Use and Care Manual

Manufactured by Benjamin Moore & Co. 101 Paragon Drive, Montvale, NJ 07645 Tel: [phone] www.benjaminmoore.com/inslx M72 HTF-XXX EN 022221
HOT TRAX
®
ACRYLIC CONCRETE & GARAGE FLOOR PAINT
SATIN FINISH HTF-XXX
Features General Description
 Water-Based Ready to Use
Garage Floor Coating
 Resists Hot Tire Pick-Up
from Cars
 Low VOC Formula
 Soap & Water Clean-Up
 Protects from Chemicals,
Water, Oil
& Grease
 Durable Satin Finish
 Fast Return to Service
(refer to Page 2)
Hot Trax
®
Acrylic Concrete and Garage Floor Paint is a high
performance, ready to use acrylic floor coating that resists hot
tire pick-up and marring common to driveways and garage
floors. This finish seals and protects concrete from chemicals,
water, oil and grease. Hot Trax
®
is also ideal for use on
exterior concrete, masonry, stucco, cinder block and brick.
This durable low satin finish is resistant to cracking. This
product can be walked on in 24 hours and vehicles
can be
parked on Hot Trax
®
in 5 – 7 days.
Recommended For Limitations
For interior and exterior use on concrete floors, basement floors,
garage floors, driveways, walkways, patios and pavers. Also can
be used on masonry, stucco, block and brick.
 Do not apply if surface or air temperature is below 50 °F
(10 °C)
 Do not apply if temperature is within 5° of Dew Point or if
rain is expected within 12 hours.
 Do not paint in direct sunlight or on hot surfaces.
Product Information
Colors — Standard:
Silver Gray (HTF309), Light Gray (HTF310)
Technical Data
Tintable White
Vehicle Type Modified Acrylic
Pigment Type Titanium Dioxide
Volume Solids 37 ± 1.0%
Coverage per Gallon at
Recommended Film Thickness
300 – 400 Sq. Ft.
Recommended Film
Thickness
– Wet 4.0 – 5.3 mils
– Dry 1-5 – 2.0 mils
Depending on surface texture and porosity. Be sure to
estimate the right amount of paint for the job. This will ensure
color uniformity and minimize the disposal of excess paint.
Dry Time @ 77 °F
(25 °C) @ 50% RH
– Tack Free
2 – 4 Hours
– To Recoat 24 Hours
– Return to
Service
Foot Traffic – 24 Hours
Vehicular Traffic – 5 Days
High humidity and cool temperatures will result in longe
r
dry, recoat and service times.
Dries By Evaporation
Viscosity 95 – 100 KU
Flash Point
200 °F or greate
r
(TT-P-141, Method 4293)
Gloss / Sheen Satin (5 – 10 @ 60°)
Surface Temperature
at Application
– Min. 50 °F
– Max. 90 °F
Thin With Not Necessary
Clean Up Thinner Warm Soapy Wate
r
Weight Per Gallon 10.5 lbs.
Storage Temperature
– Min. 50 °F
– Max. 90 °F
Volatile Organic Compounds (VOC)
47.7 Grams/Liter 0.39 Lbs./Gallon
— Tint Bases:
Tintable White (HTF-110), Accent Base (HTF-894)
Tint with Benjamin Moore
®
Gennex
®
, Color Preview
®
or Universal colorant
— Special Colors:
Contact your retailer.
Certifications & Qualifications:
VOC compliant in all regulated areas
The products supported by this data sheet contain a maximum of 50 grams
per liter VOC/VOS (0.41 lbs/gal.) excluding water and exempt solvents
This product qualifies for LEED (Leadership in Energy and Environmental
Design) projects as a Floor Coating
Technical Assistance:
Available through your local authorized independent Insl-x retailer.
For the location of the retailer nearest you, call 1-866-708-9180, or visit
www.benjaminmoore.com/inslx
◊ Reported values are for Tintable White