Manual

ManualsBrandsInovonics ManualsCommunicationFA206DS

02154b.doc LIT-FA206DS-INSTALL hc:7-Aug-01

FA206DS

Frequency Agile

900MHz Transmitter

Passive InfraRed Motion Detector

Installation Instructions

02154B

Overview:

The FA206DS is an Inovonics transmitter incorporating the Detection Systems DS-775RF PIR. The unit

operates on a single 3.0V lithium battery (Duracell DL123A or equivalent).

Features:

Inovonics' reliable 900 Megahertz

Frequency Agile

radio link.

Motion Analyzer II™ signal processing.

3 interchangeable coverage patterns available for special applications (optional).

Internally pointable, field-replaceable mirrored optics.

5 mounting options permit flat wall, corner or hallway mounting, with swivel adjustments for aiming for

nominal coverage.

RFI Interference Immunity.

3.0V

Specifications:

Dimensions: 3.75"W x 5.75"L x 2 .50"D

Operating temperature: 32

F to 120

Voltage: 3 VDC

Battery: 1 - 3.0V lithium (Duracell DL123A or equivalent)

Note: Battery is always supervised

Broad coverage area: 50' x 50'

Barrier coverage area: 80' x 16'

Long Range coverage area: 120' x 10'

Mirror adjustment: +2

to -18

vertical, +10

to -10

horizontal

Sensitivity adjustment: Standard, Intermediate and High; jumper selectable

Test LED: Externally visible LED (during walk test mode)

Important Notes

These products are designed to be installed and maintained by professional security technicians.

Products, unless specifically noted, are intended for indoor use.

Manually test all products regularly.

Summary of content (8 pages)

PAGE 1
FA206DS Frequency Agile® 900MHz Transmitter Passive InfraRed Motion Detector Installation Instructions 02154B Overview: The FA206DS is an Inovonics transmitter incorporating the Detection Systems DS-775RF PIR. The unit operates on a single 3.0V lithium battery (Duracell DL123A or equivalent). Features: !" !" !" !" !" !" ® Inovonics' reliable 900 Megahertz Frequency Agile radio link. Motion Analyzer II™ signal processing. 3 interchangeable coverage patterns available for special applications (optional).
PAGE 2
!" Installation: Mounting Note: Recommended mounting height range is 6'6" to 8'6". Recommended mounting height is 7'6"(2.25m). General mounting advice: !" For best detection, locate the FA206DS so that intruders move across detection coverage patterns, rather than toward or away from the sensor. !" The mounting surface should be solid and vibration-free. !" Check areas for potential sources of false alarms. Remember that the sensor responds to quick changes in heat patterns within its coverage pattern.
PAGE 3
Mirror Assembly Adjustment: !" Set Vertical angle based on the following table. The table indicates setting for mirror type, mounting height and desired range. Vertical angle calibration markings are on the mirror. Slide the mirror forward or back until the angle hash marks are in line with the markers on each side of the frame. Mounting Height 6'6"(2m) 7'6"(2.3m) 8'6"(2.
PAGE 4
Sensitivity Mode Selection: The FA206DS has three sensitivity mode settings. Use the following information to determine the recommended setting. The sensitivity mode is selected by placement of a jumper on the 4-pin sensitivity header. STANDARD SENSITIVITY: This setting is recommended of Broad Coverage patterns. It tolerates extreme environment changes. It is not recommended for Long Range or Barrier mirror patterns. The FA206DS is shipped in Standard Sensitivity Mode.
PAGE 5
Programming the FA206DS: SET SCREW PROGRAMMING HEADER RESET BUTTON 3.0V SENSITIVITY SELECTOR Program contacts: Typical battery life: Battery type: Sleep after trip: TAMPER SWITCH WALK TEST LED N/C 2 years 3.0V lithium 180 seconds MIRROR OPTICS Programming the transmitter: 1. Remove the FA206DS cover. 2. Insert battery as shown. 3. Enter programming mode for the programming device, using the above recommendations as a guideline.
PAGE 6
Zone patterns for standard and optional mirror optics: Selection of appropriate mirror and mounting hardware lets the FA206DS be customized for any site. Following are descriptions of coverage patterns for the 3 mirrors available.
PAGE 7
Warranty & Disclaimer Inovonics Wireless Corporation ("Inovonics") warrants its products ("Product" or "Products") to conform to its own specifications and to be free of defects in materials and workmanship under normal use for a period of twenty-four (24) months from the date of manufacture. Within the warranty period Inovonics will repair or replace, at its option, all or any part of the warrantied product. Inovonics will not be responsible for dismantling and/or reinstallation charges.
PAGE 8
Additional products from Inovonics include: Frequency Agile® Receivers FA416 FA416D FA464 16-channel / 4-output 16-channel / 4-output with display 64-channel / 16-output Frequency Agile® Transmitters FA200(W) FA202 FA203(S/D) FA205(S/D) FA204 FA206 FA207 FA210(W) universal transmitter (optional widegap) smoke detector transmitter pendant transmitter (Single or Double Button) beltclip transmitter (Single or Double Button) pendant transmitter Sharpshooter PIR transmitter glassbreak detector transmitter red