USER GUIDE Desktop/Dual Desktop Monitor Mount NS-PGSMM6120-C/NS-PGSMM6220-C Before using your new product, please read these instructions to prevent any damage.
NS-PGSMM6120-C/NS-PGSMM6220-C Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Desktop/Dual Desktop Monitor Mount Features • • • Gas spring function offers tilt, swivel, and height adjustments Cable management helps keep your desk clean Clamp base or grommet base options provided Compatibility Single-Arm Mount Supports most monitors that are: • 10-30 in. • 4.4-19.8 lbs. (2-9 kg) • VESA mount pattern: 75 × 75 or 100 × 100 Dual-Arm Mount Supports most monitors that are: • 10-30 in. • 4.4-19.8 lbs. (2-9 kg) • VESA mount pattern: 75 × 75 or 100 × 100 www.insigniaproducts.
NS-PGSMM6120-C/NS-PGSMM6220-C Package contents Note: You will not use all parts or hardware to set up your monitor mount. Parts Single-Arm Mount (NS-PGSMM6120-C) 4 Item 1 Monitor arm 2 Clamp base support 3 Grommet pad 4 Cable guide 5 Clamp pad(s) 6 Clamp 7 Grommet base support 8 Bolt 9 Pressure plate pad(s) 10 Pressure plate 11 Knob 12 Cable cover www.insigniaproducts.
Desktop/Dual Desktop Monitor Mount Hardware Single-Arm Mount (NS-PGSMM6120-C) Item Dual-Arm Mount (NS-PGSMM6220-C) M4 × 12 mm screws (4 pcs.) A M4 × 12 mm screws (8 pcs.) M5 × 12 mm screws (4 pcs.) B M5 × 12 mm screws (8 pcs.) M6 × 12 mm screws (3 pcs.) C M6 × 12 mm screws (3 pcs.) M6 × 10 mm screws (2 pcs.) D M6 × 14 mm screws (2 pcs.) Washers (8 pcs.) F Washers (16 pcs.) 4 mm hex wrench G 4 mm hex wrench 5 mm hex wrench H 5 mm hex wrench www.insigniaproducts.
NS-PGSMM6120-C/NS-PGSMM6220-C Installing your monitor mount Note: Make sure that your monitor is compatible with your mount before installation. See "Compatibility" on page 3. Step 1 - Selecting a mounting option • • Option A: Attaching the mount to the edge of your desk. See page 6. Option B: Attaching the monitor mount to a desk grommet hole. See page 8.
Desktop/Dual Desktop Monitor Mount 3 Remove the backing from the clamp pad(s) (5) then press onto the clamp (6). Dual-Arm Mount Single-Arm Mount 5 5 6 6 4 Use two screws (D) and a hex wrench (G) to attach the clamp (6) to the clamp base support (2). Select the two holes that will hold the mount to your desk securely. The mount supports desks that are 0.8-4.7 in. (20-120 mm) thick. Dual-Arm Mount Single-Arm Mount D G D 6 G 5 Continue to "Step 3 - Attaching the monitor to the mount" on page 9.
NS-PGSMM6120-C/NS-PGSMM6220-C Step 2 - Option B: Assembling the grommet assembly Select the position on the desk where you want your monitor mount installed. Make sure that there is enough room for the monitor. The desk should between 1.0-4.7 in. (25-120 mm) thick and strong enough to bear the weight of your monitor. The grommet hole should be 0.3-2.8 in. (8.5-70 mm) in diameter. 1 Insert the bolt (8) through the square hole on the grommet base support (7).
Desktop/Dual Desktop Monitor Mount 4 Remove the backing from the pressure plate pad(s) (9), then press it onto the pressure plate (10). Dual-Arm Mount Single-Arm Mount 9 9 10 10 5 Continue to "Step 3 - Attaching the monitor to the mount" on page 9. Step 3 - Attaching the monitor to the mount 1 Lay your monitor face-down on a soft, flat surface. 2 Center the monitor plate on the back of your monitor and align the mounting holes.
NS-PGSMM6120-C/NS-PGSMM6220-C Step 4 - Option A: Attaching to the edge of your desk 1 Align the clamp with your desk, then tighten the knob until the mount is secure. Note: If the clamp will not tighten fully, repeat step 4 to move the clamp to a higher position on the base support. Dual-Arm Mount Single-Arm Mount Desk Desk Step 4 - Option B: Attaching to a desk grommet 1 Thread the bolt (8) through the grommet hole in your desk.
Desktop/Dual Desktop Monitor Mount Step 5 - Adjusting the mount tension Note: If you have a dual-arm monitor (NS-PGSMM6220-C), repeat these steps for both arms. Single-arm monitor graphics shown. Vertical tension • If the mount arm is rising up, use a hex wrench (H) to turn the screw clockwise. OR If the mount arm is sinking down, use a hex wrench (H) to turn the screw counterclockwise. H Tilt tension • If your monitor is falling forward, use a hex wrench (H) to turn the screw clockwise.
NS-PGSMM6120-C/NS-PGSMM6220-C Arm tension • If it is hard to move your mount arm, use a hex wrench (G) to turn the screw counterclockwise. OR If your mount arm moves too easily, use a hex wrench (G) to turn the screw clockwise.. G Mount head tension • If it is hard to move the entire mount head assembly, use a hex wrench (G) to turn the screw counterclockwise. OR If the entire head mount assembly is falling forward, use a hex wrench (G) to turn the screw clockwise.. G 12 www.insigniaproducts.
Desktop/Dual Desktop Monitor Mount Step 6 - Managing cables 1 Connect your cables to your monitor, then raise it to its highest postion. 2 Guide the cables under your mount arm, then clip on the cable cover (4). 3 If you used the mounting clamp assembly (Step 2, Option A), clip the cable guide (4) to the clamp base support (2), then secure your cables in its clips. 4 Make sure that the mount arm is able to move freely without pulling on the cables. 12 4 2 www.insigniaproducts.
NS-PGSMM6120-C/NS-PGSMM6220-C Specifications Item Single-Arm Mount (NS-PGSMM6120-C) Dual-Arm Mount (NS-PGSMM6220-C) Monitor size 10 to 30 inch monitor 10 to 30 inch monitors Max load capacity 4.4-19.8 lbs. (2-9 kg) 4.4-19.8 lbs. (2-9 kg) for each monitor plate Tilt angle -85° ~ 15° -85° ~ 15° Integrated cable management Yes Yes Copyright Insignia is a trademark of Best Buy and its affiliated companies. Distributed by Best Buy Purchasing, LLC © 2016 Best Buy. All rights reserved.
Desktop/Dual Desktop Monitor Mount ONE-YEAR LIMITED WARRANTY - INSIGNIA Definitions: The Distributor* of Insignia branded products warrants to you, the original purchaser of this new Insignia-branded product (“Product”), that the Product shall be free of defects in the original manufacturer of the material or workmanship for a period of one (1) year from the date of your purchase of the Product (“Warranty Period”).
NS-PGSMM6120-C/NS-PGSMM6220-C • Commercial purposes/use, including but not limited to use in a place of business or in communal areas of a multiple dwelling condominium or apartment complex, or otherwise used in a place of other than a private home. • Modification of any part of the Product, including the antenna • Display panel damaged by static (non-moving) images applied for lengthy periods (burn-in).
www.insigniaproducts.com 1-877-467-4289 (U.S. and Canada) or 01-800-926-3000 (Mexico) INSIGNIA is a trademark of Best Buy and its affiliated companies. Distributed by Best Buy Purchasing, LLC ©2016 Best Buy. All rights reserved. Made in China.
