Instructions / Assembly

CABINET COAT
TRIM & CABINET ENAMEL
SATIN FINISH CC-45XX
Features
General Description
• Urethane acrylic cabinet
and trim finish
• Resists chipping,
scuffing, food stains,
grease & water
• Super adhesion
• Waterborne formula
provides an ultrasmooth
“factorylike” finish
• Durable satin finish
Cabinet Coat is the ultimate finish for refurbishing dingy kitchen
and bathroom cabinets, shelving, furniture, trim & crown molding
and other interior applications that require an ultra smooth, factory
like finish with long lasting beauty. Its superior adhesion allows
painting difficult surfaces, even polyurethane and varnish, without
using a primer. Cabinet Coat offers excellent flow and leveling,
superior stain resistance and an extremely durable satin finish that
will look like new for years.
Recommended For
Limitations
Cabinets, Metal, New & Previously Painted Wood, Furniture,
Woodwork, Doors Trim. For exterior use, limit to small areas
of trim. Do not use as a whole house wall paint.
• Do not apply when air, product or surface temperature is
below 50 ºF (10°C) or above 90 ºF (32°C) or within 5ºF of
the dew point.
• Not for surfaces that will be immersed in liquids (sinks or
tubs) or the surface of stoves or ovens.
Product Information
Colors — Standard:
CC-45100, White
Technical Data◊
White
Vehicle Type
Urethane Reinforced Acrylic
Pigment Type
Titanium Dioxide
Volume Solids
33.1 ± 1.0%
Coverage per Gallon at
Recommended Film Thickness
350 - 450 Sq. Ft.
Recommended Film
Thickness
– Wet
3.6 - 4.6 mils
– Dry
1.2 - 1.5 mils
Depending on surface texture and porosity. Be sure to estimate
the right amount of paint for the job. This will ensure color
uniformit
y and minimize the disposal of excess paint.
Dry Time @ 77°
F
(25°
C) @ 50% RH
– Tack Free
1 Hour
– To Recoat
6 Hours
– Full Cure
5 – 7 Days
High humidity and cool temperatures will result in longer
dry,
recoat and service times.
Dries By
Coalescence
Viscosity
90 – 100
KU
Flash Point
200°
F or greater
(TT-P-
141, Method 4293)
Gloss / Sheen
Satin 27 - 32 units @60
°
Surface Temperature at
Application
– Min.
50°F
– Max.
90°F
Thin With
Do Not Thin
Clean Up Thinner
Warm Soapy Water
Weight Per Gallon
10.4 lbs.
Storage Temperature
– Min.
50°F
– Max.
90°F
Volatile Organic Compounds (VOC)
47 Grams/Liter 0.42 Lbs./Gallon
— Tint Bases:
CC-45600, Tint Base, Use universal colorants
— Special Colors:
Contact your dealer.
Certification:
The product supported by this data sheet contains a maximum of 50
grams per liter VOC/VOS (0.42 lbs/gal.) excluding water & exempt
solvents.
This product is compliant under the Ozone Transport Commission
regulations as a Non-Flat Coating.
This product is currently approved under MPI #140.
This product meets the qualifications for LEED (Leadership in Energy
and Environmental Design) projects as a Non-Flat Coating.
Technical Assistance:
Available through your local authorized independent Insl-x dealer. For
the location of the dealer nearest you, call 1-800-225-5554, or visit
www.insl-x.com
◊ Reported values are for White. Contact dealer for values of other
bases or colors.
Manufactured by Benjamin Moore & Co. 101 Paragon Drive, Montvale, NJ 07645 Tel: [phone] Fax: [phone] www.Insl-x.com M72 CC-45XX US 102714