ASSEMBLY GUIDE 3-in-1 TV Stand NS-HFTVS3N175 Before using your new product, please read these instructions to prevent any damage.
Contents IMPORTANT SAFEGUARDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
-in-1 TV Stand IMPORTANT SAFEGUARDS WARNING Some steps are more easily handled with two adults. CAUTION The top surface of this stand is designed for use with a product weighing no more than 100 lbs. (45.4 kg) and having a width that permits it to sit evenly on the stand with no more than a one-inch overhang on each side of the shelf.
Features • • • • • • 3-in-1 display system lets you tilt (5° up/11° down) or swivel (45° left/right) your TV to find the best view Sturdy mount supports most flat screen TVs up to 75 in. (190.5 cm) and 100 lbs. (45.
3-in-1 TV Stand Package contents Parts A Top shelf frame (1) B Middle shelf (1) C Bottom shelf (1) F Spine assembly (1) D Left side frame (1) E Right side frame (1) G Top shelf support (1) I Mounting frame (1) J TV bracket (2) K Cable clip (2) H Swivel bracket (1) www.insigniaproducts.
Hardware LABEL STAND PART L QTY. LABEL 4 V 13 1 W 2 Hex key 4 mm Bolt 5/8" (15.9 mm) N QTY. Plastic end cap Bolt 1/2" (12.7 mm) M STAND PART 4 X 1 Hex key 4.8 mm Bolt 1"’ (25.4 mm) O 12 Y 1 Touch-up pen Bolt 1 1/4" (31.6 mm) P 2 Z 1 Tipping restraint hardware kit Bolt 1 3/4" (44.
3-in-1 TV Stand Hardware (continued) LABEL STAND PART FF QTY. LABEL 4 MM Bolt M6 × 35 mm STAND PART QTY. 4 Lock washer M6 GG 4 NN Bolt M8 × 16 mm 4 Lock washer M8 HH 4 OO 4 Large spacer Bolt M8 × 20 mm II 4 PP 4 Small spacer Bolt M8 × 40 mm JJ 4 QQ 4 Flat washer M4/M5 Bolt M8 × 50 mm KK 4 RR Lock washer M4 4 Flat washer M6/M8 LL 4 Lock washer M5 Tools needed Level Socket wrench Hammer Phillips screwdriver Pencil Edge-to-edge stud finder www.insigniaproducts.
Assembling your stand Tip: Assemble your stand on a carpeted floor or the empty TV stand carton to avoid scratching it. Note: Do not fully tighten all bolts until you finish assembling all of the parts. After assembly, go back and fully tighten all bolts. This will make the assembly easier. STEP 1: Attach the top panel to the spine You need: W 4 mm hex key (1) A Top shelf frame (1) F Spine assembly (1) P Bolt 1 3/4" (2) 1 Align the top shelf frame (A) at a 90° angle to the spine assembly (F).
3-in-1 TV Stand STEP 2: Attach the top shelf support to the top panel and spine You need: M 5/8" bolt (3) Q Lock washer (3) R Flat washer (3) W 4 mm hex key (1) G Top shelf support (1) 1 Align the top shelf support (G) with the center of the top shelf frame (A). 2 Place a flat washer (R), then a lock washer (Q) over the hole in the top of the shelf support and in the two holes on the bottom of the shelf support.
STEP 3: Attach the middle shelf to the spine You need: Q Lock washer (2) B Middle shelf (1) R Flat washer (2) W 4 mm hex key (1) O 1 1/4" bolt (2) 1 Place flat washers (R), then lock washers (Q) over the two drilled holes on the middle shelf (B). Note: The metal frame faces the floor when you turn your stand upright. 2 Insert 1 1/4" bolts (O) through the washers and into the two threaded holes in the middle of the spine (F). Tighten the bolts with the 4 mm hex key (W). Metal frame 10 www.
3-in-1 TV Stand STEP 4: Attach the bottom shelf to the spine You need: Q Lock washer (2) R Flat washer (2) W Hex key 4 mm (1) O 1 1/4" bolt (2) C Bottom shelf (1) 1 Place flat washers (R), then lock washers (Q) over the two drilled holes on the bottom shelf (C). Note: The metal frame faces the floor when you turn your stand upright. 2 Insert 1 1/4" bolts (O) through the washers and into the two threaded holes on the outer edge of the spine (F). Tighten the bolts with the 4 mm hex key (W).
STEP 5: Align and attach the right side frame to the shelves You need: Q Lock washer (4) R Flat washer (4) W Hex key 4 mm (1) O 1 1/4" bolt (4) E Right side frame (1) 1 Place flat washers (R), then lock washers (Q) over the four drilled holes on the inside of the lower shelves (B and C). 2 Insert 1 1/4" bolts (O) through the washers and into the four threaded holes on the right side frame (E). Tighten the bolts with the 4 mm hex key (W).
3-in-1 TV Stand STEP 6: Attach the right side frame to the top panel You need: Q Lock washer (2) R Flat washer (2) W Hex key 4 mm (1) N 1" bolt (2) 1 Place flat washers (R), then lock washers (Q) over the two drilled holes on the inside of the top rail of right side frame (E). 2 Insert 1" bolts (N) through the washers and into the two threaded holes on the top panel (A). Tighten the bolts with the 4 mm hex key (W). www.insigniaproducts.
STEP 7: Attach the left side frame to the shelves You need: Q Lock washer (4) R Flat washer (4) W Hex key 4 mm (1) O 1 1/4" bolt (4) D Left side frame (1) • Follow the steps in STEP 5: Align and attach the right side frame to the shelves on page 12 to attach the left side frame (D) to the lower shelves (B and C). 14 www.insigniaproducts.
3-in-1 TV Stand STEP 8: Fasten the left side frame to the top panel You need: Q Lock washer (2) R Flat washer (2) W Hex key 4 mm (1) N 1" bolt (2) 1 Follow the steps in STEP 6: Attach the right side frame to the top panel on page 13 to attach the left side frame (D) to the top shelf frame (A). 2 Stand the assembled frame upright. Note: • For swivel stand assembly, go to Mounting the TV using the swivel configuration on page 16.
Mounting the TV using the swivel configuration Note: If you are wall-mounting the TV, go to STEP 4: Select the correct bolts, washers, and spacers for your TV on page 19. STEP 1: Attach the swivel bracket to the mounting frame You need: L 1/2" bolt (4) H Swivel bracket (1) Q Lock washer (4) R Flat washer (4) W Hex key 4 mm (1) I Mounting frame (1) 1 Align the four mounting holes on the swivel bracket (H) with the holes on the back side of the mounting frame (I).
3-in-1 TV Stand STEP 2: Attach the swivel bracket assembly to the spine You need: Q Lock washer (6) R Flat washer (6) W Hex key 4 mm (1) M 5/8" bolt (6) Note: The upper spine provides four height options for your TV. Based on your TV size, adjust the swivel bracket (H) to the best height to offer optimum viewing. 1 2 3 4 Place a flat washer (R), then lock washer (Q) over one of the holes on the side of the swivel bracket.
STEP 3: Attach the cable clips You need: W Hex key 4 mm (1) K Cable clip (2) M 5/8" bolt (4) 1 Align a cable clip with two of four possible locations on the spine assembly (F), then insert two 5/8" bolts (M) through the cable clip and into the spine assembly. 2 Repeat for the other cable clip. 3 Tighten the bolts with the 4 mm hex key (W). Cables wrapped on cable clips 18 www.insigniaproducts.
3-in-1 TV Stand STEP 4: Select the correct bolts, washers, and spacers for your TV If you are in doubt about which size bolt to use, try one of the bolts in one of the four Vesa mounting holes on the back of your TV. A bolt that is too large will not fit in the hole at all, but make sure that the bolt size you choose is not too loose. It should grip the hole threads evenly and not wobble. After you determine which size bolts to use, go to the next step.
STEP 5: Determine whether your TV has a flat back or an irregular or obstructed back or a curved screen 1 Carefully place your TV screen face-down on a cushioned, clean surface to protect the screen from damages and scratches. 2 If your TV has a table-top stand attached, remove the stand. See the documentation that came with your TV for instructions. 3 Lay the TV brackets, oriented vertically, on the back of your TV. 4 Align the screw holes in the TV brackets with the mounting screw holes on your TV.
3-in-1 TV Stand STEP 6: Option 1 - Mounting brackets on a TV with a flat back You need: Bolts and Washers or AA M4 × 12 mm bolt (4) or CC M5 × 12 mm bolt (4) or EE M6 × 12 mm bolt (4) or or or KK Lock washer LL Lock washer MM Lock washer M4 (4) M5 (4) M6 (4) or GG M8 × 16 mm bolt (4) HH M8 × 20 mm bolt (4) or NN Lock washer M8 (4) QQ Flat washer M4/M5 (4) J TV bracket (2) Phillips screwdriver RR Flat washer M6/M8 (4) Level 1 Insert the selected bolts through the washers and correct mounting hole
STEP 6: Option 2: Mounting bracket on a TV with an irregularly shaped or obstructed back or a curved screen TV You need: Bolts and Washers or or BB M4 × 30 mm bolt (4) DD M5 × 30 mm bolt (4) or or or FF M6 × 35 mm bolt (4) or II M8 × 40 mm bolt (4) JJ M8 × 50 mm bolt (4) J TV bracket (2) KK Lock washer M4 (4) LL Lock washer M5 (4) or MM Lock washer M6 (4) PP Small spacer (4) OO Large spacer (4) Phillips screwdriver NN Lock washer M8 (4) or QQ Flat washer M4/M5 (4) RR Flat washer M6/M8 (4)
3-in-1 TV Stand STEP 7: Attach the TV to the mounting frame on the swivel bracket Note: If you are wall-mounting the TV, go to Mounting the TV using the wall-mount configuration on page 26. You need: Phillips screwdriver 1 With the help of another adult, lift the TV up to the mounting frame (I). 2 Set the hooks on TV brackets (J) over the mounting frame (I), then lower the hooks onto the bars of the mounting frame.
STEP 8: Adjusting the tilt You need: X 4.8 mm Hex key (1) The TV brackets (J) let you make a tilt adjustment of up to 11° down and 5° up to provide optimum viewing and minimize glare. 1 Turn the tension knobs counterclockwise to loosen the knobs on both TV brackets (J), then grasp the edge of the TV and move it up or down to the position you want. 2 Turn the tension knob clockwise to tighten the brackets in position. Use the 4.8 mm hex wrench (X) to tighten the tension knobs, if necessary.
3-in-1 TV Stand STEP 9: Position your TV stand and install the tipping restraint hardware kit You need: Z Tipping restraint hardware kit (1) Level A Metal bracket (2) B Nylon strap (1) 1/8" drill bit Power drill Pencil Edge-to-edge stud finder C Long screw (1) D Short screw (1) 1 Position your assembled stand against a wall where you plan to use it. 2 Adjust the leveling feet to level your TV stand. 3 Align the spine (F) with a stud and mark the wall at the center point of the stud.
Mounting the TV using the wall-mount configuration STEP 1: Remove the upper spine You need: W 4 mm hex key (1) • Unscrew the four bolts and the washers on the spine assembly (F), then remove the upper spine from the spine assembly. 26 www.insigniaproducts.
3-in-1 TV Stand STEP 2: Insert the end cap You need: V Plastic end cap (1) • Plug the plastic end cap (V) all the way onto the top of the lower spine (F). www.insigniaproducts.
STEP 3: Attach the cable clips You need: W Hex key 4 mm (1) K Cable clip (2) M 5/8" bolt (4) • Fasten two cable clips (K) to the back of lower spine (F) using four 5/8" bolts (M). Cables wrapped on cable clips 28 www.insigniaproducts.
3-in-1 TV Stand STEP 4: Option 1 - Mount the frame to a stud wall If you are mounting the TV on a concrete or block wall, to go STEP 4: Option 2- Mount the frame to a block or concrete wall on page 30. You need: Level Hammer 3/16" wood drill bit S Lag bolt (4) Power drill Pencil U Large flat washer (4) Edge-to-edge stud finder Socket wrench 1 Use a stud sensor to locate two adjacent wall studs, then position the mounting frame (I) exactly between the two studs.
STEP 4: Option 2- Mount the frame to a block or concrete wall You need: Level T Concrete anchor (4) Hammer 7/16” masonry drill bit S Lag bolt (4) Power drill Pencil U Large flat washer (4) Edge-to-edge stud finder Socket wrench 1 Place the mounting frame (I) against the wall where you intend to mount the TV. Use a level to make sure that the mounting frame is level, then mark the four mounting holes on the wall. Remove the mounting frame.
3-in-1 TV Stand STEP 5: Attach the TV to the mounting frame on the wall You need: Phillips screwdriver 1 Depending on the type of TV that you own, attach the TV brackets (J) to the back of the TV following the steps in: • STEP 5: Determine whether your TV has a flat back or an irregular or obstructed back or a curved screen on page 20 • STEP 6: Option 1 - Mounting brackets on a TV with a flat back on page 21 • STEP 6: Option 2: Mounting bracket on a TV with an irregularly shaped or obstructed back or a c
STEP 6: Adjust the tilt You need: X 4.8 mm Hex key (1) The TV brackets (J) let you make a tilt adjustment of up to 11° down and 5° up to provide optimum viewing and minimize glare. 1 Loosen the tension knobs on both TV brackets (J), then grasp the edge of the TV and move it up or down to the position you want. 2 Turn the tension knob clockwise to secure the brackets in position. Use the 4.8 mm hex wrench (X) to tighten the tension knobs, if necessary. 5° ~ 11° Turn clockwise to tighten.
3-in-1 TV Stand Mounting the TV using the tabletop configuration STEP 1: Remove the upper spine You need: W 4 mm hex key (1) • Unscrew the four bolts and the washers on the spine assembly (F), then remove the upper spine from the spine assembly. www.insigniaproducts.
STEP 2: Insert the end cap You need: V Plastic end cap (1) • Plug the plastic end cap (V) all the way onto the top of the lower spine (F). 34 www.insigniaproducts.
3-in-1 TV Stand STEP 3: Attach the cable clips You need: W Hex key 4 mm (1) K Cable clip (2) M 5/8" bolt (4) • Fasten two cable clips (K) to the back of lower spine (F) using four 5/8" bolts (M). Cables wrapped on cable clips www.insigniaproducts.
STEP 4: Position your TV stand and install the tipping restraint hardware kit You need: Level Z Tipping restraint hardware kit (1) Pencil Edge-to-edge stud finder 1/8" drill bit Power drill 1 Position your assembled stand against a wall where you plan to use it. 2 Adjust the leveling feet to level your TV stand. 3 Follow the instructions printed on the bag containing the tipping restraint hardware kit (Z) to attach the restraint hardware to the wall and your stand.
3-in-1 TV Stand Maintaining your TV stand Wood/Laminate • Use your favorite type of furniture polish. • Do not spray polish directly onto the stand. Spray onto a soft cloth, then wipe the stand. • Always test any polish in a discrete location first, such as the back of the stand, to make sure that there is no adverse reaction. • Dust frequently with a soft cloth. • Never slide objects across surfaces. Lift objects from the top surface rather than dragging them across the finish when moving them.
ONE-YEAR LIMITED WARRANTY Definitions: The Distributor* of Insignia branded products warrants to you, the original purchaser of this new Insignia-branded product (“Product”), that the Product shall be free of defects in the original manufacturer of the material or workmanship for a period of one (1) year from the date of your purchase of the Product (“Warranty Period”).
www.insigniaproducts.com 1-877-467-4289 (U.S. and Canada) or 01-800-926-3000 (Mexico) INSIGNIA is a trademark of Best Buy and its affiliated companies. Distributed by Best Buy Purchasing, LLC 7601 Penn Ave South, Richfield, MN 55423 U.S.A. ©2021 Best Buy. All rights reserved.
