Owners manual

ManualsBrandsINJEN ManualsAutomotiveInjen SP1726BLK Cold Air Intake System Fits 03-06 Element

Part number SP1726

2003-06 Honda Element

2.4L, 4 cyl.

1- 2 pc. Injen cold air intake (CV)

1- 3” Injen filter (#1014)

1- 2 3/4” straight hose (#3043)

1- 3” straight hose (#3044)

1- 1 1/8” x 2” CCV hose (#3112)

1- 1525 sensor grommet (#6014)

2- Power-bands (.312) .040 (#4003)

2- Power-bands (.362) .048 (#4004)

2- mini-clamps .016 (#4027)

1- m6 vibra-mount (#6020)

1- M6

male/female vibra-mount (#6028)

2- M6 flange nut (#6002)

2- fender washer (#6011)

1- instruction

Note: Injen Technology parts and

accessories are now sold on

line at:

“injenonline.com”

Congratulations! You have just purchased the best engineered,

dyno-proven cold air intake system available.

Please check the contents of this box immediately.

Report any defective or missing parts to the Authorized Injen

Technology dealer you purchased this product from.

Before installing any parts of this system, please read the instructions

thoroughly. If you have any questions regarding installation please

contact the dealer you purchased this product from.

Installation DOES require some mechanical skills. A qualified

mechanic is always recommended.

*Do not attempt to install the intake system while the engine is hot.

The installation may require removal of radiator fluid line that may

be hot.

Injen Technology offers a limited lifetime warranty to the original

purchaser against defects in materials and workmanship. Warranty

claims must be handled through the dealer from which the item was

purchased.

Injen Technology 244 Pioneer Place Pomona, CA 91768 USA

Please check the contents of this box immediately.

Note: This intake system was Dyno-tested with an Injen filter and

Injen parts the use of any other filter or part will void the

warranty and CARB exemption number.

Parts and accessories are available on line at “Injenonline.com”

Note: The installation of this cold air intake does require mechanical skills. Removal of the front bumper requires

loosening and removing several plastic plugs and screws that may be difficult. In addition to removing the

bumper, you will also have to remove the air resonator box, battery and tray when beginning this installation.

Injen strongly recommends that this system be installed by a professional mechanic.

MR Technology, “The World’s First Tuned Intake System!”

Optimum performance, Factory safe air/fuel ratio.

“An air intake evolution”

Cold air intake

Converts to short Ram

Tools required:

1. Flat head screwdriver

2. Ratchet

3.10mm socket

4. 8mm socket

Summary of content (4 pages)

PAGE 1
Tools required: 1. Flat head screwdriver 2. Ratchet 3.10mm socket 4. 8mm socket Part number SP1726 2003-06 Honda Element 2.4L, 4 cyl. 11111122211221- 2 pc. Injen cold air intake (CV) 3” Injen filter (#1014) 2 3/4” straight hose (#3043) 3” straight hose (#3044) 1 1/8” x 2” CCV hose (#3112) 1525 sensor grommet (#6014) Power-bands (.312) .040 (#4003) Power-bands (.362) .048 (#4004) mini-clamps .
PAGE 2
Prior to starting this installation, disconnect the negative battery terminal. (A) >>>> Loosen clamps and bolts in order to remove the air intake duct and air intake box from the engine compartment. Prior to pulling the air box out, remove the 8mm breather hose (A). Note: For this installation, it will be required to remove the front bumper. Once the bumper has been removed continue to remove the stock air intake resonator from the bumper area.
PAGE 3
(B) >> >> (A) >> >> >>> > >> >> (B) (A) Once the CCV hose has been positioned Take the 1 1/8” ID CCV hose, place two mini-clamps on each end of the CCV hose as shown above (A). Press the CCV hose correctly, continue to tighten the lower clamp(A). Now press the CCV box over and into the CCV over the large intake port as shown above. hose as shown above (B). Once the CCV box has been correctly installed continue to tighten the mini-clamp.
PAGE 4
(B) >> >> >> >> (A) Insert the top end of the intake into the 3” hose (A) Line Press the filter over the end of the intake and tighten Locate the secondary intake and insert it into the bumper area via the engine compartment between the up the intake bracket to the vibra-mount stud (B). Tighten the filter neck clamp. Align the entire intake for best the m6 flange nut and fender washer to the VM stud (B). fit then continue to tighten all nuts, bolts, and clamps. battery and front cross member. 1.