Installation Guide

ManualsBrandsINOX ManualsDoor HardwareEC1217 Privacy Barn Door 3-1/2 in. Satin Chrome Finish Sliding Door Lock With Handle

Installation based on barn door application where doors are hung on the

OUTSIDE

of the room.

- Install Lock Inside the Jamb Wall behind the barn door

- Install Trim Plate on the Jamb Wall facing the opening

- Install Strike with an emergency release on the barn door

- Adjustable Strike for door thickness from 1-3/8” to 2-1/4”.

- Thick Door Kits Available.

Wall Thickness:

LOCK BOLT NO. BACKSET WALL THICKNESS TYPICAL WALL STUDS

BD4214 2-1/4” 4-1/2”+ 2 x 4

BD4312 3-1/2” 6-1/2”+ 2 x 6

Items No. Parts Description

Function

Privacy

Trim Parts

Lock

Strike

Others

Face Fixing Trim with spindle

M4 x 50 Slotted Head Screws

Barn Door Lock

M4 x 40 Wood Screws

Lock Bracket

Dust Proof Strike

Washer

Sleeve

Hollow Screw

Decorative Cap

Emergency Key

Door Prep Template

Installation Instruction

1 EA

2 EA

1 EA

2 EA

1 EA

2 EA

1 EA

BD4000 Series Privacy Barn Door Lock Set Parts List:

(With Face Fixing Trim Plate)

INSTALLATION INSTRUCTIONS

BD4000 Privacy Barn Door Lock

( PM-IS1301-V161001 )

Wall Conditions and Tools Suggestion

Most of the drywall will have corner bead in steel or vinyl; it’s strongly recommended to use Hole Saw to cut the holes for installing locks and

trim plates. Hole Saw for steel will also help cutting through any screws inside drywall or wood stud to make the installation job run faster.

Recommend to Use:

Stud Finder

Hole Saw

2-1/8”

1-1/4”

1”

Level

T-Square

1/8” Drill Bit

DO NOT USE:

Spade Bit

1/4" Drill Bit

Engineered Beautifully™

Summary of content (4 pages)

PAGE 1
BD4000 Privacy Barn Door Lock INSTALLATION INSTRUCTIONS Engineered Beautifully™ ( PM-IS1301-V161001 ) Installation based on barn door application where doors are hung on the OUTSIDE of the room. - Install Lock Inside the Jamb Wall behind the barn door Install Trim Plate on the Jamb Wall facing the opening Install Strike with an emergency release on the barn door Adjustable Strike for door thickness from 1-3/8” to 2-1/4”. Thick Door Kits Available. Wall Thickness: LOCK BOLT NO.
PAGE 2
Step 1. Wall and Door Preparation B. Opening with Casing greater than 1-5/8” A. Drywall Opening Choose center hole location based on your aesthetic preference, so long as it is at least 1" from the edge. For drywall opening with 1/2" drywall (gypsum board), minimum 2" door overlap is needed to install BD4000 privacy lock. The lock bore center must be at least 1" from wall edge; align strike with lock.
PAGE 3
Step 2. Prep Trim Bore – On the Jamb (CONT.) TIP: Before drilling, cover area around the bore hole with masking tape to prevent the drywall from chipping or cracking. 2.3) With a 2-1/8” hole saw, drill on Jamb side in accordance with following steps. Without Casing: a. Drill through drywall approx. 1/2” to locate first wood stud. b. Continue drilling 1” into the stud. IMPORTANT! Do not exceed depth of wood stud when drilling. Minimum 1/4” or thicker wood backing is required to support the lock.
PAGE 4
Step 4. Installation of the Lock (CONT.) 4.4) Ensure spindle hub is at center of trim bore. Use spindle or screwdriver to test bolt retraction; if not smooth, troubleshoot as follows: - Check 2-1/8" trim bore dimensions Ensure hole is free of debris Make sure 1" lock bore is perpendicular to trim bore Check lock by removing it from bore and throwing the bolt. Adjust wall prep as needed 4.5) Fasten the two wood screws inside the trim bore hole through lock body and into wood stud. Step 5.