USER GUIDE TV Console for up to 75" TVs NS-HWG1965 SAFETY INFORMATION AND SPECIFICATIONS..2 PACKAGE CONTENTS: PARTS...................................3 PACKAGE CONTENTS: HARDWARE .......................4 ASSEMBLY INSTRUCTIONS.......................................6 CARE AND MAINTENANCE ................................... 22 NS-HWG1965 Before using your new product, please read these instructions to prevent any damage.
NS-HWG1965 SAFETY INFORMATION AND SPECIFICATIONS CAUTION: The console’s top work surface is designed for use with a product weighing no more than 135 lbs. (61.2 kg) and having a width that permits it to sit evenly on the console with no more than a one-inch overhang on each side of the top panel. Use with products that weigh more than the maximum weight allowed, or with dimensions that extend beyond the maximum width may result in instability, which may result in injury.
TV Console for up to 75" TVs Tools needed: Hammer Phillips screwdriver 3/8” drill bit Rubber mallet Pliers Power drill PACKAGE CONTENTS: PARTS Make sure that you have all the parts necessary to assemble your new TV stand. A Top panel (1) Note: Keep the stopper template attached to the top panel.
NS-HWG1965 PACKAGE CONTENTS: HARDWARE Note: You may receive extra hardware. Make sure that you have all the hardware necessary to assemble your new TV stand. Label Hardware Qty. Label Hardware Qty. N Wood dowel M8 x 30 mm 26 X P Cam pin 22 Y 22 Z AA Floor leveler 2 BB Stopper 2 Q Cam lock R Screw M4 x 50 mm 6 S Flat head screw M3.5 x 15 mm 10 Knob Knob bolt Corner connector Glue CC T Washer head screw M3.
TV Console for up to 75" TVs INSTALLATION TIPS Gluing wood dowels (N) When using a wood dowel (N), put one drop of glue (CC) in the hole before you insert the wood dowel (N). Insert the wood dowel (N), then gently tap it with a rubber mallet to secure it in place. 1 GLU 2 3 E 4 FINAL X Locking cam pins (P) and cam locks (Q) 1 One end of a cam pin (P) is threaded so that it screws into place. The other end is not threaded.
NS-HWG1965 ASSEMBLY INSTRUCTIONS Step 1: Screw cam pins onto the top panel, bottom shelf, and skirtings Tip: Assemble your stand on a carpeted floor or the empty TV stand carton to avoid scratching it. • Securely screw the cam pins (P) into the designated small holes on the top panel (A), bottom shelf (E), front skirting (F) and side skirtings (H and I) using a Phillips screwdriver. You’ll need: P (22) 6 Phillips screwdriver www.insigniaproducts.
TV Console for up to 75" TVs Step 2: Attach the back skirting between the side skirtings 1 Glue two wood dowels (N) into the drilled holes on the ends of the back skirting (G). Tip: See “Gluing wood dowels (N)“ on page 5 for more information. 2 Attach the back skirting to the side skirtings (H and I) by inserting two cam locks (Q) and tightening with a screwdriver. Make sure that the cam screw holes face inward. Tip: See “Locking cam pins (P) and cam locks (Q)“ on page 5 for more information.
NS-HWG1965 Step 3: Attach the front skirting to the side skirtings 1 Glue two wood dowels (N) into the drilled holes on the front skirting (F). 2 Attach the front skirting (F) to the side skirtings (H and I) by inserting two cam locks (Q) and tightening with a screwdriver. Make sure that the cam screw holes face inward. You’ll need: N (2) 8 Q (2) CC (1) www.insigniaproducts.
TV Console for up to 75" TVs Step 4: Attach the assembled base to the bottom shelf 1 Glue 10 wood dowels (N) into the drilled holes on the bottom shelf (E). 2 Position the assembled base onto the wood dowels (N) and cam pins (P) on the bottom shelf (E). Make sure that the pilot holes for the corner connectors face the front of the bottom shelf. Tip: Try working from one end to the other to slide the assembled base into place.
NS-HWG1965 Step 5: Install two floor levelers to the assembled base 1 Using the pilot holes as a guide, fasten two corner connectors (Z) to the joints where the front skirting (F) meet with the side skirtings (H and I) with eight 15 mm flat head screws (S). 2 Screw two floor levelers (AA) onto the installed corner connectors (Z). AA You’ll need: S (8) 10 Z (2) AA (2) www.insigniaproducts.
TV Console for up to 75" TVs Step 6: Attach two door stoppers to the top panel Note: Keep the stopper template attached to the top panel (A). • Using the pilot holes as a guide, attach two door stoppers (U) onto the front supports on the top panel (A) with one 15 mm flat head screw (S) per stopper. Make sure that the right angle sides of the stoppers face the front of the unit. The countersunk hole is located at the bottom and faces outward You’ll need: Phillips screwdriver S (2) U (2) www.
NS-HWG1965 Step 7: Align and attach the side panels to the top panel 1 Glue two wood dowels (N) into the holes on the top edge of the left side panel (B). 2 Attach the left side panel to the top panel (A) by inserting two cam locks (Q) and tightening with a screwdriver. Make sure that the door hinge mounts are on the same side as the door stoppers. 3 Repeat this process to attach the right side panel (C) on the opposite end.
TV Console for up to 75" TVs Step 8: Attach the partition panel to the top panel 1 Glue two wood dowels (N) into the inner holes on the top edge of the partion panel (D). 2 Attach the partition panel to the top panel (A) by inserting two cam locks (Q) and tightening with a screwdriver. Door hinge mounting bases point towards the front of the unit You’ll need: N (2) Q (2) CC (1) www.insigniaproducts.
NS-HWG1965 Step 9: Attach the bottom shelf to both side panels and partition panel 1 Glue six wood dowels (N) into the holes on the bottom edge of side panels (B and C) and partition panel (D). 2 Align the drilled holes on the bottom shelf (E) with the installed wood dowels (N) on both side panels (B and C) and partition panel (D), then press them together. Make sure that the leveling feet are on the same side as the hinges.
TV Console for up to 75" TVs Step 10: Attach the back panel to the assembled console frame 1 Go back and tighten all cam locks and screws. Make sure that all the parts are tight and there are no gaps between the pieces. This will help keep the unit square. 2 Turn the assembled unit over so that its back is facing up. 3 Unfold the back panel (J) and align its holes with the pilot holes along the edges of the assembled unit. 4 Use the washer head screws (T) to secure the back panel to the assembled unit.
NS-HWG1965 Step 11: Attach adjustable shelves 1 Stand the assembled unit upright. 2 Insert the small and large cam lock covers (V and EE) into the cross slots on the visible cam locks on the vertical panels (B, C, and D). 3 Insert eight shelf supports (W) into the holes in the sides of the compartments. Make sure that you place the shelf supports at the same level so the shelves are not tilted. 4 Tilt and rest the adjustable shelves (K) onto the shelf supports (W). EE You’ll need: V (2) 16 EE (4) www.
TV Console for up to 75" TVs Step 12: Attach doors to the vertical panels 1 Push the knob bolts (Y) through the inside of each door (L), then screw on the knobs (X). 2 Attach a door (L) to the right side panel (C) by engaging both door hinges together as shown: A Extend both hinges of the door (L) to the open position, if needed. B Slide the back hooks (on the door hinges) into the slots on the ends of the mounting bases.
NS-HWG1965 Step 13: Attach the bumpers to the door stoppers • Peel two bumpers (DD) from the bumper card and attach one to each door stopper (U) where it will contact the door (L). DD DD You’ll need: DD (4) 18 www.insigniaproducts.
TV Console for up to 75" TVs Step 14: Attach the stopper to the top panel To prevent your TV from tipping, you must follow these instructions if you place a TV on top of your stand. Otherwise, skip to “Step 15: Change the door panel” on page 20. If your TV has one base: 1 Remove the paper backing from the stopper (BB), then place it in the cut-out of the stopper template on the top panel (A). Press down on the stopper (BB) to help adhesion.
NS-HWG1965 Step 15: Change the door panel Follow these steps if you want to change your TV stand’s door panels from glass to wood. Otherwise, skip to “Step 16: Position the TV stand and install the tipping restraint hardware kit” on page 21. 1 Open a door (L) and loosen the screws on the inside of the door frame. 2 Rotate the clips to remove the old panel. 3 Insert the new panel, then rotate the clips and tighten the screws to secure the panel in the door frame.
TV Console for up to 75" TVs Step 16: Position the TV stand and install the tipping restraint hardware kit 1 Position the assembled stand against the wall where you plan to use it. 2 Adjust the leveling feet to level the TV stand. 3 Follow the instructions printed on the bag containing the tipping restraint hardware kit (GG) to attach the restraint hardware to the wall and the stand. WARNING: It is very important that the tipping restraint is installed correctly.
NS-HWG1965 CARE AND MAINTENANCE Wood/Laminate • • • • • • • • • Use your favorite type of furniture polish. Do not spray polish directly onto the stand. Spray onto a soft cloth then wipe the stand. Clean spills immediately with a soft, damp cloth. Always test any polish in a discrete location first, such as the back of the stand, to make sure that there is no adverse reaction. Dust frequently with a soft cloth. Never slide objects across surfaces.
TV Console for up to 75" TVs ONE-YEAR LIMITED WARRANTY Definitions: The Distributor* of Insignia branded products warrants to you, the original purchaser of this new Insignia-branded product (“Product”), that the Product shall be free of defects in the original manufacturer of the material or workmanship for a period of one (1) year from the date of your purchase of the Product (“Warranty Period”).
1-877-467-4289 (U.S. and Canada) or 01-800-926-3000 (Mexico) www.insigniaproducts.com INSIGNIA is a trademark of Best Buy and its affiliated companies. Registered in some countries. Distributed by Best Buy Purchasing, LLC 7601 Penn Ave South, Richfield, MN 55423 U.S.A. ©2021 Best Buy. All rights reserved.
