User Manual

Manufactured by Benjamin Moore & Co. 101 Paragon Drive, Montvale, NJ 07645 Tel: [phone] Fax: [phone] www.Insl-x.com M72 SXA-110 US 090517
STIX
®
WATERBORNE BONDING PRIMER
SXA-110
Features
General Description
 Strongly Bonds to Glossy
Surfaces
 Unparalleled Adhesion to
the Most Challenging
Surfaces.
 Excellent Holdout
 Low Odor
 Soap & Water Clean-up
 Cures as low as 35ºF
(1.7°C)
Stix
®
Waterborne Bonding Primer is a premium quality, waterborne,
acrylic urethane primer/sealer with unparalleled adhesion to the
most challenging surfaces, including PVC, Vinyl, Plastic, Glass,
Tile, Glazed Block, Glossy Paints, Pre-Coated Siding, Fiberglass,
and Galvanized Metals. Stix is also ideal for use on plaster, drywall,
wood, and non-ferrous metals, where a low ambient or surface
temperature would present a problem for conventional primers.
Offers an extremely hard film when cured. Use it on interior and
exterior surfaces and topcoat with almost any type of coating
including Alkyd, Acrylic Latex, Urethane, Epoxy, and Lacquer
Finishes. Stix levels to a smooth surface and cleans up with soap
and water.
Recommended For
Limitations
Interior and Exterior surfaces. Drywall, Plaster, Ceiling,
Acoustical Tile, Wood Trim & Doors, Formica, Ceramic Tiles,
Glossy Surfaces, PVC Plastic, Masonry Walls, Wood, Trim,
Shutters, Masonry, Stucco, Concrete, Cement Block,
Galvanized Metal, Aluminum, etc.
 Apply when air and surface temperatures are above 35°F
 Do not apply in direct sunlight or on a hot surface. Avoid rain,
moisture or high humidity for the first 24 hours of curing
 Not intended for immersion service or continuous water contact.
Not for below grade applications
 Not recommended for use over polyethylene or polypropylene.
Stix
®
must be top coated for exterior use
 Not recommended over Kynar
®
(and similar finishes) unless
tested and approved by the buyer
 Not recommended as a whole house exterior primer over wood
Product Information
Colors — Standard:
SXA-110, White
Technical Data
White
Vehicle Type
Urethane Modified Acrylic
Pigment Type
Titanium Dioxide
Volume Solids
40.0 ± 1.0%
Coverage per Gallon at
Recommended Film Thickness
300 – 400 Sq. Ft.
Recommended Film
Thickness
– Wet
4.0 - 5.5 mils
– Dry
1.6 - 2.2 mils
Depending on surface texture and porosity. Be sure to estimate the
right amount of paint for the job. This will ensure color uniformity and
minimize the disposal of excess paint.
Dry Time @ 77°F
(25°C) @ 50% RH
– Tack Free
30 Minutes
– To Recoat
3 – 4 Hours
– Full Cure
3 – 4 Days
High humidity and cool temperatures will result in longer dry, recoat
and service times.
Dries By
Coalescence
Viscosity
70 – 80 KU
Flash Point
200° F or greater (TT-P-141, Method 4293)
Gloss / Sheen
Flat
Surface Temperature at
Application
– Min.
35°F
– Max.
90°F
Thin With
Do not Thin
Clean Up Thinner
Warm, Soapy Water
Weight Per Gallon
11.0 lbs.
Storage Temperature
– Min.
45°F
– Max.
95°F
Volatile Organic Compounds (VOC)
87.6 grams/liter .73 lbs./gallon
— Tint Bases:
N/A
Can be Tinted With a Maximum of 2 oz. Universal Colorant per gallon
— Special Colors:
Contact your dealer.
Certification:
All products supported by this data sheet contain a maximum of 100 grams
per liter VOC/VOS (.83 lbs. /gal.) excluding water & exempt solvents.
Emission certified per California Department of Public Health
CDPH/EHLB/Standard Method Version 1.2, 2017
(Emission testing method for CA Specification 01350).
Qualifies for CHPS credit
Qualifies for LEED v4 credit.
Technical Assistance:
Available through your local authorized independent Insl-x dealer. For the
location of the dealer nearest you, call 1-866-708-9180 or see
www.insl-x.com
◊ Reported values are for White. Contact dealer for values of other
bases or colors.