WH - 17 XP61/36POL T2X-SF-005- T2X-20-029-IR,sheet IR 302.
www.irtools.