User's Manual
Please read the instructions carefully before using the speaker.
Please make sure the battery is charged before using the speaker.
Please Keep this manual for future access problems.
P
leas
e re
a
d the in
s
truction
s car
e
fully b
efore u
sing the speake
r.
Please mak
e
sure th
e bat
t
ery is
ch
a
rge
d
b
ef
o
r
e
usin
g
the
spea
ker.
P
lea
se Keep
th
is ma
n
ual for
fu
ture acce
ss
p
ro
b
le
ms.
Open the box
a. a bluetooth speaker
b. USB Cable
c. a user manual
d. a 3.5mm audio cable
bluetooth speaker user manual audio cable
Built-in Bluetooth
Built-in lithium battery
TF card /SD Play (MP3)
3.5MM line output jack
TWS function
IPX6 water insistence
FUNCTIONS
Technical parameters
Speaker Size : 2" 4Ω*1
R. Frequency : 2402-2480 MHZ
S/N Ratio : 86db
Lithium Battery : 3.7V 800mAh
Play time (80% Volume) : 2 Hours
Charging Time : 2 Hours
Dimension : 150.96*80.99*80.35mm
Once open the speaker, it will turn to Bluetooth directly. Double click “M” switch to IF /SD mode, double click “M” switch to Aux in.
Play/ pause: short press “M” button for play or pause music.
“+”: Short press for Volume Up, long press for Next song.
“-”: Short press for Volume down, long press for previous song.
TWS: Turn two speaker on, then double click one speaker “-“ for TWS connect.
You will hear the voice prompt means TWS connect successful. You can connect one Bluetooth from one of them to start.
Turn on/off: Long press for turn on or turn off.
The product should not be subjected to water or water splashing, should not be placed in some objects such as vases filled with liquid
Keep the product away from vases, buckets, wash bowls. If the liquid poured into the product
Do not use the product which be placed in high temperature environment (such as an ignition source, oven or similar environment)
Do not use the product which be placed in very humid or steam filled environment
When you move the product from a cold environment to a hot environment, if the product interior
already with moisture, will not work. At this time, turn on the power to wait for about an hour,it can work normally after all moisture evaporation.
1.Power on speaker A
2.Turn your phone Bluetooth on, pair and connect to the Bluetooth speaker. The device will be listed in Blue text under the topic PAIRED DEVICES.
3.Power on speaker B, double press “-” button then speaker B can connect to your phone at the same time
speaker A phone speaker B
Please make sure the following accessories are safe
BLUETOOTH –TF—AUX in mode shift.
USB Cable
Output Power: RMS 5W
OPERATION HIGH TEMPERATURE OR HUMIDITY
TWS Function -- One Phone with Two Speakers for Stereo Sound
Attention : Our company retained the power that change the design and specifications for improve the product.
Please kindly understand that we will not notice in further.
AVOIDING WATER
AUX TF
/M
DC IN
材质：110*80mm
材质：80G单黑双面印刷
The device can be used in portable exposure confition without restriction.
Federal Communications Commission (FCC) Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any
interference
received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
●Reorient or relocate the receiving antenna.
●Increase the separation between the equipment and receiver.
●Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
●Consult the dealer or an experienced radio/TV technician for help.
Warning: Changes or modifications made to this device not expressly approved by Wantai Future
Electronic Technology (Guangzhou) Company Limited may void the FCC authorization to operate
this device.
Note: The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modifications to this equipment. Such modifications could void the user’s authority
to operate the equipment.