Soft Camera Pack
ENGLISH
1.
2. Start to use 2.1 Battery installation Open the battery cover follow the picture below, mount two AAA (LR03) alkaline batteries according to the correct direction (there are + - polarity hints inside the metal sheet of the battery cover), then close the battery cover. Then press Power/Menu key to start up. After starting up, if the camera settings will be changed, please refer to the content of this manual.
2.3 Sleep mode (automatic shutdown-power saving mode) The camera will enter sleep mode automatically if there is no operation for successive 30 seconds. Press Power/Menu key for 3 minutes and the camera will enter sleep mode. Under sleep mode, the camera consumes very little power. Please press Power/Menu key to exit sleep mode. 2.4 Switching function mode Press Power/Menu key to display menu interface and then press Up key for selection.
Record short video Continuous shooting Icon Select resolution Mode 5M,2592×1944 VGA,640×480 QVGA,320×240 4
Icon Mode Without compressing mode Compression ratio Compressing mode Icon Mode 50Hz Power frequency 60Hz 5
Delete all Electric quantity of battery Icon Electric quantity >70% >35% >5% <=5% 6
2.5 Self-portrait/record AVI short video/continuous shooting mode Press Power/Menu key once and select the first icon, then press Shutter key to switch among “single shooting-->self-portrait-->record AVI short video-->continuous shooting” mode. Press Power/Menu key again to enter selected mode. Self-portrait Record AVI short video Continuous shooting 2.6 Resolution setting Press Power/Menu key and Up key until the resolution icon is selected.
2.8 Power frequency setting Press Power/Menu key and Up key until the power frequency icon is selected. Then press Shutter key to select 50Hz or 60Hz (consistent with the local AC power frequency), press Power/Menu key to enter the selected mode. 2.9 Delete all the files in camera (formatting) Press Power/Menu key and Up key until the delete all icon is selected. Then press Shutter key to get into enter menu, moreover, press Up key for selection and finally press Shutter key for confirmation. 3.
3.1 Camera driving installation Click button and finish installation step by step according to the hints. Please restart the computer after finishing installation. Note: it is prohibited to connect the camera with the computer before installing the driving to avoid error of driving installation. 3.2 ArcSoft PhotoImpression picture editing software installation Click button and install according to the hints, please restart the computer after finish installation.
Click button “picture download” and the file in camera will display in the window in form of small figure. Click the small figure with the right key of mouse to amplify the display, then click the amplified or reduced display window with the right or left key. Click button “select all the pictures” and then click button “picture storage” the files to the computer.
3.4 Storage of interpolation pictures with 5.20 million pixels A: Before storage, click image adjustment button ; B: Select “digit amplification” option and then confirm. C: Then the pictures with VGA format can be downloaded as interpolation pictures with 5.20 million pixels as the description above. 3.
4. Answer Your Questions Failure to start up by pressing the power key --The electric quantity of power is too low, please change battery. Please notice to utilize the alkaline battery. Failure to download pictures --Restart the computer and reconnect to download. --Ensure that the camera driver is in normally installed. --If the driver has been installed, please ensure that no software is using the camera function.
640 X 480 pixel (VGA) 320 X 240pixel (QVGA) -Storage volume: 1.3 M format 15 pictures (30 for compression mode) VGA format 46 pictures (70 for compression mode) QVGA format 100 pictures (138 for compression mode) -File format: picture-JPEG Short video-AVI -Fittings: USB wire, ArcSoft PhotoImpression picture editing software, manual -Operation system supported: Microsoft Windows 2000, XP, VISTA, 7 6.
Warning 1. Before taking pictures, please try to take several pictures first to ensure that the camera is in normal working condition. The company is not responsible for any loss rising from camera fault. 2. Strong electrostatic will influence the normal application of the camera; under such circumstances, please cut off the power and restart.