USER GUIDE LED LIGHTED RECESSED MEDICINE CABINET – WITH SURFACE-MOUNT KIT Model: 69252235, 69353035, 69354235
IMPORTANT SAFETY INFORMATION Please read through this installation instruction so you will know how to install and operate your model properly. Keep this document in a safe place for future reference after use. WARNING This product must be installed in accordance with the installation instruction by qualified technician. Failure to follow instruction could result in death or serious bodily injury. CAUTION This product must be serviced by qualified personnel.
INSTALLATION Recessed Mount Surface Mount W a a L 3/4" ❷ ❷ d b b 5/8” h h L c ❶ ❶ a b c d h L W 69252235 21" 34" 4" 2-1/2” 18" 20" 21" 69353035 29" 34" 4" 2-1/2” 18" 28" 29" 69354235 41" 34" 4" 2-1/2” 18" 40" 41" ❶ Electrical wire from GFCI Blank Face to be connected to the built-in outlet receptacle. (For the built-in outlet receptacle, rating: 20A 125V AC 60Hz, Class 2 Output: 5VDC Max 4.
INSTALLATION Remove the Mirror Door Hinge Hinge Plate Mirror Door Cabinet Remove the Electrical Box Unplug the cable from the Mirror Door to Electrical Box. Remove the Mirror Door by pulling on the tab behind the Hinge to detach the hinge from the Hinge Plate. Take out the electrical box by removing the 2 screws underneath. For Surface Mount ONLY 1. Install upper mounting brackets a. Insert brackets from the cutaway at the center of the upper grove. b. Install one bracket to the wall at each end.
INSTALLATION For Surface Mount ONLY (continue) 2. Install the lower mounting bracket a. Slide the bracket into the grove at the bottom of the cabinet towards the back. b. Mount the bracket to the wall. For Recessed Mount ONLY Secure the cabinet to the frame Secure the cabinet to the frame as shown above. Customer Service: (866) 479-8076 or customerservice@innoci-usa.
INSTALLATION Wiring ❷ ❶ 1. Route the wire into the cabinet. 2. Insert electrical wire from GFCI Blank Face to the corresponding outlet receptacle prewired quick connectors (Black Cable) in the electrical box. 3. Insert electrical wire with constant 110V/60Hz AC or from a wall switch to the corresponding LED lights prewired quick connectors (White Cable) in the electrical box. 4. Reinstall the electrical box.
INSTALLATION Install the Glass Shelves Shelf Pin Glass Shelf Insert Shelf Pins to desired height. Slide the Glass Shelf into position and tighten the plastic set screw (A) Reattach the Mirror Door(s) and reconnect the power supply cables to the Electrical Box. BASIC OPERATIONS Touch switch a. b. Press the switch once to turn on/off the LED lights. When the lights are on, press and hold the switch for about 3 seconds to change the color temperature.
CARE AND MAINTENANCE Clean the mirror with a soft, damp cloth and dry thoroughly with a soft towel. Do NOT allow the edges of the mirror to get or remain wet over a period of time. Please do NOT use glass cleaner that contains ammonia or vinegar. Never spray any cleaner directly onto a mirror. Instead apply the cleaner to a soft cloth and then wipe the mirror. Make sure no commercial cleaner comes in contact with the edge or backing.
EXPLODED VIEW Part Description 1 Mirror Door 2 LED Light 3 Connection Box 4 LED Driver 5 Touch Switch 6 110V Receptacle with USB Outlets 7 Cover Plate 8 Cosmetic Mirror 9 Aluminum Frame 10 Glass Shelf 11 Mirror Back Board 12 Hinge 13 Side Mirror (Sold Separately) Customer Service: (866) 479-8076 or customerservice@innoci-usa.
innoci usa, Inc. 14530 Best Ave., Santa Fe Springs, CA 90670 www.innoci-usa.com © innoci usa, Inc. All rights reserved. Rev 3.