Installation Manual

ManualsBrandsInjen ManualsAir IntakeInjen Technology SP1978P Polished Mega Ram Cold Air Intake System

Part number SP1978

2004-06 Nissan Atima V6 3.5L

New MR Technology

1- MR Tech 2 piece cold air intake

1- 3 1/2” inverted cone filter (#1021)

1- CCV Breather Box w/ 1 port (#6060)

1- 3” straight hose (#3044)

1- 3 1/8” straight hose (#3054)

1- 1 1/8” x 2” coupler hose (#3112)

4- Power-Bands (.362) .048 (#4004)

2- Mini-bands .016 (#4027)

1- M6 Vibra-mount (#6020)

1- M6 flange nut (#6002)

1- Fender washer (#6010)

1- T-20 torx bit (#6021)

1- Instruction

Note: Filters, Hydro-shields, accessories

and Pro-Tech filter charger kits are

sold on “injenonline.com”

Congratulations! You have just purchased the best engineered,

dyno-proven cold air intake system available.

Please check the contents of this box immediately.

Report any defective or missing parts to the Authorized Injen

Technology dealer you purchased this product from.

Before installing any parts of this system, please read the instructions

thoroughly. If you have any questions regarding installation please

contact the dealer you purchased this product from.

Installation DOES require some mechanical skills. A qualified

mechanic is always recommended.

*Do not attempt to install the intake system while the engine is hot.

The installation may require removal of radiator fluid line that may

be hot.

Injen Technology offers a limited lifetime warranty to the original

purchaser against defects in materials and workmanship. Warranty

claims must be handled through the dealer from which the item was

purchased.

Injen Technology 244 Pioneer Place Pomona, CA 91768 USA

Please check the contents of this box immediately.

Note: This intake system was Dyno-tested with an Injen filter and

Injen parts the use of any other filter or part will void the

warranty and CARB exemption number.

Parts and accessories are available on line at “Injenonline.com”

Note: The installation of this cold air intake does require mechanical skills. Removal of the front bumper requires

loosening and removing several plastic plugs and screws that may be difficult. It is recommended that this

system be installed by a professional mechanic. Be sure to disconnect the negative terminal before proceeding.

Congratulations! You have just purchased the worlds first tuned intake system.

MR Technology, Leading the way!

Tools required:

1. Ratchet and extension

2. 10mm socket

3. Phillips screwdriver

4. Flat head screwdriver

5. Pliers

6. 8mm nut driver

Fig. 1

Pipe and filter in this

application

Hydro-shield used on this

application X-1037

Summary of content (4 pages)

PAGE 1
Tools required: Part number SP1978 2004-06 Nissan Atima V6 3.5L New MR Technology 1111114211111- MR Tech 2 piece cold air intake 3 1/2” inverted cone filter (#1021) CCV Breather Box w/ 1 port (#6060) 3” straight hose (#3044) 3 1/8” straight hose (#3054) 1 1/8” x 2” coupler hose (#3112) Power-Bands (.362) .048 (#4004) Mini-bands .
PAGE 2
Fig. 2 Remove the four m6 bolts that secure the engine cover over the intake manifold. Once all bolts have been removed, continue to remove the engine cover. Fig. 3 Fig. 4 Remove plastic expanding plugs holding the front air scoop over the radiator. Once all plugs have been removed, continue to remove the air scoop. Loosen clamps and remove bolts from the stock air intake box cleaner in order to remove the entire air cleaning assembly. >> >> Fig. 5 Fig.
PAGE 3
(B) >> >> CCV hose (A) >> CCV box >> Fig. 11 Fig. 12 Insert the 1 1/8” CCV hose over the CCV box large port. Use the mini-bands to secure the hose in place, tighten the band on the CCV box port at this time. Press the assembled CCV box over the large intake port as shown above (A). Adjust entire CCV box and the tighten mini-band on the intake port (B). Fig. 13 Press the stock breather hose over the open CCV box port as shown above. Fig. 14 Fig.
PAGE 4
Fig. 21 Fig. 22 Press the 3 1/2” filter over the end of the secondary intake and tighten the clamp on the filter neck. Congratulations! You have just completed the installation of The World’s First Tuned Intake. Periodically, check the cold air for fitment in order to avoid any damage to your intake. 1. Upon completion of the installation, reconnect the negative battery terminal before you start the engine. 2. Align the entire intake system for the best possible fit.