Quick Start Guide

USING YOUR HEADPHONES
Turning on and pairing your headphones
1 Connect the AC power adapter to the 5V/500mA (DC in) jack. The Power/Pairing indicator on the docking
station blinks (blue).
2 Press and hold (for more than two seconds) the Power button on the right earpiece to turn on the
headphones. The Power/Pairing indicator on the headphone lights (blue).
-OR-
If the headphones are on the docking station, they will be powered on when you take them o the
station.
3 When the Power/Pairing indicator on the headphones and the Power/Pairing indicator on the docking
station turns solid blue, an active link is established between the headphones and the docking station.
Your headphones are ready to use.
4 To change the audio input to match the device connected to the docking station:
• Press the Input Source button on the docking station, or
• Press and hold the Input Source button on the headphones for two seconds
The selected source indicator lights white.
Listening to your headphones
1 Turn on the headphones. Make sure that your docking station and headphones are wirelessly paired.
2 Set the headphone volume level to the minimum.
3 Put your headphones on your head. Adjust the t until you feel comfortable.
4 Turn on your audio source and begin playback. Depending on the audio source, you may need to turn up
the volume on the audio source.
5 Adjust the headphone volume to your normal listening level.
Caution: Continuous use at high volume may permanently damage your hearing.
Notes:
• If the system is connected to a TV, you may want to turn o the TV speakers. Refer to your TV manual.
• If the docking station does not have audio input for more than 15 minutes, the headphones will power o
automatically.
• If the headphones are unpaired from the docking station for more than 15 minutes, the headphones will power o
automatically.
• If the docking station is unpaired for more than ve minutes, the docking station LED will turn o.
Turning o your headphones
Press and hold (more than two seconds) the (power) button on your headphones.
Note: Turn the headphones o when not in use to conserve the battery.
Turning o your docking station
Disconnect the AC power adapter to turn o the docking station.
TROUBLESHOOTING
No power
• Make sure that the headphones’ battery is charged.
• Make sure that your headphones are turned on.
No sound or low volume
• Shorten the distance between the docking station and your source device.
• Make sure that your source device is turned on.
• Turn up the volume on your headphones and source device. Make sure that your source device is not
muted.
Power/pairing indicator
Power button
Cannot pair the headphones
• Shorten the distance between the docking station and your headphones.
• Make sure that the docking station is in pairing mode.
• Turn on the docking station, then place the headphones onto the station. They will enter autopairing
mode (this may take 2-20 seconds).
Tip: If the power indicators on the headphones and docking station continue to blink after 20 seconds, they are
no longer paired to each other. If this happens, follow these steps:
1 Make sure that the headphones and docking station are within range of each other (ideally in the same room).
2 Turn o the headphones and the docking station.
3 Turn on both the headphones and the docking station. The lights will initially blink, then turns solid blue when
connected.
SPECIFICATIONS
• Headphone dimensions (H × W × D): 7.5 × 3.0 × 6.7 in. (191.2 × 76.8 × 171.2 mm)
• Docking station dimensions (H × W × D): 8.5 × 3.8 × 4.7 in. (214.7 × 96.5 × 119.9 mm)
• Input: AC 100-240 V~ 50/60 Hz 0.3 A
• Output: 5 V, 500 mA
• Battery Life: Up to 10 hours
• Range: 33 feet (10 m)
• Charging time: 2 hours
• Audio resolution: 48 Khz @ 16 bits
• Audio Source Port: Analog: RCA *1
Digital: Optical *1 PCM (does not support DTS and Dolby Audio)
LEGAL NOTICES
FCC and IC Information:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including interference that may cause undesired operation.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Warning: Changes or modications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
This equipment complies with Industry Canada radiation exposure limits set forth for an uncontrolled environment.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
ONEYEAR LIMITED WARRANTY
Visit www.insigniaproducts.com for details.
CONTACT INSIGNIA:
For customer service, call 1-877-467-4289 (U.S. and Canada)
www.insigniaproducts.com
INSIGNIA is a trademark of Best Buy and its aliated companies.
Distributed by Best Buy Purchasing, LLC
7601 Penn Ave South, Richeld, MN 55423 U.S.A.
©2022 Best Buy. All rights reserved.
- PICK ONE -
Television
DIGITAL
OPTICAL
IN
AUDIO
IN
AUDIO
OUT
DIGITAL
OPTICAL
IN
AUDIO
IN
AUDIO
OUT
OPTICAL audio cable
DIGITAL
OPTICAL
IN
AUDIO
IN
AUDIO
OUT
DIGITAL
OPTICAL
IN
AUDIO
IN
AUDIO
OUT
Docking station (back)
Home theater
system
RCA cable
Television
- OR -
- OR -
Home theater
system
Television
IN
DIGITAL
OPTICAL
IN
AUDIO
IN
AUDIO
OUT
DIGITAL
OPTICAL
IN
AUDIO
IN
AUDIO
OUT
Note: This is an
optional connection.
RCA cable
(not included)
RCA cable
(included)
DIGITAL
OPTICAL
IN
AUDIO
IN
AUDIO
OUT
DIGITAL
OPTICAL
IN
AUDIO
IN
AUDIO
OUT
Docking station (back) TelevisionHome theater system
Computer
Tablet
Smartphone
RCA cable 3.5 mm-RCA adapter cable
JACK TYPE
(on source device)
OPTICAL cable
RCA audio cable
(included)
3.5 mm adapter
(included)
AC power adapter
(included)
CABLE
Use an optical cable from the optical output of your source
device to the DIGITAL OPTICAL IN jack of the docking station.
Use the included RCA cables to connect from the RCA audio
OUTPUT ports of your source device to the AUDIO IN jacks of
the docking station.
Use the included 3.5 mm adapter and RCA cable to connect
to a source device with a 3.5 mm connection.
Use the AC power adapter to charge the docking station and
headphones.
WHEN TO USE
CONNECTING THE HEADPHONES
Locate the AUDIO OUT port on your audio source device, such as a TV, stereo system, home theater,
smartphone, computer, or tablet. Choose the connection option below that ts your audio source
device.
TIPS:
TV speakers may continue to produce sound or may be muted, depending on the settings on your TV. Refer to your
TV’s user guide for more information.
To get sound from all devices connected to your TV, you will need to connect to an audio out port on the TV. If you
connect to another source device, you will only get sound from that device.
OPTICAL connection
1 Connect one end of an optical cable to the DIGITAL OPTICAL IN jack on the docking station.
2 Connect the other end into the OPTICAL OUT jack of your TV or any other audio source device with
optical audio output.
TIP: To get optical audio output from your TV, you must change your TV's audio format to PCM. Refer to your TV’s
user guide for more information.
Multiple connections (Optional)
If your audio source device (a TV in the example
shown) only has one audio output, but you want to
connect it to both the docking station and a stereo
system or home theater, do this.
1 Connect one end of the RCA cable (included) to
the red and white AUDIO IN ports on the
docking station.
2 Connect the other end to the red and white
AUDIO OUT ports on your audio source device.
Note: Use the 3.5 mm-to-RCA cable adapter to
connect to a headphone jack, if necessary.
3 Connect one end of an RCA cable (not included)
to the red and white AUDIO OUT ports on the
docking station.
4 Connect the other end to the red and white
AUDIO IN ports on your stereo system or home
theater. The audio should now play through
your home theater speakers.
RCA connection
1 Connect one end of the RCA cable to the red and white AUDIO IN ports on the docking station.
2 Connect the other end into the red and white AUDIO OUT ports on your audio source device.
3.5 mm connection
1 Connect one end of the RCA cable to the red and white AUDIO IN ports on the docking station.
2 Connect the other end into the red and white connectors on the 3.5 mm-RCA adapter cable.
3 Connect the 3.5 mm audio cable into the 3.5 mm headphone or AUDIO OUT jack on your audio
source device.
Power/Pairing indicator
V6 ENGLISH 22-0066