Installation Manual

ManualsBrandsInjen ManualsAir IntakeInjen Technology SP1477BLK Black Mega Ram Cold Air Intake System

Part number SP1477

02-06 Acura RSX Type-S

1- cold air intake system

1- 3” Injen filter (#1014)

1- 2 7/8” x 3” 60 deg. elbow (#3007)

1- 1525 sensor grommet (#6014)

1- 20”- 8mm vacuum hose (#3091)

1- 18”- 17mm vacuum hose (#3080)

2- Power-Bands (.362) .048 (#4004)

1- RSX Long vibra-mount (#6029)

1- M6 flange nut (#6002)

1- fender washer (#6010)

1- custom roto-molded windshield

reservoir tank (#6027)

m6 x m25 bolts (For reservoir tank) (#6006)

2- fender washers

(for reservoir tank) (#6010)

1- instructions

Note: This intake system was

specifically designed and

tested with this filter element.

Buy replacement parts on-line at

“injenonline.com”

Congratulations! You have just purchased the best engineered,

dyno-proven cold air intake system available.

Report any defective or missing parts to the Authorized Injen

Technology dealer you purchased this product from.

Before installing any parts of this system, please read the instructions

thoroughly. If you have any questions regarding installation please

contact the dealer you purchased this product from.

Installation DOES require some mechanical skills. A qualified

mechanic is always recommended.

*Do not attempt to install the intake system while the engine is hot.

The installation may require removal of radiator fluid line that may

be hot.

Injen Technology offers a limited lifetime warranty to the original

purchaser against defects in materials and workmanship. Warranty

claims must be handled through the dealer from which the item was

purchased.

Injen Technology 244 Pioneer Place Pomona, CA 91768 USA

Please check the contents of this box immediately.

Note: This intake system was Dyno-tested with an Injen filter and

Injen parts the use of any other filter or part will void the

warranty and CARB exemption number.

Parts and accessories are available on line at “Injenonline.com”.

Note: Install the intake while in 5th gear, this will put the change lever at its furthest point for clearance.

Now available, Hydro Shield by Injen

Part Number X-1033

Hydro Shield Sold Separately

Summary of content (5 pages)

PAGE 1
Part number SP1477 02-06 Acura RSX Type-S 11111121111- cold air intake system 3” Injen filter (#1014) 2 7/8” x 3” 60 deg. elbow (#3007) 1525 sensor grommet (#6014) 20”- 8mm vacuum hose (#3091) 18”- 17mm vacuum hose (#3080) Power-Bands (.362) .
PAGE 2
<<< Arrows indicate where fasteners are located Removal of the head light is not required. Diagram to help aid in the removal of the front bumper. Diagram 1 Washer reservoir removal (A) (A) (B) (B) (A) (A) remove the 2 pin connectors and washer tubes (B) Front washer motor >>> Rear washer motor >>> Remove the three m6 bolts holding the reservoir tank in place (A). Remove the 2 pin connector pins from the two washer motors (B). Remove the stock reservoir bottle from the car frame.
PAGE 3
(A) (A) This is the location of the vibra-mount prior to setting the reservoir tank in place. The tank is placed under the vibra-mount, this is for demonstration of the location only (A). The opening that leads into the engine compartment when installing the intake(B). >> >> >> >> >> >> (B) (B) The battery tray is removed from the RSX (A). Turn the battery tray upside down and drill the two tacked or spot welded areas until the bracket becomes loose (B).
PAGE 4
>>> >> >> >> >> (B) > >> >> > >> >> (A) >> (A) (C) > Use the m6 x m25 bolts and fender washers to secure the two extended legs on the reservoir tank (A). Plug the harness clips into the stock motors (B). Reconnect the stock rear and front lines to the original motors pumps (C). Press the 2 7/8” end of the molded elbow over the throttle body. Position the elbow downward and semi-tighten one of the clamps on the elbow.
PAGE 5
Note: Removal of the entire battery and battery tray will be required for this installation. 1. Once the installation is complete, reconnect the negative battery terminal before you start the engine. 2. Align the entire intake system for the best possible fit. Once the intake has been properly fitted continue to tighten all nuts, bolts and clamps. 3. Periodically, recheck the alignment of the intake system and make sure there is proper clearance around and along the length of the intake.