ASSEMBLY GUIDE 58" TV Gaming Stand NS-HF2007 Before using your new product, please read these instructions to prevent any damage.
Contents IMPORTANT SAFEGUARDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Features • • • • • • • Supports 65 in. (165 cm) TVs up to 60 lbs. (27.
58" TV Gaming Stand Maximum weights 30 lbs. (13.6 kg) TV size: 61" 60 lbs. (155 cm) (27.3 kg) 5 lbs. (6.8 kg) 20 lbs. (9.1 kg) 20 lbs. (9.1 kg) 60 lbs. (27.3 kg) WARNING: You can use most flat panel televisions weighing 60 lbs. (27.3 kg) or less. Using televisions or weights heavier than the maximums can result in instability that can cause tip-overs resulting in death or serious injury. 4 www.insigniaproducts.
Package contents Parts D Long lower shelf (1) A Base (1) B Left divider panel (1) C Right divider panel (1) G Top (1) F Front edge (1) E Upper shelf (1) H Lower support (1) I Left side support (1) J Right side support (1) O Short upper shelf (1) N Door (1) K Left side (1) P Left drawer side (1) Q Right drawer side (1) L Right side (1) R Drawer back (1) M Lower back panel (1) S Drawer bottom (1) T Drawer support (1) Y Small divider panel(1) U Drawer front (1) V Upper back panel (1) www.
58" TV Gaming Stand Hardware LABEL STAND PART 3 × 12 mm screw AA QTY. LABEL STAND PART QTY. 12 MM Shelf support 4 1 set NN 3.5 × 12 mm screw 4 42 OO 40 PP 44 QQ 4.
Assembly instructions STEP 1: You need: CL DR AA 3 × 12 mm screw (6) B Left divider panel (1) Phillips screwdriver CR DL BB Left and right rail assembly (2) C Right divider panel (1) 1 Separate the CL and CR parts of the rail assembly (BB) from the DL and DR parts and set the DL and DR parts aside for use in another step. 2 Insert three 3 × 12 mm screws (AA) into the correct holes on the CL and CR parts of the rail assembly (BB).
58" TV Gaming Stand 6 Tighten the screws with a Phillips screwdriver. AA AA AA CR BB 8 www.insigniaproducts.
STEP 2: You need: CC Cam screw (4) B Left divider panel (1) Phillips screwdriver C Right divider panel (1) 1 Insert two cam screws (CC) into the holes on the left divider panel (B), then tighten the screws with a Phillips screwdriver. CC CC 2 Insert two cam screws (CC) into the holes on the right divider panel (C), then tighten the screws with a Phillips screwdriver. CC CC www.insigniaproducts.
58" TV Gaming Stand STEP 3: You need: EE Dowel (4) D Long lower shelf (1) • Insert four dowels (EE) into the short edges of the long lower shelf (D). EE EE EE EE 10 www.insigniaproducts.
STEP 4: You need: Phillips screwdriver D Long lower shelf (1) B Left divider panel (1) DD Small cam lock (4) C Right divider panel (1) Using cam locks When you insert a cam lock, position the open end of the lock toward the cam screw, then insert the cam screw into the cam lock opening. 1 Insert four cam locks (DD) into the long lower shelf (D).
58" TV Gaming Stand STEP 5: You need: EE Dowel (8) • Insert eight dowels (EE) into the edges of the divider panels (B and C). Make sure that you use the inside hole of each pair of holes. EE EE EE EE EE EE EE EE 12 www.insigniaproducts.
STEP 6: You need: Phillips screwdriver GG Magnetic door latch (1) FF 3 × 15 mm screw (2) E Upper shelf (1) • Align the magnetic door latch (GG) with the holes on the upper shelf (E), then secure the latch with two 3 × 15 mm screws (FF) using a Phillips screwdriver. Make sure that you attach the latch to the side of the shelf that has cross bars. FF GG FF www.insigniaproducts.
58" TV Gaming Stand STEP 7: You need: CC cam screw (4) Phillips screwdriver E Upper shelf (1) • Insert four cam screws (CC) into the outer holes on the upper shelf (E), then tighten the screws using a Phillips screwdriver. CC CC CC CC 14 www.insigniaproducts.
STEP 8: You need: EE Dowel (2) Y Small divider panel (1) HH 4 × 50 mm screw (2) Phillips screwdriver E Upper shelf (1) 1 Insert two dowels (EE) into the long edge of the small divider panel (Y). 2 Insert two 4 × 50 mm screws (HH) through the upper shelf (E) and into the small divider panel (Y), then tighten the screws with a Phillips screwdriver. EE HH HH www.insigniaproducts.
58" TV Gaming Stand STEP 9: You need: Phillips screwdriver DD Cam lock (4) Using cam locks When you insert a cam lock, position the open end of the lock toward the cam screw, then insert the cam screw into the cam lock opening. 1 Insert the dowels and cam screws on the upper shelf (E) into the dowel cam lock holes on the left and right divider panels (B and C), then tighten the screws with a Phillips screwdriver.
STEP 10: You need: EE Dowel (4) A Base (1) • Insert four dowels (EE) into the edge of the base (A). Make sure that you use the holes that don’t have holes above them. EE EE EE EE www.insigniaproducts.
58" TV Gaming Stand STEP 11: You need: CC Cam screw (4) Phillips screwdriver F Front edge (1) 1 Insert four cam screws (CC) into the edge of the front edge (F). Make sure that you use the outer screw hole in each pair of holes. 2 Tighten the screws with a Phillips screwdriver. CC CC CC CC 18 www.insigniaproducts.
STEP 12: You need: Phillips screwdriver DD Cam lock (4) F Front edge (1) A Base (1) When you insert a cam lock, position the open end of the lock toward the cam screw, then insert the cam screw into the cam lock opening. 1 Insert four cam locks (DD) into the holes on the base (A). 2 Insert the cam screws and dowels on the front edge (F) into the cam locks and dowel holes on the base (A), then tighten the cam locks with a Phillips screwdriver. DD DD DD DD www.insigniaproducts.
58" TV Gaming Stand STEP 13: You need: CC Cam screw (4) EE Dowel (4) Phillips screwdriver 1 Insert four dowels (EE) into the middle holes on the base (A). Make sure that you use the inner hole on each pair of holes. 2 Insert four cam screws (CC) into holes on the base. Make sure that you use the outer hole on each pair of holes. 3 Tighten the screws with a Phillips screwdriver. CC EE EE EE CC EE CC EE CC CC 20 www.insigniaproducts.
STEP 14: You need: Phillips screwdriver DD Cam lock (4) H Lower support (1) When you insert a cam lock, position the open end of the lock toward the cam screw, then insert the cam screw into the cam lock opening. 1 Insert four cam locks (DD) into lower support (H). 2 Insert the cam screws in the base (A) into the cam locks, then tighten the cam locks with a Phillips screwdriver. DD DD DD DD www.insigniaproducts.
58" TV Gaming Stand STEP 15: You need: HH 4 × 50 mm screw (4) Phillips screwdriver 1 Insert four 4 × 50 mm screws (HH) through the base (A) and into the holes on the bottom edges of the left and right divider panels. 2 Tighten the screws with a Phillips screwdriver. HH HH HH HH 22 www.insigniaproducts.
STEP 16: You need: EE Dowel (12) 1 Insert four dowels (EE) into the base (A). 2 Insert four dowels (EE) into the front edge (F). 3 Insert four dowels (EE) into the left and right divider panels (A and B). EE EE EE EE EE EE EE EE EE www.insigniaproducts.
58" TV Gaming Stand STEP 17: You need: CC Cam screw (6) I Left side support (1) EE Dowel (4) Phillips screwdriver J Right side support (1) 1 Insert three cam screws (CC) and two dowels (EE) into the left side support (I) and three cam screws and two dowels into the right side support (J). 2 Tighten the screws with a Phillips screwdriver. CC EE 24 www.insigniaproducts.
STEP 18: You need: Phillips screwdriver DD Cam lock (6) I Left side support (1) J Right side support (1) K left side (1) L Right side (1) When you insert a cam lock, position the open end of the lock toward the cam screw, then insert the cam screw into the cam lock opening. 1 Insert three cam locks (DD) into the left side (K) and three cam locks into the right side (L).
58" TV Gaming Stand STEP 19: You need: CC Cam screw (12) Phillips screwdriver • Insert six cam screws (CC) into the left side (K) and six cam screws into the right side (L), then tighten the screws with a Phillips screwdriver. CC CC CC CC CC CC CC CC 26 CC www.insigniaproducts.
STEP 20: You need: Phillips screwdriver DD Cam lock (12) Using cam locks When you insert a cam lock, position the open end of the lock toward the cam screw, then insert the cam screw into the cam lock opening. r 1 2 3 4 5 Insert one cam lock (DD) into each corner of the bottom of the upper shelf (E). Insert one cam lock into each corner of the bottom of the base (A). Insert two cam locks into the bottom of the left and right sides of the lower shelf (H).
58" TV Gaming Stand STEP 21: You need: V Upper back panel (1) M Lower back panel (1) • Slide the lower back panel (M) into the grooves on the left and right sides (K and L) then slide the upper back panel (V). 28 www.insigniaproducts.
STEP 22: You need: EE Dowel (6) • Insert two dowels (EE) into the top edges of the left side (K), the right side (K), and the small divider (Y). Make sure that you use the inside hole in each pair of holes. EE EE EE EE EE EE www.insigniaproducts.
58" TV Gaming Stand STEP 23: You need: CC Cam screw (6) Phillips screwdriver G Top (1) 1 Insert one cam screw (CC) into each corner and the middle of the top (G). Make sure that you use the outside hole of each pair of holes. 2 Tighten all screws with a Phillips screwdriver. CC CC CC CC CC CC 30 www.insigniaproducts.
STEP 24: You need: Phillips screwdriver DD Cam lock (6) When you insert a cam lock, position the open end of the lock toward the cam screw, then insert the cam screw into the cam lock opening. 1 Insert two cam locks (DD) into the inside top edges of the left side (K), the right side (L), and the left top side of the small divider (Y). 2 Lay the top (G) onto the left and right sides. Make sure that the cam screws fit into the cam locks, 3 Tighten all cam locks with a Phillips screwdriver.
58" TV Gaming Stand STEP 25: You need: VV Cam lock cover (14) • Snap cam lock covers (W) over the exposed cam locks on the left and right sides, the small divider (panel), and the left and right divider panels. VV 32 www.insigniaproducts.
STEP 26: You need: Phillips screwdriver SS 3.5 × 16 mm screw (12) RR Back support bracket (12) • Insert twelve back brackets (RR) into the edges of the back panels, then secure each bracket with a 3.5 × 16 mm screw (SS). RR www.insigniaproducts.
58" TV Gaming Stand STEP 27: You need: Phillips screwdriver II 3 × 16 mm screw (6) TT Cable wrap (2) 1 Insert six 3 × 16 mm screw (II) along the outer edges of the lower back (M), then tighten the screws with a Phillips screwdriver. 2 Align two cable wraps (TT) with the holes in the middle of the lower back, then secure each wrap with a 3 × 16 mm screw (II) using a Phillips screwdriver. TT II 34 www.insigniaproducts.
STEP 28: You need: Phillips screwdriver JJ Handle (1) 1 Remove the screws from the handle (JJ). 2 Align the handle with the holes on the outside of the door (N), then insert the screws through the inside of the door and into the handle. 3 Tighten the screws with a Phillips screwdriver. JJ www.insigniaproducts.
58" TV Gaming Stand STEP 29: You need: Phillips screwdriver XX 3 × 12 mm screw (4) KK Lower hinge pin (1) LL Upper hinge pin (1) 1 Insert the lower hinge pin (KK) into the pin hole on the left bottom of cabinet. 2 Insert the upper hinge pin (LL) into the pin hole on the left top of cabinet. 3 With the handle facing out, slide the door (N) onto the hinge pins that the screw holes on the door align with the holes in the hinge pins.
STEP 30: After the door is installed, you might need to adjust the door so that it fits snuggly into the cabinet. You need: Phillips screwdriver • Loosen the hinge pin screws, slightly slide the door forward or back, then tighten the screws. www.insigniaproducts.
58" TV Gaming Stand STEP 31: You need: O Short upper shelf (1) MM shelf support (4) 1 Insert the four shelf supports (MM) inside the cabinet. Make sure that all the supports are on the same level. 2 Tilt the short upper shelf (O), then slide the shelf above the shelf supports and into the cabinet. 3 Lower the shelf onto the supports. MM 38 www.insigniaproducts.
STEP 32: You need: P Left drawer side (1) Q Right drawer side (1) OO Drawer support (2) NN 3.5 × 12 mm screw (4) Phillips screwdriver 1 Align a drawer support (OO) with the holes on the inside of the left drawer side (P), then insert two 3.5 × 12 mm screws (NN) through the outside of the drawer and into the support. 2 Tighten the screws with a Phillips screwdriver. 3 Align a drawer support (OO) with the holes on the inside of the right drawer side (Q), then insert two 3.
58" TV Gaming Stand STEP 33: You need: PP 4 × 38 mm screw (4) Phillips screwdriver R Drawer back (1) 1 With the grooves in the drawer back (R) and the left and right drawer sides (P and Q) facing inward, insert two 4 × 38 mm screws (PP) through the left and right drawer sides and into the drawer back. 2 Tighten the screws with a Phillips screwdriver. 40 www.insigniaproducts.
STEP 34: S Drawer bottom (1) • With the drawer back facing down, slide the drawer bottom (S) into the grooves on the drawer sides and back. www.insigniaproducts.
58" TV Gaming Stand STEP 35: You need: T Drawer support (1) PP 4 × 38 mm screw (2) Phillips screwdriver 1 Insert two 4 × 38 mm screws (PP) through the holes on the back of the drawer and into the holes in the drawer support (T). 2 Tighten the screws with a Phillips screwdriver. 42 www.insigniaproducts.
STEP 36: You need: CC Cam screw (2) Phillips screwdriver U Drawer front (1) • With the groove in the drawer front (U) facing up, insert two cam screws (CC) into the drawer front, then tighten the screws with a Phillips screwdriver. www.insigniaproducts.
58" TV Gaming Stand STEP 37: You need: Phillips screwdriver WW Cam lock (2) When you insert a cam lock, position the open end of the lock toward the cam screw, then insert the cam screw into the cam lock opening. 1 Insert the two cam screws on the drawer front (U) into the drawer support. 2 Insert two cam locks (WW) into the two holes on the drawer support, then tighten the locks with a Phillips screwdriver. WW 44 www.insigniaproducts.
STEP 38: You need: Phillips screwdriver QQ 4.5 × 14 mm screw (4) 1 Align the sides of the drawer so the holes in the brackets align with the holes on the drawer front. 2 Insert two 4.5 × 14 mm screws (QQ) through each bracket and into the drawer front. 3 Tighten the screws with a Phillips screwdriver. QQ QQ www.insigniaproducts.
58" TV Gaming Stand STEP 39: You need: JJ Handle (1) Phillips screwdriver 1 Remove the screws from the handle (JJ). 2 Align the handle with the holes on the outside of the drawer front, then insert the screws through the back of the drawer front and into the handle. 3 Tighten the screws with a Phillips screwdriver. JJ 46 www.insigniaproducts.
STEP 40: You need: CL DR AA 3 × 12 mm screw (6) DL CR Phillips screwdriver BB Left and right rail assembly (2) 1 Insert three 3 × 12 mm screws (AA) into the holes on the DL and DR parts of the rail assembly (BB). 2 Align the screws in the DL and DR parts of the rail assembly with the holes on the outside of the left and right drawer sides. 3 Tighten the screws with a Phillips screwdriver. DR AA DL AA www.insigniaproducts.
58" TV Gaming Stand STEP 41: 1 Align the rail assemblies on the drawer with the rails inside cabinet, then slightly lift the drawer up so that the wheels fit into the slots on the rail assemblies. 2 Slide the drawer into the cabinet. 48 www.insigniaproducts.
STEP 42: You need: Phillips screwdriver UU Anti-tip bracket with plastic strap (2) 1 Insert one screw through one hole on each bracket and into the left and right holes on the top of the back. Tighten the screws with a Phillips screwdriver. 2 Insert two screws through the two holes on each bracket and into the wall stud. Tighten the screws with a Phillips screwdriver. 3 Pull the plastic strap on each bracket to secure your TV stand to the wall. Tighten the screws with a Phillips screwdriver.
58" TV Gaming Stand Maintaining your TV stand Your TV stand is designed for year-round use with only minimal cleaning and maintenance. • Use a soft, clean, cloth that won’t scratch the surface when dusting. • Use of furniture polish is not necessary. Should you choose to use polish, test first in an inconspicuous area. • Using solvents of any kind on your furniture may damage the finish. • Never use water to clean your furniture as it may cause damage to the finish.
ONE-YEAR LIMITED WARRANTY Definitions: The Distributor* of Insignia branded products warrants to you, the original purchaser of this new Insignia-branded product (“Product”), that the Product shall be free of defects in the original manufacturer of the material or workmanship for a period of one (1) year from the date of your purchase of the Product (“Warranty Period”).
www.insigniaproducts.com 1-877-467-4289 (U.S. and Canada) INSIGNIA is a trademark of Best Buy and its affiliated companies. Distributed by Best Buy Purchasing, LLC 7601 Penn Ave South, Richfield, MN 55423 U.S.A. ©2022 Best Buy. All rights reserved.
