USER GUIDE 47” Computer Desk NS-ODS3 Before using your new product, please read these instructions to prevent any damage.
Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Safety information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
47” Computer Desk Features • • Metal legs help to provide stability Holds up to 70 lbs. Dimensions 47 in. (119.4 cm) 1.5 in. (3.8 cm) 30 in. (76.2 cm) 28.5 in. (72.4 cm) 23.2 in. (59 cm) Parts included 1 Desktop 2 Leg frames (2) 4 Left support bar 5 Right support bar www.insigniaproducts.
Hardware included LABEL HARDWARE QTY. A M6 × 60 mm bolts 4 B Crosshead nuts 4 C M6 × 35 mm bolts 2 D M6 × 15 mm bolts 2 E 4 × 25 mm screws 4 LABEL HARDWARE QTY. F Hex wrench 1 G Washers 4 H Wall straps 2 I Wall anchors 2 J 4 × 40 mm screws 2 Tools needed CAUTION: Do not use a drill to assemble your desk. The drill should only be used to secure your desk to the wall (step 3). Phillips screwdriver (PH2) Hammer Drill with 1/4 in.
47” Computer Desk Assembling your desk STEP 1: Attach the leg frames and bottom support bar You need: 1 Desktop A M6 × 60 mm bolts (4) 2 Leg frames (2) B Crosshead nuts (4) C M6 × 35 mm bolts (2) 3 Bottom support bar F Hex wrench 1 Insert four crosshead nuts (B) into the desktop (1), making sure that the arrows are pointing toward the nearest side edge. 2 Align a leg frame (2) with the holes on a side of the desktop, making sure that the hole near the foot is toward the back of the desktop.
STEP 2: Attach the left and right support bars and wall straps You need: 5 Right support bar D M6 × 15 mm bolts (2) E 4 × 25 mm screws (4) F Hex wrench G Washers (2) H Wall straps (2) 4 Left support bar Phillips screwdriver 1 Align the straight end of the left support bar (4) with the hole on the left side of the bottom support bar (3), then secure with an M6 × 15 mm bolt (D) using the hex wrench (F). Do not fully tighten the bolt.
47” Computer Desk STEP 3: Secure your desk to the wall You need: G Washers (2) I Anchors (2) J 4 × 40 mm screws (2) Drill with 1/4 in. (6 mm) bit Phillips screwdriver Hammer WARNING: • DO NOT SKIP THIS STEP. Securing your desk protects children and pets from accidental tip-overs and injury. • The included screws (J) and anchors (I) are intended for securing your desk to drywall only. If your wall is made of a different material, you must purchase appropriate anchors and screws separately.
STEP 4: Leveling your desk • 8 You can adjust the desk’s feet to level the desk. www.insigniaproducts.
47” Computer Desk Cleaning your desk • • Clean the surface of your desk with a duster or damp cloth only. Do not use abrasive cleaners. Specifications Dimensions (H × W × D) 30 × 47 × 23.2 in. (76.2 × 119.4 × 59 cm) Weight 23.3 lbs. (10.6 kg) Maximum supported weight 70 lbs. (31.8 kg) Troubleshooting PROBLEM POSSIBLE SOLUTIONS My desk wobbles • • A piece won’t fit Your desk comes equipped with adjustable feet on the bottoms of the leg frames (2).
ONE-YEAR LIMITED WARRANTY Definitions: The Distributor* of Insignia branded products warrants to you, the original purchaser of this new Insignia-branded product (“Product”), that the Product shall be free of defects in the original manufacturer of the material or workmanship for a period of one (1) year from the date of your purchase of the Product (“Warranty Period”).
For product inquiries, please contact us with the information below: 1-877-467-4289 www.insigniaproducts.com INSIGNIA is a trademark of Best Buy and its affiliated companies. Distributed by Best Buy Purchasing, LLC 7601 Penn Ave South, Richfield, MN 55423 U.S.A. ©2022 Best Buy. All rights reserved.
