User's Manual

1. Turn on the device.
2. Connect your phone to a 2.4GHz Wi-Fi network.
3. Open the app and click “Add device” to select “Phoenix”.
4. Choose to connect via Wi-Fi.
5. Confirm that the Wi-Fi icon on the device flashes slowly, then select AP mode.
Note: If the Wi-Fi icon doesn't flash slowly, press the button and hold for 3
seconds to reset Wi-Fi or change the Wi-Fi connection mode. It will take 5
seconds to implement this action.
6. Enter the Wi-Fi password on the app and click Next Step to continue.
7. Enter your phone’s WLAN setting page and select “SmartLife-xxxx” to connect.
8. Go back to the app and confirm to continue.
9. When the connection is complete, the application will display "Match success-
ful!" and the Wi-Fi icon will remain lit.
Notes:
1. After connecting the phone to Wi-Fi, the device will connect to the cloud server.
As long as the phone has Internet access (mobile data or any Wi-Fi), the user can
remotely monitor the device and view the data anytime and anywhere through the
App.
2. The device has the function of protecting Wi-Fi from misoperation. When the
device is successfully connected to the user's mobile phone, the device will
remember the Wi-Fi configuration information (Wi-Fi name and password) and
connect automatically.
You can press the button and hold for 3 seconds to reset the Wi-Fi network
and configure a new Wi-Fi network. It will save the changes within 3 minutes. The
device will reconnect to the previous Wi-Fi network in the following two cases:
1) After 3 minutes of device connection failure, a new Wi-Fi network restarted.
2) After resetting, the device shuts down without Wi-Fi configuration.
3. Removing the device from the application will completely clear the network
configuration information (Wi-Fi name and password), and the device will not
reconnect to the Wi-Fi network in any previous case.
4. Please keep as close to the equipment as possible. When connecting to a
wireless router using Wi-Fi, the signal becomes weak, and the connection fails if
the device is far away.
5. Please keep as close to the equipment as possible. When connecting to your
phone via Bluetooth, the signal becomes weak, and the connection fails if the
device is far away.
6. If the device is placed on a metal table or near a metal object, the signal will be
weakened, and the device will not be able to connect to the network or your
phone.
7. This device only supports 2.4GHz Wi-Fi networks, but it’s also compatible with
Wi-Fi 4, Wi-Fi 5, Wi-Fi 6, and Wi-Fi 6E routers only if they are enabled 2.4GHz Wi-Fi
channels.
8. This device only supports WPA/WPA2 encryption. If the router is set to any
other encryption method, the device will not be able to connect to the Wi-Fi
network.
Model: Phoenix
Size: 88 * 88 * 33 mm
Net Weight: 145 G
Screen Size: 53 X 35mm
Screen Type: VA LCD
Magnetic Class: N30
Battery Type: Lithium-Ion Polymer
Battery
Battery Capacity: 2500mah/ 9.25WH
USB Type-C Input Voltage: DC 5V
USB Type-C Input Current: Standard 1A
Operating Temperature: 0℃~55℃/32
℉~131℉
Temperature Unit: ℃/℉
Temperature Calibration Range: -7℃ to
+7℃/-12.6℉ to +12.6℉
Response Time: 0.1 seconds (min)
Temperature Refresh Rate: 4Hz
High/Low-Temperature Alarm: the device and the application will alarm
simultaneously
Alarm Mode: single trigger mode or repeated trigger mode.
Alarm Interval: alarm interval can be set in repeated trigger mode.
Probe Connector: jack 2.5mm mono plug 11mm
Number Of Detection Channels: 4
System Requirements: android 7.1 or later, iOS 11 or later
Short-Time Temperature Measurement Range: -30℃~+300℃/-22℉~+572℉
Continuous Temperature Monitoring Range: -20℃~+250℃/-4℉~+482℉
Probe Temperature Resolution: 0.1℉
Probe Temperature Accuracy: ±0.5 °C (maximum) +25 °C to +140 °C
±1.0 °C (maximum) 0 °C to +185 °C; ±1.5℃ (maximum) from -10℃ to +250℃
±2.0℃ (maximum) from -20℃ to +300℃
17