IG04 BACnet Gateway / Vaisala WXT/WMT INSTALLATION INSTRUCTIONS
Proprietary No part of this technical manual may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, without prior written permission of Mass Electronics Pty Ltd. Trademark The term ‘Innotech’ used in this manual is a trademark of Mass Electronics Pty Ltd trading as Innotech Control Systems Australia.
Contents Proprietary......................................................................................................................... 2 Trademark.......................................................................................................................... 2 Disclaimer.......................................................................................................................... 2 Overview...........................................................................................
Installation Instructions for Innotech IG04 BACnet Gateway and Vaisala Transmitter / Sensor Overview This document provides instructions to connect a Vaisala device to the IG04 BACnet Gateway, and configuring the Vaisala device and IG04 using the embedded web server and the FusionLIVE Java application. Detailed instructions are provided to help you access the embedded web server, and easily configure the IG04 and Vaisala device.
Installation Instructions for Innotech IG04 BACnet Gateway and Vaisala Transmitter / Sensor Wiring Using The 8-Pin M12 Connector With Independent Cabling For Heating The wiring example provided below at Figure 1 is recommended for most installations, providing a separate cabling run of high quality cable for the Vaisala device heating current (if required). The pin connections for the 8-Pin M12 and wire colours are listed in Table 1 on page 7.
Installation Instructions for Innotech IG04 BACnet Gateway and Vaisala Transmitter / Sensor Wiring Using The 8-Pin M12 Connector With Split Cabling For Heating The wiring example provided below at Figure 2 is an alternative M12 connector wiring guide, providing a shared cabling run of suitable high capacity cable for the Vaisala device and heating accessory (if required). The pin connections for the 8-Pin M12 and wire colours are listed in Table 1 on page 7.
Installation Instructions for Innotech IG04 BACnet Gateway and Vaisala Transmitter / Sensor Vaisala Device 8-Pin M12 Connector Pin-Outs NOTENOTE Please take extreme care to ensure when installing and wiring that the wire colours and terminals correctly match as illustrated in Figure 1 or Figure 2, and described below in Table 1. Refer to the appropriate Vaisala technical documentation for more details at www.vaisala.com.
Installation Instructions for Innotech IG04 BACnet Gateway and Vaisala Transmitter / Sensor Wiring Using The Screw Terminal Connector With Independent Cabling For Heating The wiring example provided below at Figure 3 is recommended for most installations, providing a separate cabling run of high quality cable for the heating current (if required). The pin connections for the screw terminal connector and wire colours are listed in Table 2 on page 10.
Installation Instructions for Innotech IG04 BACnet Gateway and Vaisala Transmitter / Sensor Wiring Using The Screw Terminal Connector With Split Cabling For Heating The wiring example provided below at Figure 4 is an alternative screw terminal wiring guide, providing a shared cabling run of suitable high capacity cable for the Vaisala device and heating accessory (if required). The pin connections for the screw terminal connector and wire colours are listed in Table 2 on page 10.
Installation Instructions for Innotech IG04 BACnet Gateway and Vaisala Transmitter / Sensor Vaisala Device Screw Terminal Pin-Outs NOTENOTE Please take extreme care to ensure when installing and wiring that the wire colours and terminals correctly match as illustrated in Figure 1 or Figure 2, and described below in Table 2. Refer to the appropriate Vaisala technical documentation for more details at www.vaisala.com.
Installation Instructions for Innotech IG04 BACnet Gateway and Vaisala Transmitter / Sensor Accessing Embedded Web Server and FusionLIVE The Vaisala device and IG04 BACnet Gateway can be configured using the embedded web server and the FusionLIVE Java application on the IG04. However before you can access the embedded web server, your computer must be configured to be on the same network range as the IG04 BACnet Gateway. The default Ethernet settings for the IG04 BACnet Gateway are shown in Table 3 below.
Installation Instructions for Innotech IG04 BACnet Gateway and Vaisala Transmitter / Sensor Home Page of Embedded Web Server If your network settings are configured correctly, the home page of the embedded web server should be displayed. There are two different versions of the home page, configured to suit the two different models of supported Vaisala device. The embedded web server identifies which model of Vaisala device is connected before loading the appropriate home page.
Installation Instructions for Innotech IG04 BACnet Gateway and Vaisala Transmitter / Sensor Animated Graphics on the Home Page The home page provides animated graphical representations of live weather conditions when connected to a Vaisala WXT520 Weather Transmitter. The range of graphics and their meanings are illustrated in below in Figure 9.
Installation Instructions for Innotech IG04 BACnet Gateway and Vaisala Transmitter / Sensor When the button on the home page is clicked, the FusionLIVE window will be displayed. Refer to the illustration and table below for more detailed information. Actual live data in FusionLIVE will not be present until the connection between the IG04 BACnet Gateway and Vaisala device has been properly configured.
Installation Instructions for Innotech IG04 BACnet Gateway and Vaisala Transmitter / Sensor Configuring Vaisala Device with FusionLIVE When you have accessed the FusionLIVE Java application as described in the Accessing Embedded Server and FusionLIVE section, you can modify the configuration settings of the Vaisala device by clicking on the button from the FusionLIVE window. The Configure Vaisala Device Settings window will be displayed, as illustrated in Figure 11 below.
Installation Instructions for Innotech IG04 BACnet Gateway and Vaisala Transmitter / Sensor Configuring IG04 BACnet Gateway with FusionLIVE When you have accessed the FusionLIVE Java application by following the instructions described in the Accessing Embedded Server and FusionLIVE section, you can modify the configuration settings of the IG04 BACnet Gateway by clicking on the button from the FusionLIVE window.
Installation Instructions for Innotech IG04 BACnet Gateway and Vaisala Transmitter / Sensor BACnet Tab Under the BACnet tab you can configure or modify the following settings: • BACnet Instance number • BACnet Datalink protocol • BACnet MS/TP Settings Please note that the MS/TP settings can only be modified if the BACnet Datalink is selected as MSTP. Otherwise these settings cannot be modified and will be unaccessible.
Installation Instructions for Innotech IG04 BACnet Gateway and Vaisala Transmitter / Sensor Clock Tab Under the Clock tab you can configure or modify the following settings: • Current date and time – used for the Precipitation Reset setting • Daylight Savings time • Location – used to create Sunrise / Sunset data on the home page, along with day / night indication In order to adjust the Daylight Savings time, you must first enable it by turning the Operation to ON.
Installation Instructions for Innotech IG04 BACnet Gateway and Vaisala Transmitter / Sensor Configuring Sunrise and Sunset If you enable the Sunrise / Sunset feature of the IG04, you will need to enter the latitude and longitude coordinates to determine the sunrise and sunset for your particular location. This information can be obtained from http://www.findlatitudeandlongitude.com, using the map to find your location.
Installation Instructions for Innotech IG04 BACnet Gateway and Vaisala Transmitter / Sensor Ethernet Tab Under the Ethernet tab you can configure or modify the following settings: • Address type, IP address, Default Router, and Net Mask • HTTP Port Number • Net Comms Port number (Innotech Service Port number) • BACnet Port number As mentioned previously in the Accessing Embedded Server and FusionLIVE section, your computer MUST be on the same network range as the IG04 BACnet Gateway in order to access the
Installation Instructions for Innotech IG04 BACnet Gateway and Vaisala Transmitter / Sensor Services Tab Under the Service tab you can configure or modify the following settings: • Maintenance Mode – used for service by Innotech personnel. • Server IP Address – only used when Maintenance Mode is set to Server or Client. • Server Port – only used when Maintenance Mode is set to Server or Client.
Installation Instructions for Innotech IG04 BACnet Gateway and Vaisala Transmitter / Sensor Troubleshooting The most common issues when connecting to the IG04 BACnet Gateway's embedded web server and FusionLIVE are incorrect proxy settings or inappropriate security levels in Internet Explorer. If you are experiencing a problem that cannot be resolved, try some of the steps outlined below.
Installation Instructions for Innotech IG04 BACnet Gateway and Vaisala Transmitter / Sensor Cannot Launch FusionLIVE • When first launching FusionLIVE from the IG04 BACnet Gateway's embedded web server, you may encounter a window that asks you to install the Java Runtime Environment (JRE). Ensure to follow the prompts to download the JRE from the internet. If you do not have available internet access, you will not be able to continue until you have downloaded and installed the JRE onto the computer.
Innotech Support Innotech provides technical information on the Web to assist you with using its products. At www.innotech.com.au, you can find technical manuals, user instructions, and data sheets for all our products. For direct product support or product information, contact your local distributor, or an Innotech representative. You can contact us via email, fax, or postal mail: Website: Email: Fax: Mail: Edition 5.0 dated 11/11/2013 www.innotech.com.au sales@innotech.com.