Installation Instructions

Connector Assignments
Wiegand / Clock & Data / TTL serial
1
D1 / DATA
TXD
3
BUZZER
RXD
5
GND
2
D0 / CLOCK
4
LED
6
POWER
RS485 / RS422
1
RS485 TRX-
RS422 TX-
3
RS485 N.C.
RS422 RX+
5
GND
2
RS485 TRX+
RS422 TX+
4
RS485 N.C.
RS422 RX-
6
POWER
Caution: floating communication lines may cause spurious emissions.
Ensure all communication lines are properly biased and terminated.
RS232
1
TXD
3
RTS
5
GND
2
CTS
4
RXD
6
POWER
Installation instructions
1 Determine an appropriate position for the reader
and drill two holes for mounting the backplate
and one hole for the cable, see diagram for
measurements. Do not mount readers less than
20 cm (8 inches) apart.
2 Pull the cable trough the hole in the backplate
and mount the backplate. Protect the cable
against sharp edges and any damage from
chafing.
3 Prepare the end of the cable and wires, eliminate
any loose or frayed strands. Keep the wire ends
as short as practical.
4 Connect the wires to the connector according to
the reader type. Wire ends and optional
permanent links shall be kept as short as
possible.
5 Place the reader front over the hinge of the
backplate and close the reader (see diagram),
keeping the wiring in the lower part of the reader
housing. DO NOT use excessive force, retract the
cable if necessary.
6 Test the reader: apply power and present a valid
card. The LED bar should flash and the sounder
should produce a short tone indicating a
successful read. If the Host system is connected
to LED bar and sounder inputs these should
follow the functionality of the Host system.
7 The reader front should now be secured to the
backplate using the supplied enclosure screw.
Configuration
The reader is factory configured to read H-PX cards.
For other cards and output formats, refer to the
enclosed SmartProx quick reference guide Card and
output selection configuration sheet.
Certifications
FCC, IC
FCC ID: YAB-NGRPSPX
IC: 8908A-NGRPSPX
Warning (part 15.21)
Changes or modifications not expressly approved by the
party responsible for compliance could void the user’s
authority to operate the equipment.
For mounting, use only flat head screws with a maximum
shank size of 4 mm (5/32”, #7)
Compliance statement (part 15.19)
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
Le présent appareil est conforme aux CNR d’Industrie Canada
applicables aux appareils radio exempts de licence. L’exploitation
est autorisée aux deux conditions suivantes :
(1) l’appareil ne doit pas produire de brouillage, et
(2) l’utilisateur de l’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement.
Information to the User (Part 15.105 (b))
Note: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of
the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
Complies with: CAN ICES-3 (B)/NMB-3(B)
INID SmartProx readers - installation and operation manual version 1.05; March 28, 2014
INID BV
Mariëttahof 27
2033 WS Haarlem
The Netherlands
Phone: [phone]
Web: www.inid-readers.com